Parts for Kenmore 363.71542 (36371542, 363 71542): Cabinet (5 Parts

Size: 8 - 18 ab.

Mounting screw hardware for ranges and cooktops. Replace missing, stripped, or corroded screws used to secure panels, brackets, or components.

Mounting screw for laundry center units. Secures panels and components inside the cabinet. Replace if stripped, missing, or damaged during repairs.

Replacement hex washer head screw for laundry center panels and components. Needed when original fasteners are stripped, missing, or damaged during repair.

This SCR (silicon controlled rectifier) is a replacement power-control semiconductor used in appliance circuits to switch and regulate current. It restores proper control of heater/motor circuits when the original SCR fails. What it does:

• Controls current flow in high-power appliance circuits for timed heating or motor control.
• Replaces a failed SCR that causes intermittent or no power to the controlled component.
• Common symptom: appliance elements or motors do not turn on or cycle correctly.
• Common symptom: visible burn, cracking, or open circuit at the SCR.

• Disconnect power to the appliance before accessing electrical components to avoid shock.
• Handle the SCR carefully to avoid static or mechanical damage; use original mounting and hardware.

This SCR (silicon controlled rectifier) is a replacement power-control semiconductor used in appliance circuits to switch and regulate current. It restores proper control of heater/motor circuits when the original SCR fails. What it does:

• Controls current flow in high-power appliance circuits for timed heating or motor control.
• Replaces a failed SCR that causes intermittent or no power to the controlled component.
• Common symptom: appliance elements or motors do not turn on or cycle correctly.
• Common symptom: visible burn, cracking, or open circuit at the SCR.

• Disconnect power to the appliance before accessing electrical components to avoid shock.
• Handle the SCR carefully to avoid static or mechanical damage; use original mounting and hardware.

A single replacement screw used to secure appliance panels, trim, and internal brackets so components stay aligned and reduce rattling. Simple, direct-fit fastener for restoring proper mounting and stable operation. What it does:

• Secures panels, mounting brackets, trim pieces and other appliance components
• Helps stop rattling, vibration, or loose panels caused by missing or stripped fasteners
• Restores proper alignment of doors and access panels when original screw is lost or damaged
• Matches the OEM fastening point for a straightforward hardware replacement

• Disconnect power to the appliance before working on electrical components or access panels
• Use the correct screwdriver to avoid stripping the head; match drive type to the screw
• Tighten firmly but do not overtighten—stop when snug to avoid damaging threads or parts
• Keep removed fasteners organized and compare with the replacement to ensure correct fit

Front upper brace for laundry center units. Secures and supports the front panel assembly. Replace if cracked, bent, or broken to restore stability.

Adjustable leveling leg that threads into the base of your laundry center. Replace if broken, cracked, or missing to keep the unit stable and level.

Secures components inside your washer to prevent movement, loose connections, and rattling noise. Replace when worn or missing to restore stability.

Hose cover cap for laundry center units. Covers and protects hose connections. Replace if cracked, broken, or missing to prevent leaks and damage.

Replacement alignment pin for laundry center hinge or latch assemblies. Restores proper positioning of moving parts when original is broken, worn, or missing.

Top panel cover for laundry center units. Installs over the control area to provide a finished appearance. Replace if cracked, chipped, or missing.

Bracket assembly kit for laundry centers. Secures internal components in place. Replace if brackets are bent, cracked, or missing during repairs.

Fix bleach pooling or uneven dispensing in your laundry center. This funnel directs bleach into the wash tub, preventing spills and odor issues.

Washer won't spin or shows flashing lights? This door lid lock ensures safe operation by securing the lid during cycles. DIY-friendly, 2-screw install.

Spring bracket for laundry center units. Secures and supports internal spring assembly. Replace if bracket is bent, cracked, broken, or missing.

Replacement clip cover that snaps over mounting clips to conceal hardware on your washer dryer combo. Restores finished appearance when original is cracked or missing.

Replacement door hinge bushing for laundry centers. Restores smooth pivot operation when original is worn, cracked, or causes door misalignment or sticking.

This is the top lid for a washer or laundry center unit. It covers the wash drum and engages the lid switch to allow the machine to operate. Replace this part if the lid is cracked, warped, or broken, which can prevent the washer from starting or completing its cycle.

This lid actuator engages the washer's lid switch or lock when the lid closes, signaling the control that it's safe to run. Replacing a worn or broken actuator restores reliable lid detection for wash and spin cycles.

• Engages the lid switch/lock when the lid is closed
• Signals the control to allow the washer to start and spin
• A damaged or missing actuator can lead to "lid open" errors
• Common symptoms include won't start, won't spin, or lid lock light flashing

• Disconnect power before servicing
• Access the lid switch/lock area; remove the failed actuator
• Install the new actuator, aligning it to the original mounting points; reuse existing hardware
• Close up and test lid detection before running a full cycle

Washer won't start or spin? This lid lock magnet triggers the safety sensor to confirm the lid is closed. Simple DIY fix restores normal operation.

This right-hand hinge washer cover protects and conceals the hinge area on the washer lid, restoring a finished appearance and preventing dirt or moisture from contacting the hinge assembly. What it does:

• Covers the right-side hinge/washer area to keep debris and moisture out of the hinge assembly
• Helps maintain proper lid alignment and reduces exposed sharp edges
• Restores the washer's cosmetic finish after damage or wear
• Can eliminate rattling or rubbing caused by a missing or broken cover

• One right-hand hinge washer cover

• Disconnect power to the appliance before starting any repair
• Remove the washer lid or access panel per the manufacturer's instructions to reach the hinge area
• Fasten the cover using the original screws/clips; do not force or overtighten plastic tabs
• If other hinge components are damaged or loose, inspect and replace as needed for a safe repair

This lid bumper cushions the lid of your top-load washer as it closes, absorbing impact to reduce slamming noise and protect the top panel's finish. Replace a worn or missing bumper to restore smooth, quiet lid operation. What it does

• Absorbs impact between the lid and cabinet to reduce slamming and vibration noise
• Helps protect the top panel finish from chips and scratches near the lid area
• Restores proper cushioning when the original bumper is missing, cracked, or flattened
• Common symptoms: lid slams or clunks when closing, increased noise, visible missing bumper

• 1 lid bumper

• Disconnect power before servicing
• Open the lid and pull the old bumper straight out of its mounting hole; needle-nose pliers can help if it's stuck
• Clean the hole and surrounding surface for a secure fit
• Press the new bumper fully into the hole until seated flush; for even cushioning, consider replacing both if your model uses two

Left-side hinge cover for laundry center washer lids. Restores appearance and protects hinge assembly. Replace if cracked, broken, or missing.

This spring cover protects and retains a mechanism spring inside your washer. Replacing a cracked or missing cover helps keep the spring seated, limits debris intrusion, and supports smooth, reliable movement of the associated control, latch, or linkage.

• Shields the spring and helps keep it properly seated in its pocket
• Reduces friction and wear that can lead to premature spring failure
• Supports consistent return action for the related control, latch, or lever
• Typical symptoms include a missing/broken cover, exposed spring, rattling, or erratic operation

• Unplug the appliance and turn off water before servicing
• Access point varies by model; photograph spring/cover orientation before removal
• Control the spring during disassembly to prevent sudden release
• Ensure the cover is fully seated; test operation before final reassembly

Replaces damaged or worn control panel face on laundry centers. Restores front appearance and provides secure mounting for controls. Needed when cracked or broken.

Retaining clamp secures hoses and tubes to prevent leaks and loose connections in your washer dryer combo. Replace if worn or damaged. Verify fit with model.

The Dual Coil Water Valve is an OEM replacement part for GE washing machines. It is a solenoid valve that controls the flow of hot and cold water to the washer.

Symptoms of a faulty valve include: 

• Failure to adequately fill or drain the wash tub
• Imprecise washing from too much or too little water  
• Oversudsing or excess vibration due to unbalanced levels

Causes can be worn seals or mineral buildup impeding proper valve movement after extended use.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This is a water inlet assembly that directs water flow into the washer tub during the fill cycle. It connects to the water supply line and ensures proper water distribution inside the drum. Replace this part if you notice water leaking near the tub inlet, uneven filling, or water spraying in the wrong direction during a wash cycle.

Secures hoses in your laundry center. Replace if leaking, loose connections, or visible corrosion occur. Verify fit with your model number before ordering.

Secures the drain boot or hose to the washer tub outlet to prevent leaks and separation. Replace if leaking or hose detaches. Confirm fit with model.

Internal drain hose routes wastewater through the washer drain path. Replace if cracked, kinked, or leaking to prevent water damage to floors and components.

Secures wiring and hoses in your laundry center to prevent rubbing and wear. Replace when broken or missing to maintain proper routing. Verify fit.

Drain hose assembly routes wastewater from the washer pump to your standpipe or laundry tub. Replace if cracked, kinked, leaking, or causing floor puddles.

Fix a washer that won't drain or leaves standing water. This drain pump removes water from the drum during drain and spin cycles. Moderate DIY repair.

This washer motor run capacitor stores and releases electrical energy to help the drive motor start and run smoothly. Replacing a weak capacitor can help restore consistent agitation and spin and reduce motor humming or stalling under load.

• Provides the phase shift and torque assist the drive motor needs to start and stay running
• Can address: washer won't start, no agitate or spin, motor only hums/buzzes, or stops under load
• Visible clues of failure can include a swollen, cracked, or leaking capacitor case

• Unplug the appliance before servicing; capacitors can retain a charge even when power is off
• Discharge the capacitor safely before handling
• Note wire positions; move leads to the same terminals and secure the capacitor in the original bracket/orientation
• Inspect connectors and replace any burnt or loose terminals to ensure a tight fit

Secures the capacitor in your laundry center. Replace if clip is broken, cracked, or capacitor becomes loose. Verify fit with your model number.

Plastic socket that holds the suspension rod ball in your washer. Replace if worn, cracked, or deformed to restore proper tub support and alignment.

Protective cover for the main wiring harness on laundry centers and washer-dryer combos. Replaces cracked, broken, or missing covers that expose wiring.

Fix non-responsive controls or dead unit issues with this main wiring harness. Restores electrical connections between control board and components.

This SCR 8-18 AB 1/2 is a replacement silicon controlled rectifier that restores proper power control to the appliance's control circuitry, helping the unit switch and regulate current reliably. What it does:

• Controls current flow in the appliance's power/control circuit for timed or regulated output
• Replaces a failed or intermittent SCR to stop erratic cycling, no-power, or control malfunctions
• Commonly used where electronic switching or phase control is required
• Helps restore stable operation when heating or motor circuits fail to receive proper control signals

• One SCR 8-18 AB 1/2 replacement component

• Disconnect power to the appliance before inspecting or replacing electrical components
• Observe ESD precautions and handle the SCR by its body; avoid touching leads
• Verify wiring and mounting orientation match the original part before final assembly