Parts for Electrolux FFFH21F6QWA: 03 - Cabinet Parts

Water pooling in freezer? This drain screen traps debris before it clogs the drain tube. Quick snap-in replacement restores proper drainage flow.

Refrigerator making loud noises or not cooling? A worn evaporator fan blade often causes these issues. DIY-friendly repair typically takes 30 minutes.

This is a right-side breaker strip that serves as an insulating divider between the freezer and refrigerator compartments or between the inner liner and outer cabinet. It helps maintain proper temperature separation and prevents condensation from forming along the cabinet edges. Replace this strip if it is cracked, warped, or if you notice moisture or frost buildup along the right side of the compartment opening.

This is a plastic breaker strip that fits along the upper area of the freezer compartment, serving as a trim piece that bridges the gap between the inner liner and the outer cabinet. It helps provide insulation and a finished appearance at the top of the freezer. Replace this strip if it is cracked, warped, or missing, which can allow cold air to escape and cause frost buildup.

This is a lower breaker strip (divider panel) that fits along the interior of the freezer compartment. It serves as a trim piece that covers the gap between the liner and the outer cabinet, helping to insulate and provide a finished appearance. Replace this part if it is cracked, warped, or missing, which can allow cold air to escape and cause frost buildup or temperature inconsistencies.

Freezer not cooling or running warm? A failed evaporator fan motor stops cold air circulation. DIY-friendly repair typically takes 30-45 minutes.

The Door switch is an OEM replacement part for Frigidaire refrigerators. This part turns the light on/off as the door opens and closes.

Causes of a faulty door switch include normal wear of electrical contacts from repetitive on/off cycles. Moisture exposure may potentially corrode internal connections.

Symptoms of a bad light/switch include:

• The interior light fails to turn on when the door is opened
• The light stays on when the door is closed, leading to potential overheating
• An impact on the refrigerator’s temperature regulation due to the switch not signaling the door's closure

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

Light lens cover for refrigerator interior lighting. Replaces cracked, yellowed, or missing lens covers. Snaps into place over bulb compartment.

Powers your refrigerator's interior lighting. Replace when lights dim, flicker, or fail. Confirm fit with your model number before ordering.

Seals the evaporator cover to prevent air leaks, frost buildup, and temperature fluctuations. Replace if worn or cracked. Verify fit with your model.

Creates the angled track for the hinge cam to glide smoothly. Replace when the door sticks, won't open fully, or doesn't self-close. Verify fit by model.

Small spacer that corrects fit and leveling between freezer components. Replaces worn, missing, or damaged shims to restore proper alignment and clearance.

Supports and pivots your freezer door for smooth opening and closing. Replace when worn or bent to restore proper alignment, improve sealing, and prevent air leaks or frost buildup. Confirm fit by model number.

Secures door stop to hinge bracket, controlling opening angle. Replace if pin is bent, broken, or missing to restore smooth door operation.

Carries defrost water from your freezer drain outlet to the drip pan. Replace if cracked, kinked, or detached to prevent leaks onto floors and cabinets.

This drain pipe connects the defrost drain outlet to the drain pan area, channeling condensation and defrost water away from the freezer compartment. It is a rigid or semi-rigid tube that slides into the drain opening and directs water downward. Replace this part if you notice water pooling inside the freezer, ice buildup near the bottom of the compartment, or water leaking onto the floor beneath the appliance.

Cabinet corner trim piece for freezers. Covers and finishes the corner edge of the cabinet exterior. Replace if cracked, chipped, or missing.

Supports and pivots the freezer door at the top hinge point. Replace this hinge if cracked, broken, or worn to restore proper door alignment and swing.

Protective cover that snaps over your freezer's door hinge. Replace if cracked, broken, or missing to restore a finished look and shield the hinge.

Specs: Hex head ,1/4-20 x 5/8

Secures refrigerator door shelf and restores edge trim for stable storage. Replaces cracked, broken, or worn shelf frame to keep items supported.

Upper glass shelf assembly for freezer interior storage. Replace cracked, chipped, broken, or missing shelves to restore organized food storage space.

Replace a cracked, broken, or missing interior shelf in your freezer. Restores stable storage space for organized food placement inside the cabinet.

Secures internal components and panels in your freezer. Replace this support bracket if it's cracked, broken, or missing to restore proper alignment.

Freezer running constantly or not cooling? This main power control board restores temperature regulation and system control. Moderate difficulty, 1-2 hours.

Basket handle for chest and upright freezers. Replaces broken, cracked, or missing handles that make it difficult to lift storage baskets in and out.

This is a wire or plastic storage basket that slides into the freezer compartment to organize and separate frozen foods. It helps maximize storage space and allows easy access to items stored inside. Replace this basket if it is cracked, warped, has broken rails, or no longer slides smoothly on the tracks.

Secures hanging basket to freezer rack. Replaces broken, bent, or missing hanger to restore proper basket support and prevent sagging or detachment.

Fixes a loose or fallen wire basket inside your freezer. This support bracket secures hanging baskets in place for stable storage. Simple DIY repair.

Adjustable leveling foot installs at the bottom of your appliance to ensure stability and proper leveling. Replace if broken, cracked, or missing.

Replacement screw that secures freezer panels, brackets, and trim. Install when original hardware is missing, stripped, or loose to keep components aligned.

White toe grille panel for upright freezers. Mounts at base to cover components. Replace when cracked, discolored, or missing for a clean look.

Threaded insert nut creates secure anchor point in thin metal or plastic panels. Replace worn, stripped, or missing insert nuts to properly mount covers.

Replacement screw that secures brackets, shelves, trim, panels, and covers inside your appliance. Install when the original is missing, stripped, or corroded.

Hex head screw that secures panels, brackets, and internal components in refrigerators and appliances. Replace when missing, stripped, or damaged.

Plastic bearing that acts as a pivot point for freezer door opening and closing. Replace if cracked, broken, or worn from repeated use over time.

Replacement storage divider for upright freezers. Separates and organizes frozen items. Replace if cracked, broken, or missing to restore compartments.

This is a wire shelf designed to hang inside the freezer compartment, sometimes referred to as a pizza shelf due to its shape and placement. It provides additional flat storage space for frozen items. Replace it if the shelf is bent, rusted, or the mounting clips are broken, causing the shelf to sag or fall.

This is a small air baffle breather valve that helps equalize air pressure between the interior compartment and the outside environment. It allows air to pass through while helping maintain proper temperature regulation. Replace this valve if you notice excessive frost buildup, difficulty opening the door shortly after closing it, or unusual air pressure issues inside the unit.

Rubber grommet for freezer interior assembly. Replaces worn, cracked, or missing grommets that secure components or reduce vibration in your unit.

Replace your broken or missing freezer basket handle. This handle attaches to wire storage baskets, providing a grip for lifting and organizing items.

Adhesive-backed plastic clip secures wires and small hoses inside your freezer or refrigerator. Replace when loose or damaged to reduce rattling. Confirm fit with your model number before ordering.

Mounting screw for freezers and refrigerators. Secures internal components, panels, or shelving. Replace if stripped, missing, or damaged during repairs.