Bosch Washer Parts

The door boot gasket is the flexible rubber seal between the washer's front tub and the door opening. It keeps wash water contained during cycles and helps prevent drips and leaks at the front of the machine. What it does

• Forms a watertight seal between the outer tub and the door opening
• Helps prevent leaks and water on the floor during and after cycles
• Restores proper sealing when the original gasket is torn, deformed, or moldy
• Common symptoms: water leaking from the door, visible rips, musty odors, or a door that won't seal properly

• Includes: 1 door boot gasket

• Unplug the washer and turn off both water supplies before servicing
• Remove the outer retaining band/clamp and release the old gasket from the front panel
• Access and remove the inner clamp; note gasket orientation, then remove the old gasket from the tub lip
• Fit the new gasket fully onto the tub, reinstall inner and outer clamps, and test for leaks before reassembly

This dual water inlet valve controls water flow to appliance components like the dispenser and ice maker, restoring proper water delivery when the valve is functioning. It replaces a faulty or leaking inlet valve to help stop water issues. What it does:

• Opens and closes water flow to the appliance's water circuits (dispenser/ice maker) when signaled
• Commonly linked to no water dispensed or ice maker not filling
• Can be a source of slow fill or intermittent water delivery
• A leaking or stuck valve can cause visible leaks or water pooling

• One dual water inlet valve

• Shut off water supply and disconnect power before servicing
• Use basic hand tools; avoid overtightening connections to prevent damage
• Inspect inlet hoses and seals when replacing the valve

This rear drum motor mounting bushing supports the motor shaft at the back of the tub, keeping the drum aligned and reducing wear. It restores smooth drum rotation and helps reduce noise and vibration when functioning properly. What it does:

• Centers and supports the motor shaft to maintain proper drum alignment.
• Cushions rotating components to reduce squealing, grinding, or scraping noises.
• Helps prevent excess drum wobble and uneven wear on the tub and bearings.
• Can stop intermittent rubbing or burning smells caused by a worn mounting surface.

• Disconnect power before starting and follow all safety precautions; service panels may have sharp edges.
• Access typically requires removing the dryer/heater assembly and drum.
• Inspect mating surfaces and surrounding components (shaft, bearing, seal). Replace any excessively worn parts to prevent repeat failures.
• Use only OEM-recommended parts and fasteners; do not force or press the part in without proper alignment.

This dishwasher sump assembly houses the pump inlet and integrated ball check valve to route wash water to the drain while preventing backflow. Replaces worn or cracked sumps to restore proper draining and prevent leaks. What it does

• Collects and channels dishwasher wash water from the tub to the drain pump.
• Integrated ball check valve stops backflow into the sump, helping prevent standing water and odor.
• Restores proper drain function when the existing sump is cracked, clogged, or leaking.
• Compatible with common Bosch/BSH dishwasher pump systems that use a molded sump with ball valve.

• One sump with integrated ball check valve (single assembly only).

• Disconnect power and water supply before starting any repair.
• Access typically requires removing the dishwasher lower kickplate and possibly tilting the unit; support the unit and follow the OEM service manual.
• Inspect surrounding seals, hoses, and pump gaskets for wear and replace as needed.

This water level regulator controls the appliance's water fill by sensing and regulating pressure/level for proper operation. Replacing a failing regulator restores correct fill behavior and helps prevent over- or under-fill conditions. What it does:

• Senses water level/pressure and signals the fill system to start or stop water flow
• Prevents overfilling by stopping the inlet when the correct level is reached
• Helps avoid underfilling that can cause poor wash or rinse performance
• Resolves symptoms like continuous filling, no fill, or erratic water levels

• Water level regulator

• Disconnect power and turn off the water supply before attempting replacement
• Handle electrical connections and hoses carefully; note wiring positions for reassembly
• Inspect hoses and seals for damage and replace if cracked or brittle
• Test the appliance through a short cycle after installation to ensure proper fill and operation

This fastening ring secures a rotating or stationary component in place to help prevent movement and vibration. It restores proper fit and alignment so assemblies run quietly and components stay locked in position. What it does:

• Holds shafts, bearings or housings in position to prevent axial movement
• Helps stop rattling, wobble or misalignment caused by a loose retaining component
• Maintains a secure mechanical connection between mating parts
• Used wherever a snap/retaining ring is required to lock a component on a shaft or in a bore

• Disconnect power and water before beginning any repair
• Use the correct pliers or tools for snap/retaining rings to avoid deformation
• Verify the ring matches the OEM part number and seating location before installation