Parts for Ge GTD65EBSJ3WS: Drum Parts

Secures dryer panels and internal components to the cabinet frame. Replace if screw is stripped, missing, or loose to prevent vibration and rattling.

This replacement screw secures appliance panels and internal components per your model's hardware list. Replace lost or stripped screws to keep assemblies tight, reduce vibration and rattles, and maintain proper alignment.

• Fastens brackets, covers, and sheet-metal panels as specified in the parts diagram
• Restores proper fit when an original screw is missing, stripped, or damaged
• Helps eliminate rattling or vibration from loose hardware
• Keeps components safely in place during operation

• Disconnect power to the appliance before servicing
• Match length, head style, and thread to the original; install in the same location/quantity
• Start threads by hand to avoid cross-threading; tighten with the correct driver
• Do not overtighten, especially into plastic or thin sheet metal

If your dryer clothes are rubbing or tumbling unevenly, a worn drum assembly may be the cause. This rotating tub holds and tumbles laundry for efficient drying.

Fix melted plastic or goop marks on clothes with a new dryer heat diffuser. Replaces damaged diffuser that causes staining. DIY repair with 3 screws.

Dryer not heating or overheating? A faulty thermostat disrupts temperature regulation, preventing proper drying. This part monitors drum heat levels.

The Inlet Control Thermistor is an OEM part for GE dryers. It monitors and regulates the temperature of the incoming air to ensure optimal drying performance. This thermistor sends temperature readings to the dryer's control board, which adjusts the heating element accordingly to maintain the desired temperature throughout the drying cycle.

You should replace this inlet control thermistor if it becomes faulty or fails to provide accurate temperature readings. Common causes of a bad thermistor include electrical failures, damage from overheating, or wear and tear from regular use.

Symptoms of a bad inlet control thermistor include:

• Dryer not heating properly
• Overheating or uneven drying
• Dryer shutting off prematurely
• Error codes related to temperature issues

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The High Limit Thermostat is an OEM replacement part for GE electric dryers. Located internally near heating components, this safety device monitors drum temperatures to prevent excessive heat accumulation.

Causes of malfunction relate to water residues creating shorts, loose terminals detaching wiring due to vibrations, or a worn heat sensitive mechanism reacting slower over time.

Symptoms involve:

• Repeated thermal cut-off trips mid-cycle
• Inability to select heat settings without errors shown
• Bleach or smoke smells indicating unregulated temperatures

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Plastic baffle that installs inside the dryer drum to lift and tumble clothes. Replace if cracked, broken, thinning, or missing vanes that may mark fabrics.

Protection bracket for dryers. Mounts internally to shield components from damage. Replace if bent, broken, or missing to restore proper protection.

Dryer not heating or taking too long to dry? This heating element and housing assembly restores heat production. DIY-friendly repair for electric dryers.

If your dryer isn't heating properly or has inconsistent drying, the heater housing may need replacement. This part directs heated air into the drum.

If your dryer runs but clothes stay wet or drying takes too long, the heating element may have failed. This coil heats air to dry clothes efficiently.

Bonds dryer cabinet to ground point for safe operation. Replace if damaged, broken, or missing to restore proper electrical grounding and reduce shock risk.

Supports and stabilizes the dryer drum for smooth rotation. Replace if shaft is worn, bearing is damaged, or drum wobbles or sinks at the rear.

This is a small screw, and it is made for dryers, washers, and washer dryer combos. This is a genuine replacement part made by General Electric. Screws are common in these appliances and can cause many difficulties if they become loose, damaged, or missing.A new screw might be needed if there are areas in the appliance that seem off balance or not level. Another way to tell if a new screw is needed is if there are parts in the appliance that are loose or falling off. This is common over many years of normal use as the shaking of washers and dryers can eventually lead to loose screws. Be sure the washer or dryer is completely off before attempting to replace any screws.This is an OEM part sourced directly from the manufacturer. It is sold individually and is compatible with washers, dryers, and washer dryer combos made by General Electric.

The bearing retainer secures the drum bearing assembly in your dryer. Replace if cracked, broken, or worn to restore proper structural support.

Supports the rear dryer drum for smooth, quiet rotation. Replace if you hear squeaking, screeching, or thumping during cycles. Verify fit with your model.

The O Ring is an OEM part for GE dryers, creating a tight seal in different components for efficient operation. This small part prevents air leaks that can impact drying performance, made from quality materials to withstand high temperatures and frequent use

Causes of a faulty O Ring in a dryer may stem from heat exposure, regular wear and tear, or chemical damage. This can result in reduced elasticity, cracks, or breaks, impacting the seal.

Symptoms of a bad O Ring in your dryer include:

• Reduced efficiency in drying, as air leaks can affect the dryer's ability to maintain the correct temperature.
• Unusual noises stemming from air escaping through the compromised seal.
• Potential for small leaks or condensation within the dryer's internal components, leading to moisture issues.

This genuine GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.