Parts for Whirlpool WED85HEFC2: Bulkhead Parts

Shaft that secures front drum support rollers in your dryer. Replace if worn, scored, or damaged to restore proper drum alignment and support.

This screw is used to secure the handle end cap to the center of the door. The screw size measures 8-18 x 1/2 inches.

Houses the lint screen in your dryer. Replace if cracked, broken, bent, or damaged. Ensures proper lint screen fit and secure installation.

Dryer won't start or stops mid-cycle? A faulty sensor wire harness disrupts temperature readings. This direct-fit harness restores accurate communication.

This air duct directs airflow inside the appliance to help maintain proper ventilation and cooling. Replacing a damaged duct restores correct air movement and can reduce noise or uneven temperature issues. What it does:

• Channels warm or cool air through the appliance's ventilation path
• Prevents air leaks that can cause unusual noises or reduced performance
• Helps maintain consistent internal temperatures and component cooling
• Supports connected seals and ducts to ensure efficient airflow

• Disconnect power before servicing to avoid shock or injury
• Inspect surrounding seals and fasteners; replace any that are worn or broken
• Handle carefully to avoid cracking plastic tabs during removal/installation

Genuine dryer seal creates a tight barrier to prevent air leaks. Replace if worn, cracked, or causing poor drying performance. Confirm fit with your model.

Seals the drum perimeter to prevent abrasion and maintain temperature. Replace when worn, torn, or causing marks on clothes. Verify fit by model number.

Replacement outer access cover for dryers. Protects internal components and maintains a finished appearance. Needed when original is cracked or missing.

This blower housing assembly replaces the blower chamber that supports the blower wheel and routes air through the dryer for proper tumbling and drying. Restores correct airflow and helps reduce overheating or poor drying performance. What it does:

• Houses and supports the blower wheel to direct airflow from the drum to the exhaust.
• Ensures proper airflow for consistent drying and venting.
• Can address symptoms like weak airflow, long dry times, or unusual blower noise when damaged or cracked.
• Works with the blower wheel and motor to maintain lint passage and exhaust flow.

• Disconnect power before inspecting or replacing the blower housing; follow manufacturer safety procedures.
• Access may require removing the dryer front or rear panel depending on model.
• Inspect the blower wheel and motor for damage or obstructions while replacing the housing.

This cover mounts inside the dryer and shields the drum light from direct contact with tumbling clothes. It helps protect the light bulb and prevents garments from snagging on the light assembly. Replace this cover if it is cracked, melted, missing, or if clothes are catching near the light area during drying cycles.

Connects and secures the exhaust duct to your dryer. Replace if the collar is cracked, loose, damaged, or missing to restore a tight vent connection.

Dryer clip secures internal components and prevents rattling or loose parts. Replace if broken, missing, or worn to restore proper fit and function.

Dryer not heating or clothes coming out damp? The heating element generates heat to dry clothes. DIY-friendly repair in about 30-45 minutes.

Connects power to your dryer's heating element. Replace this wire if it's frayed, burned, corroded, or broken to restore the electrical connection.

This 3/8-16 nut secures appliance components and helps prevent loosening and vibration. Replace a worn, stripped, or missing nut to restore a tight, reliable connection and consistent operation.

• Provides a 3/8-16 threaded fastener connection for applicable bolts or studs
• Helps keep brackets, panels, and other parts firmly in place
• Replaces damaged or missing hardware that can cause looseness or rattling
• Signs of failure include rounded corners, stripped threads, corrosion, or inability to tighten securely

• Disconnect power and, if applicable, shut off water and gas before servicing
• Match thread size to the original part; start threading by hand to avoid cross-threading
• Reinstall any washers/spacers in the original order; tighten securely without over-tightening
• If the original used a locking feature or threadlocker, reinstall per your product's service information

The washer is an OEM replacement part for Whirlpool clothes dryers. This part is located on the drum roller support shaft in your dryer. The exterior of the washer is 1 inch in diameter with a hole in the middle and is made of metal. They are installed alongside the drum support rollers and idler pulleys. They help prevent the rollers and pulleys from bumping up against the brackets they are installed on. If you are replacing the rollers, we suggest you replace the washers at the same time.

Causes can be normal wear to bearing surfaces over extended use cycles. Accidental impacts may also potentially bend or damage shaft components.

Symptoms of a bad roller shaft include:

• Noisy squeaks or clanks emanating from within
• Jerky or unbalanced tumbling of dryer loads
• Roller assemblies binding or sticking

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

The Drum Support Shaft for Left Hand Threads is an OEM replacement part for Whirlpool dryers. This component is essential for securing and supporting the drum as it rotates during the drying cycle. It helps maintain the drum’s alignment and stability, ensuring smooth and efficient operation of the dryer.

Over time, the drum support shaft can become worn out or damaged due to continuous use, the weight of laundry loads, or improper installation. Additionally, exposure to high temperatures and repeated mechanical stress can cause the shaft to weaken or fail, leading to issues with the dryer’s performance.

Symptoms of a bad drum support shaft include:

• The drum not rotating smoothly or making grinding noises
• Excessive wobbling or vibrating of the drum during the drying cycle
• The dryer taking longer to dry clothes or not drying them evenly
• Visible damage or wear on the shaft or its threads
• The drum becoming misaligned or not sitting properly within the dryer

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Secures drum support rollers to their shafts in your dryer. Replace if broken, missing, or damaged during roller maintenance to keep drum wheels stable.

Replacement drum support roller for dryers. Mounts on the drum frame to support and guide the drum as it rotates. Replace if cracked, worn, or damaged.

Channels hot air from your dryer to the vent system. Replace this exhaust pipe if the original is cracked, damaged, or leaking to restore airflow.

Replacement lint screen filters debris to maintain airflow and prevent clogs. Replace when torn, damaged, or worn. Confirm fit with your model number.

Seals the blower housing to prevent air leaks that reduce drying efficiency. Replace if worn, cracked, or missing to restore optimal airflow.

Replacement drum for your dryer. Main rotating cylinder that tumbles clothes during drying. Order a new drum if yours is cracked, dented, or damaged.

Front drum felt seal prevents clothes from catching between the drum and dryer interior. Replace if worn or damaged. Confirm fit with your model number.

This 8-18 x 5/8-inch screw secures dryer panels, brackets, and covers. Replace missing or stripped fasteners to restore a tight fit and stability.

Channels exhaust air and traps lint in your dryer. Replace if damaged, clogged, or airflow is restricted. Confirm fit with your model number.

Fix a dryer that won't start or has no heat with this thermal fuse. This safety component prevents overheating. Easy 30-minute DIY repair.

Dryer shuts off before clothes are dry? The moisture sensor bar detects dryness levels. Easy 10-30 minute DIY fix with video guide included.

This cable tie secures wiring and the power cord to the appliance chassis to help prevent chafing, pinching, or loose connections. Simple, low-cost part that restores proper wire routing and strain relief. What it does

• Holds wiring and harnesses in place to prevent rubbing against sharp edges
• Helps reduce risk of intermittent power or connector strain caused by loose wires
• Keeps harnesses routed for correct clearance and component access
• Useful during repairs to restore original wire routing and strain relief

• One cable tie (wire harness retainer)

• Safety first: disconnect the appliance from power before inspecting or replacing wiring components
• Remove the damaged or existing retainer and route harnesses to match original OEM routing before installing the new tie
• Trim excess tie tail; do not overtighten—secure, but avoid crushing wires
• Replace any tie that's melted, cracked, or otherwise damaged rather than reusing it

Fix E1 error codes or overheating issues with this dryer thermistor. Monitors temperature to prevent shutdowns. DIY repair takes about 30 minutes.

Dryer making rattling noise or not heating properly? A cracked blower wheel disrupts airflow. Moderate DIY repair—requires panel removal and wrench work.

Secures the heater housing to the dryer cabinet. Replace if your bracket is bent, cracked, or missing to restore stable mounting and alignment.

This is the exterior air grille that covers the dryer's exhaust outlet, directing warm, moist air out of the appliance. It helps protect internal components and maintain proper airflow during the drying cycle. Replace this grille if it is cracked, warped, or has broken louvers that could restrict airflow and reduce drying performance.

Replacement screw for dryers. Secures panels, brackets, and internal components. Replace if missing, stripped, or corroded to eliminate rattles.

Dryer drum support pad provides cushioning and reduces noise during operation. Replace if worn, cracked, or causing rattling sounds. Confirm fit with your model.

The Dryer Thermostat is an OEM part for Whirlpool dryers. It regulates the temperature inside the dryer, ensuring that it maintains the correct heat levels for safe and efficient drying cycles.

You should replace this dryer thermostat if it becomes faulty. Common causes of a bad dryer thermostat include electrical failures, buildup of lint or debris causing overheating, and general wear and tear over time.

Symptoms of a bad dryer thermostat include:

• Dryer overheating or not heating at all
• Extended drying times
• Dryer shutting off prematurely
• Error codes related to temperature control

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Molded protective cover that shields internal dryer components from moisture and debris. Replace if cracked, broken, or missing to maintain proper protection.

Dryer not heating? A warped or damaged heater box lets heat escape, reducing efficiency. This housing secures the element and protects components.

If your dryer's steam function isn't working or you hear unusual noises during the steam cycle, the water inlet valve may be clogged or faulty.

Replaces a cracked, broken, or missing drum baffle in your dryer. This internal tumbler fin lifts and tumbles clothes during the drying cycle.

This kit includes a thermal cut-off fuse and a high limit thermostat that work together to protect your dryer from overheating. They are typically mounted on or near the heating element housing and will shut off the heater if temperatures exceed safe limits. Replace this kit if your dryer runs but produces no heat, or if the thermal fuse has blown due to a clogged vent or restricted airflow.

Front bulkhead for your dryer drum assembly. Replace this structural component if it's cracked, damaged, or worn to restore proper drum support.

Retainer clip secures interior panels and trim in your dryer, reducing vibration and rattling. Replace when panels feel loose or fasteners break.