Parts for Frigidaire MRTG23V9RF0: Cabinet Parts

The Evaporator Fan Cover is an OEM part for Frigidaire refrigerators. The fan cover houses and protects the evaporator fan, which spins consistently to circulate cold air throughout the refrigerator compartment.

Causes of a bad evaporator fan cover include cracks or breaks that compromise the fan's protection. Over many years of operation, the plastic material can become brittle or warped.

Symptoms of an issue with the evaporator fan cover include:

• Inconsistent or insufficient air circulation inside the refrigerator
• Cooling performance decreases, causing temperature fluctuations
• Higher electricity usage as the fan must work harder without optimal airflow
• Unusual noises from the rear grill area

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models. 

Controls airflow between freezer and fresh food compartments. Attaches to the damper control shaft. Replace when cracked, stripped, or missing.

Refrigerator making loud noises or not cooling? A worn evaporator fan blade often causes these issues. DIY-friendly repair typically takes 30 minutes.

This fan motor mounting bushing is used in refrigerator fan motor assemblies to prevent vibrations between the fan motor and the surrounding components. Over time, the rubber on the bushing may become cracked or broken and fall off. Loud noises coming from the refrigerator's freezer section where it is mounted are a good indicator that the bushing needs to be replaced. To start, disconnect the refrigerator's power and empty the refrigerator and freezer's contents into an ice chest to keep them cold until the motor mount bushing is replaced. Open the freezer door and remove the plastic access panel on the back wall; the fan blade and motor are located behind it. Gently pull the fan blade off the center post. Remove the screws holding the motor in place and remove the motor. Take the old bushing off and install the new bushing. Replace the panel. Put the food contents back inside the freezer and refrigerator and restore the power.This motor mounting bushing is an authentic OEM replacement part sourced directly from the manufacturer. It is sold individually. It is designed for use in refrigerators manufactured by Frigidaire, Kenmore, Gibson, and Kelvinator.

Front evaporator fan motor mounting bracket

Replaces a cracked, broken, or missing evaporator coil cover in top-mount refrigerators. Protects coil assembly and maintains proper airflow.

Covers the factory test opening on your refrigerator cabinet or liner. Replace if missing, cracked, or damaged to restore a finished look and seal.

Size: 1" round

Plastic plug insert for refrigerator panels and structural openings. Replace if cracked, broken, or missing to maintain proper cabinet appearance.

The refrigerator ice maker hole plug is a rubber or plastic cap that seals the pre-drilled opening in the refrigerator cabinet wall that is used for ice maker water line connections. It keeps cold air from escaping through the unused hole in refrigerators that do not have an ice maker installed. Replace or install this plug if cold air is leaking through an open hole in the back wall of the refrigerator, causing temperature fluctuations or frost buildup.

This motor circulates cold air throughout the refrigerator compartment and is located behind the rear panel inside the fridge. Replace it if you notice unusual noises, inadequate cooling, or frost buildup in the refrigerator section.

Secures moving components and provides a stable pivot surface in your refrigerator. Replace when worn, broken, or causing looseness and poor alignment.

Replacement mounting screw for refrigerator panels, handles, brackets, and internal fixtures. Order when original screws are stripped, lost, or damaged.

Button plug insert for freezers and refrigerators. Covers screw holes or mounting points on interior walls and shelving. Replace if cracked or missing.

This roller assembly consists of small caster-style wheels mounted on a support ring, designed to allow a shelf, drawer, or internal component to slide smoothly inside the refrigerator or freezer compartment. It supports the weight of stored items while enabling easy access. Replace this assembly if the rollers are cracked, seized, or if the shelf or drawer no longer glides properly and feels stuck or wobbly.

Secures the bottom hinge assembly on your refrigerator door. Replace this bracket if it's bent, broken, or cracked to restore proper door alignment.

Protective washer that sits between the door hinge and frame. Replaces worn or missing washers that cause door sagging, dragging, or poor seal contact.

Sits on the center hinge pin to maintain proper door spacing and smooth pivoting. Replace if worn, cracked, or missing to restore even door alignment.

Supports and pivots the refrigerator door at the center hinge bracket. Replace if worn, damaged, or missing to restore smooth door swing and alignment.

Secures the top of your refrigerator door to the cabinet. Replace if cracked, broken, bent, or lost during a move to restore proper door alignment.

Replacement shelf support grommet for refrigerators and freezers. Provides stability for shelves. Replace if broken, missing, or worn to restore proper shelf support.

Specs: Hex head ,1/4-20 x 5/8

This roller assembly consists of small caster-style wheels mounted on a support ring, designed to allow a shelf, drawer, or internal component to slide smoothly inside the refrigerator or freezer compartment. It supports the weight of stored items while enabling easy access. Replace this assembly if the rollers are cracked, seized, or if the shelf or drawer no longer glides properly and feels stuck or wobbly.

Replacement lower hinge pin for refrigerator doors. Acts as a pivot point to hang and support the door. Replace if worn, broken, or missing from a move.

Front kickplate grill for refrigerators. Covers the bottom panel beneath the door. Replace if cracked, discolored, or missing for a clean finish.

Factory fastener that secures panels, brackets, and internal components. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattling.

Supports the compressor on the refrigerator's rear base. Replace if cracked, broken, or worn to keep compressor properly seated and reduce vibration damage.

Metal rivet fastener permanently secures panels, brackets, and internal components in refrigerators. Replace damaged, missing, or worn rivets to restore fit.

Replacement mounting screw for securing brackets, trims, covers, and components inside your refrigerator. Replace missing, stripped, or lost hardware.

Fix a refrigerator light that won't turn on or off when the door opens or closes. This door-activated light switch is a simple 5-minute DIY repair.

Seals the evaporator coil cover to prevent air bypass and direct cold air over coils. Replace if worn or damaged to restore airflow and reduce frost.

Nylon washer for the evaporator fan motor shaft in refrigerators. Replace if worn, cracked, or missing to ensure proper fan alignment and operation.

Replacement mounting screw for refrigerator panels, handles, brackets, and internal fixtures. Order when original screws are stripped, lost, or damaged.