Parts for Electrolux FFFH17F4QTA: 03 - Cabinet Parts

Water pooling in freezer? This drain screen traps debris before it clogs the drain tube. Quick snap-in replacement restores proper drainage flow.

This is a plastic breaker strip that fits along the upper area of the freezer compartment, serving as a trim piece that bridges the gap between the inner liner and the outer cabinet. It helps provide insulation and a finished appearance at the top of the freezer. Replace this strip if it is cracked, warped, or missing, which can allow cold air to escape and cause frost buildup.

This is a lower breaker strip (divider panel) that fits along the interior of the freezer compartment. It serves as a trim piece that covers the gap between the liner and the outer cabinet, helping to insulate and provide a finished appearance. Replace this part if it is cracked, warped, or missing, which can allow cold air to escape and cause frost buildup or temperature inconsistencies.

Replace missing, faded, or damaged labels on your refrigerator. This adhesive label restores cosmetic appearance and model identification on exterior surfaces.

Freezer not cooling or running warm? A failed evaporator fan motor stops cold air circulation. DIY-friendly repair typically takes 30-45 minutes.

The Door switch is an OEM replacement part for Frigidaire refrigerators. This part turns the light on/off as the door opens and closes.

Causes of a faulty door switch include normal wear of electrical contacts from repetitive on/off cycles. Moisture exposure may potentially corrode internal connections.

Symptoms of a bad light/switch include:

• The interior light fails to turn on when the door is opened
• The light stays on when the door is closed, leading to potential overheating
• An impact on the refrigerator’s temperature regulation due to the switch not signaling the door's closure

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

LED light bulb illuminates your refrigerator interior. Replace when bulb burns out, flickers, or stops working. Verify fit with your model number.

Interior light not working? This light socket provides the electrical connection for your freezer bulb. Simple DIY fix restores compartment lighting.

This temperature control knob replaces a worn or missing knob so you can easily adjust the cold-control setting. Restores smooth, precise temperature adjustments and a clean, factory look. What it does:

• Attaches to the cold-control (thermostat) shaft to change the temperature setting
• Provides secure grip and pointer alignment for accurate selections
• Typical failure symptoms: cracked or missing knob, stripped hub, or a knob that slips or won't turn the control

• 1 temperature control knob

• Disconnect power before servicing
• Pull the old knob straight off the shaft; avoid prying at an angle to prevent shaft damage
• Align the shaft shape with the new knob and press firmly until fully seated
• The pointer aligns with the control graphics after installation

Seals the evaporator cover to prevent air leaks, frost buildup, and temperature fluctuations. Replace if worn or cracked. Verify fit with your model.

Access panel cover that protects internal components and provides a finished look. Replace if the original is cracked, broken, or missing from your appliance.

Freezer won't shut off or runs continuously? A faulty temperature control thermostat is often the cause. Simple DIY fix in about 30 minutes with a screwdriver.

Secures the temperature sensing tube to the thermostat for accurate temperature control. Replace if loose, missing, or damaged to prevent erratic cooling.

This replacement tube routes water from the refrigerator's defrost area to the drain pan to help prevent leaks and pooling. A simple, direct-fit part for restoring proper drain flow and reducing water buildup. What it does

• Channels defrost and condensation water to the drain pan to prevent interior pooling.
• Helps maintain normal drainage to avoid ice buildup or water leaks.
• Restores a damaged, cracked or clogged original tube where flow is restricted.
• Works as a service part when inspecting drain path during defrost/drain issues.

• One replacement tube.

• Disconnect power to the appliance before starting any repair.
• Remove access panels as needed and route tube along the factory path; avoid sharp bends or kinks.
• Inspect drain openings and heater components while replacing the tube.

Creates the angled track for the hinge cam to glide smoothly. Replace when the door sticks, won't open fully, or doesn't self-close. Verify fit by model.

Small spacer that corrects fit and leveling between freezer components. Replaces worn, missing, or damaged shims to restore proper alignment and clearance.

Supports and pivots your freezer door for smooth opening and closing. Replace when worn or bent to restore proper alignment, improve sealing, and prevent air leaks or frost buildup. Confirm fit by model number.

Secures door stop to hinge bracket, controlling opening angle. Replace if pin is bent, broken, or missing to restore smooth door operation.

Carries defrost water from your freezer drain outlet to the drip pan. Replace if cracked, kinked, or detached to prevent leaks onto floors and cabinets.

This drain pipe connects the defrost drain outlet to the drain pan area, channeling condensation and defrost water away from the freezer compartment. It is a rigid or semi-rigid tube that slides into the drain opening and directs water downward. Replace this part if you notice water pooling inside the freezer, ice buildup near the bottom of the compartment, or water leaking onto the floor beneath the appliance.

Replacement light shield that covers and protects the interior bulb in your refrigerator. Install when the original lens is cracked, broken, or missing.

Replacement cabinet corner trim for freezers. Restores the finished edge where the original trim piece has cracked, broken, or gone missing. Easy install.

Supports and pivots the freezer door at the top hinge point. Replace this hinge if cracked, broken, or worn to restore proper door alignment and swing.

Specs: Hex head ,1/4-20 x 5/8

This tempered glass refrigerator shelf replaces a damaged or missing shelf to restore stable, easy-to-clean storage for food and containers. Designed for direct fit where this OEM shelf is specified. What it does

• Provides a flat, sturdy surface for storing food, containers and produce.
• Helps organize interior storage and prevents items from shifting or spilling.
• Smooth glass surface resists stains and wipes clean quickly.
• Replaces shelves that are cracked, chipped or missing.

• Remove food and any items from the area before installing.
• Handle shelf carefully—wear protective gloves to avoid cuts from broken glass.
• Sit the shelf into existing support rails or clips and ensure it is fully seated on both sides.
• Replace damaged support clips or rails before installing the new shelf.

Wire shelf for upright freezers. Installs by inserting side pegs into wall holes. Replace cracked, broken, or missing shelves or add extra storage.

This is a wire or metal trivet that sits inside the freezer compartment, functioning as a shelf or tray support to organize and separate frozen food items. It rests on the interior ledges or brackets of the freezer section. Replace this trivet if it is bent, rusted, or has broken welds that prevent it from sitting level and supporting items properly.

Basket handle for chest and upright freezers. Replaces broken, cracked, or missing handles that make it difficult to lift storage baskets in and out.

Wire basket for upright freezer storage organization. Replaces cracked, broken, or missing baskets. Slides onto rails for easy access to frozen items.

This is a mid-level wire or plastic storage basket that fits inside a chest or upright freezer to help organize frozen items. It slides or hangs inside the freezer compartment to keep food separated and accessible. Replace this basket if it is cracked, bent, has broken supports, or no longer sits securely in the freezer.

Secures hanging basket to freezer rack. Replaces broken, bent, or missing hanger to restore proper basket support and prevent sagging or detachment.

Fixes a loose or fallen wire basket inside your freezer. This support bracket secures hanging baskets in place for stable storage. Simple DIY repair.

Adjustable leveling foot installs at the bottom of your appliance to ensure stability and proper leveling. Replace if broken, cracked, or missing.

Replacement screw that secures freezer panels, brackets, and trim. Install when original hardware is missing, stripped, or loose to keep components aligned.

Replace your freezer's front kickplate grill panel. Covers the base opening beneath the door. Order a new one if yours is cracked, broken, or missing.

Hex head screw that secures panels, brackets, and internal components in refrigerators and appliances. Replace when missing, stripped, or damaged.

Plastic bearing that acts as a pivot point for freezer door opening and closing. Replace if cracked, broken, or worn from repeated use over time.

This breather valve regulates air pressure between the freezer compartment and the outside environment, allowing the door to open easily after the compressor cycles. It prevents a vacuum from forming inside the freezer as the air cools and contracts. Replace this valve if the freezer door is difficult to open shortly after closing or if you hear unusual hissing sounds from the freezer.

Adhesive-backed plastic clip secures wires and small hoses inside your freezer or refrigerator. Replace when loose or damaged to reduce rattling. Confirm fit with your model number before ordering.

Green plastic handle for freezer storage baskets. Replaces cracked, broken, or missing handles on sliding baskets. Direct fit replacement part.

Replacement screw that secures brackets, shelves, trim, panels, and covers inside your appliance. Install when the original is missing, stripped, or corroded.