Parts for Electrolux EIED50LIW2: 02 - Cabinet / Drum Parts

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Mounting bracket for dryers and laundry centers. Secures components in place during operation. Replace if bent, cracked, or missing for proper fit.

Control panel cover for dryers. Replaces cracked, broken, or missing covers that expose internal components. Installs on the console housing assembly.

Rubber cushion bumper for dryers. Installs between panels or assemblies to reduce vibration and noise. Replace if cracked, worn, or missing.

Replacement air duct assembly with mesh screen for dryers. Installs between drum and heater. Replace if screen is burnt, cracked, melted, or missing.

Foam insulator strip that cushions dryer panels and reduces vibration. Replace if worn, compressed, or missing to maintain quiet operation and fit.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Fix dryer heating issues with this thermistor temperature sensor. Solves intermittent heat, cycle errors, and poor drying. Easy DIY repair.

Replace your dryer seal to prevent air leaks, heat loss, and moisture escape. Restores tight barrier for efficient drying. Check fit with your model.

Replace your dryer's drum assembly if it's cracked, dented, or worn. This rotating cylinder holds and tumbles clothes during the drying cycle.

This moisture sensor monitors dampness inside the dryer drum and signals the control when fabrics are dry, helping automatic cycles end on time and avoid overdrying. Replacing a failed sensor can restore consistent Auto Dry performance and cycle times. What it does:

• Detects moisture level via conductivity across the sensor surfaces inside the drum
• Sends feedback to the control so Auto Dry cycles advance and stop correctly
• Helps prevent overdrying and underdrying in sensor-based cycles
• Common symptoms of a faulty sensor may include: auto cycles ending too soon or running too long, clothes remaining damp, or the dryer staying on "Sensing" while timed cycles still work

• 1 moisture sensor

• Disconnect power and, if applicable, shut off gas before servicing
• Access the sensor at the front bulkhead/lint housing area; remove front panel as needed per model
• Transfer connectors and route wiring exactly as original; secure the sensor firmly
• Clean the sensor contact surfaces with rubbing alcohol; residue from dryer sheets or fabric softeners can affect readings

Replacement mounting bracket for dryers and laundry centers. Secures internal components in place. Order a new bracket if yours is cracked or broken.

Fixes dryers that won't start, stop mid-cycle, or have unresponsive buttons. This main control board restores all cycle functions and timing controls.

Replacement base for your dryer. Supports the cabinet and internal components. Needed when original is cracked, rusted, or structurally damaged.

Secures internal components in your dryer. Replace this mounting bracket if cracked, broken, or missing to restore proper alignment and stability.

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

Replaces cracked or broken air flow deflector baffle inside your dryer drum. Guides internal airflow for proper ventilation and cooling performance.

White molded baffle that lifts and tumbles laundry inside the dryer drum. Replace if cracked, broken, or missing to restore proper load movement.

Support bracket for dryer assembly. Mounts and secures internal components in place. Replace if cracked, bent, broken, or missing to restore proper fit.

Washer that fits between the support roller and shaft in your dryer. Replace if worn, cracked, or missing to maintain proper drum alignment and support.

Supports and guides the dryer drum as it rotates. Replace if the roller is cracked, worn, or causing noise. Sold individually, not pre-assembled.

Replacement nut that secures internal components in dryers. Restores clamping force when original nut is stripped, worn, or missing. Prevents loosening.

Adjustable leveling foot installs at the bottom of your appliance to ensure stability and proper leveling. Replace if broken, cracked, or missing.

A compressor protector that helps prevent electrical damage to the refrigerator compressor and supports reliable start-up. Replaces a failed protector to help restore normal compressor operation and reduce risk of repeated motor startups. What it does

• Prevents compressor damage by interrupting power during electrical faults or overloads.
• Supports proper compressor start-up so the fridge can maintain cooling.
• Common symptom fixes: compressor not starting, refrigerator not cooling, or repeated clicking/cycling at start.
• Works with the compressor relay/start components to ensure safe operation.

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Access usually requires removing the refrigerator back panel or service access panel to reach the compressor area.
• Handle electrical terminals carefully; confirm correct orientation and secure connections.

Dryer gasket seals the drum to prevent air leaks and maintain proper drying efficiency. Replace if torn, cracked, or causing noise. Verify fit with your model.

This door gasket is the refrigerator/freezer door seal that helps keep cold air inside for consistent temperatures and efficient operation. It replaces a worn or torn seal to reduce drafts and moisture buildup. What it does:

• Creates an airtight seal around the door edge to help maintain interior temperature
• Reduces frost, condensation, and energy loss from a leaking door
• Helps keep stored food fresher by preventing warm-air intrusion
• Addresses common symptoms like visible gaps, tears, or a door that won't stay cold

• One door gasket

• Inspect the door and frame for damage or debris before installing the new gasket
• Clean mounting surface and follow OEM alignment steps for a proper seal
• Warm the gasket slightly (per OEM guidance) if needed to ease installation and improve fit

Wire harness that connects control board, sensors, and electrical components in your dryer. Replace if wires are damaged, connectors are broken, or worn.

Secures components inside your dryer to prevent shifting during operation. Replace this retainer if it's damaged, missing, or broken to eliminate noise.

The High Temperature Adhesive is an OEM part for Frigidaire appliances. This adhesive is specifically formulated to withstand high temperatures and is used in various repair applications within appliances such as ovens, ranges, and dryers.The 1-ounce tube contains adhesive formulated to withstand the extreme heat inside dryer drums and cabinets

Causes of a bad adhesive can include exposure to extremely high temperatures over extended periods, contamination by dirt or grease, or the natural aging and drying out of the adhesive.

Symptoms of a bad high temperature adhesive include:

• Components or parts becoming loose or detached
• The adhesive becoming brittle or cracked
• Inability to properly bond surfaces exposed to high heat
• Visible deterioration or peeling of the adhesive

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.