Parts for Electrolux EIMGD60LT3: 06 - Burner Parts

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This mounting bracket secures internal components to the appliance chassis, restoring proper alignment and stability. Replaces a broken or bent bracket to stop loose parts, rattling, or misaligned panels for safer, quieter operation. What it does:

• Provides a rigid attachment point for panels, assemblies, or hardware to the cabinet or frame
• Prevents movement that can cause rattling, scraping, or uneven gaps
• Restores correct alignment so related parts operate smoothly
• Helps maintain safe spacing and support for adjacent components

• One mounting bracket as shown

• Disconnect power (and water, if applicable) before installing
• Handle metal edges carefully; wear gloves to avoid cuts
• Use the existing fasteners when possible; replace damaged screws if needed

A single replacement screw used to secure appliance trim, panels, or interior components. Replaces lost or damaged fasteners so panels and assemblies stay firmly attached and appliances operate safely. What it does:

• Secures trim pieces, control panels, brackets, or interior components
• Restores proper fit and alignment when panels are loose or rattling
• Helps eliminate vibration noise caused by missing or stripped screws
• Used wherever the OEM screw specification is required for reliable fastening

• Install with the matching screwdriver or driver bit; avoid over-tightening to prevent stripping
• Disconnect power and remove or support panels as needed for safe access
• If screw threads are damaged, replace with the exact OEM screw to ensure secure fit

The Outlet Thermal Fuse is an OEM part for Frigidaire dryers. It acts as a safety device that protects the dryer from overheating by cutting off the power if the temperature exceeds a safe level. This ensures the dryer operates safely and helps prevent potential fire hazards.

Causes of a bad thermal fuse can include lint buildup blocking airflow, overloading the dryer, or mechanical failures in the heating element. These issues can cause the dryer to overheat, leading to the fuse blowing as a protective measure.

Symptoms of a bad outlet thermal fuse include:

• The dryer not starting
• The dryer running but not heating
• Sudden stopping during a cycle
• No power to the dryer

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Thermostat is an OEM replacement part for Frigidaire dryers. It plays a crucial role in monitoring and regulating the temperature inside the tumbler. The thermostat works closely with the heating element and controls to accurately sense temperature fluctuations and modulate heating levels accordingly.

Symptoms of a bad thermostat include:

• Clothes taking an overly long time to dry
• The dryer is heating excessively and tripping the breaker
• Temperature display or heater lights not functioning
• Clothes drying unevenly, still damp in spots

Causes can be normal wear over extreme heating and cooling cycles. Environmental contaminants may also impact sensor performance.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This electrical wiring harness connects and routes power and signals between fridge components, restoring reliable electrical continuity so controls, lights, and motors can operate correctly. Use this direct-replacement harness to repair damaged or worn wiring. What it does

• Routes power and signal connections between control boards, compressors, valves, lights, and sensors
• Restores lost or intermittent electrical connections that can cause controls to fail or components to stop working
• Prevents shorts and open circuits when damaged wires or broken connectors are replaced
• Matches OEM connector types and wire lengths for a direct-replacement fit

• One electrical harness

• Disconnect power at the breaker or unplug the appliance before inspecting or replacing the harness
• Compare connector shapes and wire colors to the original harness to ensure correct installation
• Secure wires away from moving parts and sharp edges; avoid pinching or excessive bending

This genuine OEM replacement part is a gas valve assembly for dryers. The burner and gas valve assembly is a complete assembly that contains the burner that distributes the gas in a way that creates an even flame allowing for heat to be distributed properly to perform the dryer's essential functions. If the dryer is no longer drying clothes effectively, or heating properly, then it might be time for it to be replaced. Luckily repairing a gas valve assembly is an easy fix.To replace the burner and gas valve assembly, begin by shutting off power to the appliance. Next, pull the dryer away from the wall to gain access to the back panel. Remove the back panel and locate the gas valve assembly. Remove the mounting screws that hold it in place. After removing the screws use both hands to pull and release the old valve assembly. Set it off to the side and proceed to install the new one by refastening the screws that hold it in place.This replacement part is sold individually and is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand washers.

The Dryer Gas Valve Coil Kit is an OEM part for Frigidaire dryers. This kit includes solenoid coils necessary for the opening and closing of the gas valve during the drying cycle. These coils are vital for controlling the flow of gas into the burner, enabling the ignition and maintaining the flame required to dry clothes effectively. 

Symptoms of a bad Dryer Gas Valve Coil Kit include:

• No heat or insufficient heat in the dryer.
• The dryer stops heating partway through the cycle.
• A "clicking" noise when the dryer attempts to ignite the gas flame but fails.
• Gas smell from the dryer, indicating incomplete combustion.

Causes of a bad coil kit can include electrical failure within the coils, mechanical wear from repeated use, or overheating that damages the coil's integrity.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Dryer Gas Valve Coil Kit is an OEM part for Frigidaire dryers. This kit includes solenoid coils necessary for the opening and closing of the gas valve during the drying cycle. These coils are vital for controlling the flow of gas into the burner, enabling the ignition and maintaining the flame required to dry clothes effectively. 

Symptoms of a bad Dryer Gas Valve Coil Kit include:

• No heat or insufficient heat in the dryer.
• The dryer stops heating partway through the cycle.
• A "clicking" noise when the dryer attempts to ignite the gas flame but fails.
• Gas smell from the dryer, indicating incomplete combustion.

Causes of a bad coil kit can include electrical failure within the coils, mechanical wear from repeated use, or overheating that damages the coil's integrity.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This burner orifice meters gas to a range/cooktop burner through a calibrated opening. Replacing a clogged, damaged, or incorrect-size orifice helps restore proper flame height and clean, consistent combustion for reliable cooking performance.

• Regulates fuel flow to the burner via the precisely sized orifice opening
• Helps address weak/uneven flame, yellow or sooty flame, or delayed ignition
• Replaces stripped, blocked, or wrong-size orifice spud
• Size- and position-specific—match the stamped size and location

• Disconnect electrical power and shut off the gas supply before servicing
• Allow the cooktop to cool; remove grates, caps, and burner head to access the orifice holder
• Use the proper orifice/nut driver; do not overtighten or alter/enlarge the opening
• After reassembly, restore gas and leak-test with an approved solution; verify a stable blue flame and adjust air shutters if applicable

This glow-bar igniter lights the gas burner in your dryer so it can produce heat. When the igniter is cracked, weak, or open, the burner won't light and clothes won't dry properly.

• Heats up to ignite the gas burner during each heating cycle
• Common symptoms of failure: no heat, takes too long to dry, burner won't light, igniter doesn't glow or glows but no flame
• Restores consistent ignition and drying performance

• Unplug dryer and shut off gas supply before servicing
• Handle the igniter carefully—ceramic element is fragile; avoid touching it with bare fingers
• Note wire routing and burner alignment before removal
• After installation, restore gas/electric and check for proper burner ignition

This is a replacement mounting collar used to secure and align associated appliance components for proper fit and operation. It restores the original spacing and support where the factory collar is worn or damaged. What it does:

• Provides a secure mounting point to hold panels, assemblies, or shafts in correct alignment
• Helps prevent excess movement that can cause noise, vibration, or premature wear
• Restores proper spacing to prevent rubbing or binding of adjacent parts
• Useful when a cracked, deformed, or missing collar causes misalignment or rattling

• Always disconnect power to the appliance before beginning repairs to avoid shock or injury
• Inspect surrounding parts and mounting hardware; replace any damaged fasteners for a secure fit
• Hand-start fasteners to avoid cross-threading, then tighten to OEM torque if specified

This burner assembly restores proper gas flame and heat in your dryer. It directs and mixes gas and air for clean ignition at the igniter, helping clothes dry efficiently and consistently.

• Provides the flame path and mixing chamber for gas ignition
• Helps resolve symptoms like no heat, intermittent heat, or very long dry times
• Can address issues where the burner won't ignite or the flame will not stay lit
• Designed to fit the factory burner mount and align with the igniter and flame sensor

• Disconnect power and shut off gas supply before servicing; allow the appliance to cool
• Access is typically from the front lower panel or burner compartment
• Transfer any reusable hardware from the original assembly if required
• After reassembly, restore gas and check all connections for leaks using a soapy water solution

This electrical wiring harness routes power and signals between components to restore reliable electrical connections. It replaces a damaged or worn harness to correct intermittent power, nonresponsive controls, or component failures. What it does:

• Carries electrical power and control signals between appliance modules and components
• Restores lost or intermittent electrical continuity caused by frayed wires or broken connectors
• Helps resolve symptoms like lights or components not powering on, sporadic operation, or control failures
• Maintains factory routing and connector fit for proper electrical performance

• Disconnect power before attempting any repair to avoid shock or damage
• Compare connectors and wire colors to the old harness to ensure correct replacement
• Use proper strain relief and routing to prevent chafing or pinching of wires

The Dryer Heat Sensor is an OEM part for Frigidaire dryers. This sensor monitors the temperature inside the dryer drum to ensure clothes are dried effectively and safely by regulating the heat levels during the drying cycle.

Causes of a bad heat sensor can include wear and tear from frequent use, buildup of lint or debris, or electrical issues. A malfunctioning sensor can result in incorrect temperature readings, leading to under-drying or overheating of clothes.

Symptoms of a bad Dryer Heat Sensor include:

• Clothes not drying properly or taking too long to dry
• Dryer overheating or shutting off unexpectedly
• Inconsistent drying cycles
• Error codes related to temperature control

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement tube routes defrost melt and condensation away from the freezer compartment to the drain pan, helping prevent leaks and ice buildup. Fits specific Frigidaire refrigerator models—check product fit for compatibility. What it does:

• Channels defrost water from the evaporator area to the drain system to prevent pooling
• Helps stop ice accumulation that can block drains and reduce cooling efficiency
• Restores proper water flow when original tube is cracked, split, or clogged
• Compatible direct-replacement when matched to the appliance model/PN

• Disconnect power before starting any repair to avoid electrical shock
• Use appropriate clamps or retainers from the appliance as originally installed; replace damaged clips if needed