Parts for Frigidaire FFTR18D2PS3: 05 - Cabinet Parts

Plastic cover that protects the evaporator fan and directs airflow in your refrigerator. Replace if cracked, broken, or missing to restore proper airflow.

Controls airflow between freezer and fresh food compartments. Attaches to the damper control shaft. Replace when cracked, stripped, or missing.

Refrigerator making loud noises or not cooling? A worn evaporator fan blade often causes these issues. DIY-friendly repair typically takes 30 minutes.

Secures moving components and provides a stable pivot surface in your refrigerator. Replace when worn, broken, or causing looseness and poor alignment.

Front evaporator fan motor mounting bracket

Replacement outer trim cover for refrigerators. Restores exterior appearance and protects internal components. Installs where original is cracked or missing.

Covers the factory test opening on your refrigerator cabinet or liner. Replace if missing, cracked, or damaged to restore a finished look and seal.

Size: 1" round

Plastic plug insert for refrigerator panels and structural openings. Replace if cracked, broken, or missing to maintain proper cabinet appearance.

Seals unused holes in refrigerator cabinet or liner. Prevents drafts, moisture, and pests from entering through open fittings. Restores clean appearance.

Refrigerator warm but freezer cold? A failed evaporator fan motor stops air circulation. This motor replacement restores cooling in 30-60 minutes.

Secures moving components and provides a stable pivot surface in your refrigerator. Replace when worn, broken, or causing looseness and poor alignment.

Replacement mounting screw for refrigerator panels, handles, brackets, and internal fixtures. Order when original screws are stripped, lost, or damaged.

Black button plug that covers upper hinge mounting holes on your refrigerator. Replace if original plug is missing, cracked, or broken for a clean finish.

Lower hinge bracket secures the refrigerator door at the bottom, allowing smooth pivoting. Replace if bent, cracked, or causing door misalignment and sagging.

Protective washer that sits between the door hinge and frame. Replaces worn or missing washers that cause door sagging, dragging, or poor seal contact.

Fits between the refrigerator door and hinge pin to set door height and reduce friction. Replace if worn, missing, or damaged for smooth door movement.

Black center hinge bracket mounts between refrigerator doors to support and align them. Replace if bent, cracked, or worn to restore proper door swing.

Supports and pivots the refrigerator door at the center hinge bracket. Replace if worn, damaged, or missing to restore smooth door swing and alignment.

Replacement corner trim that covers the cabinet edge of your refrigerator. Restores a finished look to cracked, chipped, or missing corner pieces.

Secures the top of your refrigerator door to the cabinet. Replace if cracked, broken, bent, or lost during a move to restore proper door alignment.

Black upper hinge cover conceals and protects your refrigerator's door hinge assembly. Replace if cracked, broken, or missing to restore appearance.

Replacement shelf support grommet for refrigerators and freezers. Provides stability for shelves. Replace if broken, missing, or worn to restore proper shelf support.

Specs: Hex head ,1/4-20 x 5/8

Fixed rollers with leveling screw for the left hand side. For right side, order part 241889001.

Replacement lower hinge pin for refrigerator doors. Acts as a pivot point to hang and support the door. Replace if worn, broken, or missing from a move.

Replace missing or stripped #10-32 x 3/4" screws that secure panels, brackets, and trim on refrigerators. Restores tight fit and eliminates rattles.

Kickplate grille that covers the bottom front of your refrigerator. Replace if cracked, broken, or missing clips cause it to fall off repeatedly.

Factory fastener that secures panels, brackets, and internal components. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattling.

Supports the compressor on the refrigerator's rear base. Replace if cracked, broken, or worn to keep compressor properly seated and reduce vibration damage.

Metal rivet fastener permanently secures panels, brackets, and internal components in refrigerators. Replace damaged, missing, or worn rivets to restore fit.

Protective cardboard or plastic cover that installs over the internal cooling system and wiring. Replace if cracked, torn, ripped, or missing.

Replacement mounting screw for securing brackets, trims, covers, and components inside your refrigerator. Replace missing, stripped, or lost hardware.

Mounting screw for refrigerators and freezers. Secures panels, brackets, and internal components. Replace when stripped, missing, or damaged.

Replacement front roller assembly for refrigerators. Includes leveling screw. Needed when roller is cracked, broken, or leveling screw is bent or damaged.

Hex head screw that secures panels, brackets, and internal components in refrigerators and appliances. Replace when missing, stripped, or damaged.

Touch-up paint for appliances to cover scratches, chips, and worn areas on exterior surfaces. Restores appearance of refrigerators, ranges, and more.

Restores tight seals to stop leaks, drafts, and temperature loss. Replace when you notice gaps, noise, or moisture issues. Verify fit with your model.

Color: White

Nylon washer for the evaporator fan motor shaft in refrigerators. Replace if worn, cracked, or missing to ensure proper fan alignment and operation.