Parts for Electrolux FGVU21F8QFB: 03 - Cabinet Parts

Water pooling in freezer? This drain screen traps debris before it clogs the drain tube. Quick snap-in replacement restores proper drainage flow.

Fixes uneven cooling or warm top shelves in freezers. This blower wheel restores proper air circulation when the fan stops moving cold air effectively.

This is a right-side breaker strip that serves as an insulating divider between the freezer and refrigerator compartments or between the inner liner and outer cabinet. It helps maintain proper temperature separation and prevents condensation from forming along the cabinet edges. Replace this strip if it is cracked, warped, or if you notice moisture or frost buildup along the right side of the compartment opening.

This is a lower breaker strip (divider panel) that fits along the interior of the freezer compartment. It serves as a trim piece that covers the gap between the liner and the outer cabinet, helping to insulate and provide a finished appearance. Replace this part if it is cracked, warped, or missing, which can allow cold air to escape and cause frost buildup or temperature inconsistencies.

This is a plastic breaker strip that fits along the upper area of the freezer compartment, serving as a trim piece that bridges the gap between the inner liner and the outer cabinet. It helps provide insulation and a finished appearance at the top of the freezer. Replace this strip if it is cracked, warped, or missing, which can allow cold air to escape and cause frost buildup.

Freezer not cooling or running warm? A failed evaporator fan motor stops cold air circulation. DIY-friendly repair typically takes 30-45 minutes.

The Door switch is an OEM replacement part for Frigidaire refrigerators. This part turns the light on/off as the door opens and closes.

Causes of a faulty door switch include normal wear of electrical contacts from repetitive on/off cycles. Moisture exposure may potentially corrode internal connections.

Symptoms of a bad light/switch include:

• The interior light fails to turn on when the door is opened
• The light stays on when the door is closed, leading to potential overheating
• An impact on the refrigerator’s temperature regulation due to the switch not signaling the door's closure

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

Light lens cover for refrigerator interior lighting. Replaces cracked, yellowed, or missing lens covers. Snaps into place over bulb compartment.

Powers your refrigerator's interior lighting. Replace when lights dim, flicker, or fail. Confirm fit with your model number before ordering.

Seals the evaporator cover to prevent air leaks, frost buildup, and temperature fluctuations. Replace if worn or cracked. Verify fit with your model.

Creates the angled track for the hinge cam to glide smoothly. Replace when the door sticks, won't open fully, or doesn't self-close. Verify fit by model.

Supports and pivots your freezer door for smooth opening and closing. Replace when worn or bent to restore proper alignment, improve sealing, and prevent air leaks or frost buildup. Confirm fit by model number.

Secures door stop to hinge bracket, controlling opening angle. Replace if pin is bent, broken, or missing to restore smooth door operation.

Carries defrost water from your freezer drain outlet to the drip pan. Replace if cracked, kinked, or detached to prevent leaks onto floors and cabinets.

Drain pan for freezers, located beneath the unit to collect defrost water. Replace if cracked, warped, or leaking to prevent water damage to floors.

This drain pipe connects the defrost drain outlet to the drain pan area, channeling condensation and defrost water away from the freezer compartment. It is a rigid or semi-rigid tube that slides into the drain opening and directs water downward. Replace this part if you notice water pooling inside the freezer, ice buildup near the bottom of the compartment, or water leaking onto the floor beneath the appliance.

This small plastic clip secures the dishwasher drain hose to the pump assembly or discharge fitting, keeping the hose in place and helping prevent leaks or disconnection during operation. What it does:

• Holds the drain hose firmly to the pump or outlet fitting to maintain a watertight connection
• Prevents the hose from slipping free during drain cycles
• Helps stop water leaks and washing chamber flooding caused by a loose hose
• Useful when replacing a cracked or broken retaining clip

• One drain hose retaining clip

• Disconnect power and water supply before accessing the dishwasher lower access area
• Remove the access panel or kickplate to reach the drain hose and pump connection
• Use pliers or a flat tool to remove the old clip and snap the new clip over the hose/fitting until fully seated
• After installation, run a short drain cycle and inspect for leaks; re-secure if necessary

Replacement cabinet corner trim for freezers. Restores the finished edge where the original trim piece has cracked, broken, or gone missing. Easy install.

Supports and pivots the freezer door at the top hinge point. Replace this hinge if cracked, broken, or worn to restore proper door alignment and swing.

Specs: Hex head ,1/4-20 x 5/8

Upper glass shelf assembly for freezer interior storage. Replace cracked, chipped, broken, or missing shelves to restore organized food storage space.

The Glass Shelf is an OEM part for Frigidaire refrigerators. It provides a sturdy and clear surface for storing food items, helping to organize and maximize the refrigerator's storage space. The glass is designed to be durable and easy to clean, ensuring it can handle the daily demands of a busy kitchen.

Causes of a bad glass shelf can include impact damage from heavy or awkward items, thermal stress from temperature changes, or general wear and tear over time. Maintaining intact shelves is essential for safe and efficient food storage.

Symptoms of a bad glass shelf include:

• Visible cracks or chips in the glass
• Shattered or broken pieces
• Difficulty in supporting the usual weight of stored items
• Unstable or uneven surface

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Secures internal components and panels in your freezer. Replace this support bracket if it's cracked, broken, or missing to restore proper alignment.

Secures hanging basket to freezer rack. Replaces broken, bent, or missing hanger to restore proper basket support and prevent sagging or detachment.

Fixes a loose or fallen wire basket inside your freezer. This support bracket secures hanging baskets in place for stable storage. Simple DIY repair.

Adjustable leveling foot installs at the bottom of your appliance to ensure stability and proper leveling. Replace if broken, cracked, or missing.

Replacement screw that secures freezer panels, brackets, and trim. Install when original hardware is missing, stripped, or loose to keep components aligned.

Replacement screw that secures brackets, shelves, trim, panels, and covers inside your appliance. Install when the original is missing, stripped, or corroded.

Hex head screw that secures panels, brackets, and internal components in refrigerators and appliances. Replace when missing, stripped, or damaged.

Replacement mounting screw for freezer panels, trim, and brackets. Needed when original fastener is missing, stripped, or damaged during repairs.

Plastic bearing that acts as a pivot point for freezer door opening and closing. Replace if cracked, broken, or worn from repeated use over time.

This is a wire shelf designed to hang inside the freezer compartment, sometimes referred to as a pizza shelf due to its shape and placement. It provides additional flat storage space for frozen items. Replace it if the shelf is bent, rusted, or the mounting clips are broken, causing the shelf to sag or fall.

This breather valve regulates air pressure between the freezer compartment and the outside environment, allowing the door to open easily after the compressor cycles. It prevents a vacuum from forming inside the freezer as the air cools and contracts. Replace this valve if the freezer door is difficult to open shortly after closing or if you hear unusual hissing sounds from the freezer.

Replaces cracked or broken mounting bracket in your freezer. Securely holds internal components in proper alignment. Needed when original is damaged.

Mounting bracket that secures freezer shelves and internal panels. Replace if cracked, bent, or broken to restore proper alignment and stability.

Guide rail that supports and directs refrigerator drawers along their track. Replace when original is worn, cracked, or broken to restore smooth sliding.

Replacement drawer slide for freezers. Restores smooth gliding when original is broken, worn, or causes sticking. Essential for proper drawer alignment.

Supports and guides the crisper drawer for smooth sliding. Replace if cracked, broken from stress, or if drawer no longer sits securely in refrigerator.

Green plastic handle for freezer storage baskets. Replaces cracked, broken, or missing handles on sliding baskets. Direct fit replacement part.

Rubber grommet for freezer interior assembly. Replaces worn, cracked, or missing grommets that secure components or reduce vibration in your unit.

Basket handle for chest and upright freezers. Replaces broken, cracked, or missing handles that make it difficult to lift storage baskets in and out.

Replace your broken or missing freezer basket handle. This handle attaches to wire storage baskets, providing a grip for lifting and organizing items.

Adhesive-backed plastic clip secures wires and small hoses inside your freezer or refrigerator. Replace when loose or damaged to reduce rattling. Confirm fit with your model number before ordering.