Parts for Kenmore 791.783889 (791783889, 791 783889): Burner Parts

Gas burner won't light or clicks but doesn't ignite? Replace the igniter switch to restore spark and reliable lighting. Simple 15-30 minute DIY fix.

This ferrule is a small compression fitting used to secure and seal a refrigerator water line connection, helping stop leaks and maintain proper flow to the ice maker or dispenser. It's a simple replacement to restore a tight water connection. What it does:

• Secures tubing to a compression or shutoff fitting to prevent leaks at the connection
• Restores a proper seal for water supply lines feeding the ice maker or dispenser
• Commonly used when a loose, dripping, or leaking water line is present
• Helps prevent water damage from failing or corroded fittings

• One ferrule

• Turn off the water supply and relieve line pressure before servicing
• Confirm tubing is cut square, fully inserted, and the ferrule is seated before tightening
• Tighten fittings per manufacturer guidance; avoid over-tightening which can damage tubing
• After installation, turn water back on and check carefully for leaks

Cable retainer for cooktop installation. Secures wiring harnesses in place. Replace if broken, cracked, or missing to properly organize internal cables.

This part has been discontinued by the manufacturer and is no longer available.

This elbow is a threaded pipe fitting that redirects and secures a fluid line connection where space or alignment requires a 90° turn. It provides a compact, threaded junction to connect compatible appliance tubing or hose to a valve or port. What it does:

• Connects two threaded line ends at a 90° angle for tight routing in confined spaces
• Provides a sealed, threaded junction between a 1/2 in. NPT inlet and a 9/16-24 threaded outlet
• Helps stop leaks and maintains proper line alignment when the original elbow is worn or damaged
• Commonly used where a bent or cramped connection prevents a straight coupling

• One elbow fitting (1/2 in. NPT x 9/16-24)

• Turn off and depressurize the water supply (or system) before removing or installing fittings
• Start threads by hand to avoid cross-threading; tighten with appropriate wrench until snug
• Use plumber's tape or thread sealant only if specified by the appliance manufacturer

The pressure regulator with bracket controls gas flow to the range burners and is typically located behind the range. Replace when burners won't light, flame is irregular, or you smell gas during operation.

Oven won't light even though igniter glows? Burner lights only when valve is tapped? Replace the dual gas safety valve. DIY install in under 1 hour.

Oven won't light or ignites with a loud pop? A faulty igniter is usually the cause. Simple DIY fix—disconnect two screws and wire nuts to replace.

By Frigidaire. 2+0 module type. Employs two spark electrodes for manual surface ignition of a four burner range top with flash tubes to front and rear burners. Very popular module used on many different brands and models. Check by appliance model number, if not sure.

Mounting bracket that secures the gas pressure regulator to your range frame. Replace if bent, broken, or missing to properly support the regulator assembly.

This part has been discontinued by the manufacturer and is no longer available.

This upper burner retainer secures the surface burner head and helps keep the burner aligned for even flame distribution and reliable ignition. It's a small replacement part that restores proper burner positioning. What it does:

• Holds the upper surface burner head in place on gas cooktops and ranges
• Keeps the burner aligned so the flame and heat pattern are consistent
• Helps prevent burner wobble that can cause ignition issues or uneven cooking
• Compatible with original mounting points and hardware on compatible Frigidaire ranges

• One retainer — burner upper

• Disconnect gas supply and power to the appliance before working on burners; follow appliance manufacturer safety instructions
• Remove burner cap and head, replace the retainer, then reassemble in the original order
• Check burner alignment and ignition after reassembly; if you smell gas or see irregular flame, stop and inspect

This part has been discontinued by the manufacturer and is no longer available.

Rubber bumper that cushions the range door or drawer when closing. Replace if cracked, worn, or missing to prevent rattling and protect surfaces.

Replace your gas range's damaged or missing oven front cover. This cosmetic panel installs on the front of the oven cavity to restore appearance.

This light box is the interior lamp housing that secures the refrigerator light and helps direct illumination inside the compartment for better visibility. It replaces cracked, broken or yellowed housings to restore safe mounting for the lamp. What it does:

• Holds and protects the interior light socket and bulb assembly
• Directs and diffuses light for even interior illumination
• Prevents loose or exposed wiring near the lamp area
• Addresses symptoms like a cracked or missing housing, rattling near the light, or reduced/diffuse lighting due to a damaged cover

• Disconnect power to the appliance before starting any work
• Usually removes with a screwdriver or by releasing plastic tabs—keep track of fasteners
• Avoid touching the bulb with bare hands; replace bulb if damaged

This adhesive identification label replaces a torn, faded or missing appliance sticker so model, serial or safety information is legible again. It helps you confirm appliance details for service, parts or safety checks. What it does:

• Restores readable model/serial and specification information that is printed on the original sticker
• Replaces damaged or faded identification and safety labels
• Makes it easier to verify the correct part or service information before repair
• Helps meet safety and inspection needs by restoring visible manufacturer info

• One adhesive identification label

• Clean and dry the mounting area before applying to ensure good adhesion
• Peel backing and press label firmly; hold for several seconds to set
• Avoid placing on textured or insulated foam surfaces where adhesion may be poor

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

Secures the oven bottom panel in place. Replace if screw is stripped, missing, or no longer holds the panel securely. Sold individually.