Parts for Electrolux E30EW75PPSD: Body Parts

Broiler pan rack for electric ovens and ranges. Replaces cracked, warped, or missing racks. Installs inside broiler pan for elevated cooking.

Oven broiler pan catches drippings and supports food during broiling. Replace this pan if yours is warped, damaged, or missing for safe cooking and easier cleanup.

This broiler insert is the oven pan insert that sits under the broiler burner to catch drips and help direct heat for even browning. It restores a stable cooking surface and keeps the broiler area cleaner. What it does:

• Holds food and catches grease and drips during broiling to prevent mess and flare-ups
• Directs heat from the broiler for consistent browning and searing
• Replaces damaged, warped, or corroded inserts that cause uneven cooking
• Helps prevent food from falling into the burner area

• One broiler insert

• Disconnect power to the appliance and allow the oven to cool completely before servicing
• Remove oven racks and slide the old insert out; position the new insert so it seats securely in the broiler cavity
• Wear heat-resistant gloves when testing the broiler after installation and inspect for proper fit before use
• Do not modify the part; use only as designed for the oven broiler assembly

This seal creates a watertight barrier at a critical joint inside the dishwasher. Replacing a flattened, cracked, or missing seal helps stop leaks during the cycle and protects surrounding components from moisture. What it does:

• Maintains a watertight seal between mating parts in the wash system
• Helps prevent drips and pooling water under or around the appliance
• Restores proper sealing after wear, hardening, or deformation
• Common signs include leaks during a cycle, moisture beneath the unit, or visible wear on the old seal

• 1 seal

• Disconnect power and shut off the water supply before servicing
• Access the sealed area per your model's service information; remove the old seal
• Clean the groove/mating surfaces; seat the new seal evenly without twisting or stretching
• Restore power and water, then run a short cycle to check for leaks

Oven not responding to buttons or features won't activate? This control switch restores reliable operation by opening and closing electrical circuits.

Illuminates your oven interior for visibility while cooking and cleaning. Replace when burned out to restore lighting. Verify fit with your model number.

The Range Lamp Assembly is an OEM part for Frigidaire stoves and ranges. It consists of the halogen light bulb, lens cover, and wiring harness necessary to illuminate the oven cavity. This lamp assembly provides light to the cooking and baking space, making it easier to view food and monitor cooking progress.  

Symptoms of a bad range lamp assembly include:

• The oven light not turning on at all  
• Dim, flickering, or intermittent light
• Burned out or blown light bulb
• Cracks or damage to the lens cover

Causes of failure can be a burned out light bulb, broken wiring, or damage from impact or heat over time. 

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Oven won't reach or hold set temperature? A faulty temperature sensor causes inaccurate heating. This monitor probe ensures consistent cooking results.

Replace your oven temperature probe if your meat thermometer feature isn't working or gives inaccurate readings. Simple plug-in installation in minutes.

Junction box for wall ovens. Installs at the rear electrical connection area. Replace if cracked, damaged, or missing to safely house wiring connections.

The Terminal Block Kit is an OEM part for Frigidaire appliances, typically used for connecting house power to various electrical appliances like ranges and dryers. This kit includes includes screws, nuts, and a unique terminal block. It plays a critical role in the power supply system by providing a reliable connection point for the appliance's main power cord, preventing loose connections and potential electrical hazards.

Symptoms of a bad Terminal Block Kit include:

• Signs of burning or melting at the connection points,
• Flickering power or intermittent operation of the appliance,
• A burning smell from the appliance area.

Causes of terminal block failure often involve loose connections that can lead to arcing and overheating, improper installation, or general wear and tear that degrades the integrity of the electrical contacts.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

If your oven won't heat or heats unevenly, this heating element restores proper temperature control. Straightforward DIY fix for most ranges.

Oven not heating or baking unevenly? This hidden bake element restores proper bottom heat. Moderate DIY repair—requires removing oven racks and panels.

Replace a cracked, damaged, or missing shield in your wall oven or microwave combo. This protective panel installs behind components to prevent wear.

Receptacle block for electric ranges and wall ovens. Mounts in the rear panel to provide electrical connection. Replace if cracked, melted, or damaged.

This evaporator fan motor circulates cold air inside the refrigerator compartment to maintain even cooling and proper airflow. Replaces a failed or noisy fan motor to restore consistent temperature distribution. What it does:

• Spins the evaporator fan blade to move air across the evaporator coils and throughout the fresh-food compartment
• Helps prevent uneven cooling, warm spots, and excessive frost buildup when operating correctly
• Reduces or eliminates grinding, rattling, or humming caused by a worn or failing motor
• Works as part of the refrigerator's airflow system to support normal compressor and defrost operation

• One evaporator fan motor (single unit as shown)

• Disconnect power before servicing to avoid shock or injury
• Access typically requires removing interior panels; handle evaporator fins and wiring with care
• Verify fan blade clearance and secure electrical connectors before restoring power

Decorative trim piece for wall oven installation. Covers gaps between oven and cabinet cutout. Replace if cracked, chipped, discolored, or missing.

Replacement mounting bracket that secures internal oven components. Install when original is cracked, bent, or missing to restore proper alignment and support.

This console cover replaces a damaged or worn dispenser trim to restore a clean, finished look and protect internal dispenser components from spills and debris. It helps maintain dispenser function and appearance. What it does

• Covers and protects dispenser/console components from moisture, food, and everyday wear
• Restores a flush, finished appearance to the dispenser area
• Prevents debris from entering control openings and trim seams
• Can reduce rattles or movement caused by a broken or loose trim piece

• One console cover (trim) as pictured

• Disconnect power to the refrigerator before beginning any work
• Remove any screws or retainers holding the old cover; keep hardware if reusing is intended
• Align the replacement cover carefully and secure with original screws or clips

Fix uneven baking or no convection heating with this electric wall oven fan motor. Powers air circulation for even cooking. Moderate DIY repair.

Loud grinding or rattling from your oven? A damaged convection fan blade disrupts airflow. This replacement restores quiet operation in 20-30 minutes.

This is a nut that is used in many microwave ovens. It is typically used to hold interior fan in place. A nut is a fastener that is used to hold two items together or keep one component secure against a surface. Use and time can cause the nut to become stripped, damaged, or broken. If the nut is broken, it will no longer hold the fan in the right location. The nut will need to be replaced.Before replacing this part, the microwave should be unplugged. Open the refrigerator door and remove the cover that goes over the fan. The nut can then be removed using a nut driver. Replace the other parts before using the appliance.This nut is used in microwave ovens manufactured by Crosley, Electrolux, Frigidaire, and Kenmore. It is sold as a single part. This is an authentic OEM replacement part is sourced directly from the manufacturer.

Oven won't heat after self-cleaning? This high-limit thermostat cuts power when temperatures get too high. Moderately easy DIY repair fix.

Convection fan motor that circulates hot air inside the oven cavity for even cooking temperatures. Replace if fan stops spinning or makes excessive noise during convection baking.

This Tube Assembly routes water inside the refrigerator to the dispenser and ice-maker, restoring proper water flow and preventing leaks when the original line is damaged. Reliable replacement for delivery and fill connections. What it does:

• Transports water from the inlet to the ice maker/dispenser assembly
• Replaces cracked, kinked, or leaking tubing that causes puddles or low water flow
• Helps restore normal ice production and dispenser operation when the tube is the fault
• Matches OEM routing and connector types for correct fit and seal

• One tube assembly as shown

• Disconnect power and shut off the water supply before starting
• Remove ice maker or access panel as needed to reach routing; follow OEM service instructions
• Inspect fittings and replace any damaged clamps or seals; avoid kinking the new tube
• After installation, turn on water, check for leaks, and run dispenser/ice cycles to confirm proper flow

Reinforces and supports oven door glass panels. Replace if original stiffener is bent, cracked, or missing to properly secure glass in the door frame.

Burner won't heat or heats unevenly? This radiant cooktop surface element restores direct heat to one burner, returning reliable cooking performance.

Positions and supports range components to maintain proper alignment. Replace if cracked, broken, or missing to prevent rubbing and ensure panels fit correctly.

The Vent Trim is an OEM part for Frigidaire wall ovens. This trim piece is located along the top front of the wall oven and serves an important functional and aesthetic purpose.

The vent trim facilitates proper airflow and ventilation around the top heating elements and glass door. It ensures heat and gases can safely escape during the cooking process. Over time, high heat exposure may cause damage, discoloration or warping of the original trim piece.

Causes can be standard wear and tear or accidental impact damage. Replacing with this OEM part restores your wall oven's appearance and ventilation system.

Symptoms of a bad front vent trim include:

• Excessive temperatures around the door glass or control panel areas
• Reduced airflow leading to decreased cooking performance
• Visual deformities, cracks or pieces missing from the trim

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Replacement water-line tube that routes water inside the refrigerator to the ice maker or dispenser, helping restore proper water flow and reduce leaks. Designed to match factory routing so the line fits and seals correctly at the connections. What it does:

• Carries water from the cabinet valve to the ice maker or dispenser.
• Restores normal dispenser flow and ice production when the tube is cracked, pinched, or clogged.
• Helps stop visible leaks or pooling caused by damaged or misrouted tubing.
• Matches factory bends for correct routing and clearance behind panels.

• Disconnect power and shut off the water supply before starting any work.
• Remove shelves or panels as needed for access; watch for sharp edges.
• Check and replace any worn clamps or fittings; tighten connections and test for leaks with water on before reassembling.

Mounting screw for electric and gas ranges. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

Secures internal panels or components to the range frame. Replace this mounting bracket if bent, broken, or missing to restore stable support and alignment.

Replacement mounting screw for range power and control boards. Secures electrical board connections. Needed when original screw is missing or damaged.

Hex flange nut with 10-32 thread secures components in appliances. Replace if stripped, missing, or damaged. Flange provides broader bearing surface.

Fix intermittent or failed component operation with this wiring harness assembly. Restores reliable electrical connections between range components.

Wiring harness assembly that routes power and signals between your wall oven's control and components. Replace when harness is damaged or corroded.

Replacement mounting screw for ovens and ranges. Secures panels, brackets, trim, and internal components. Replace missing or stripped screws to restore fit.

Spacer that maintains proper gap between components in your range or oven assembly. Replace if missing, worn, or damaged to restore correct fit and alignment.

Replacement screw secures panels, trim, and internal components in your appliance. Needed when original fastener is missing, stripped, or damaged.

Illuminates your oven interior for visibility while cooking and cleaning. Replace when burned out to restore lighting. Verify fit with your model number.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.