Parts for Frigidaire MRTG23V9RF0: System Parts

Refrigerator not cooling properly? This condenser coil assembly releases heat from the refrigerant to restore efficient cooling and keep food cold.

Includes service line.

Fixes frost buildup in freezer or refrigerator compartment. This defrost heater melts ice from evaporator coils during defrost cycles. Moderate DIY repair.

Freezer not freezing or fridge too warm? The evaporator coil absorbs heat to cool your refrigerator. Professional installation recommended for this repair.

Aluminum strap secures the defrost heater against the evaporator coil. Replace if broken, cracked, or missing to maintain proper heater contact.

Channels defrost water from the evaporator to the drain pan. Replace if cracked, broken, or leaking to prevent water pooling in the fresh-food compartment.

Protective shield that covers internal refrigerator components. Installs inside the cabinet to prevent debris buildup and contact damage. Replace if cracked or broken.

This is a left-hand insulator block that mounts near the evaporator inside the refrigerator or freezer compartment. It supports and insulates the evaporator assembly, reducing heat transfer and keeping the cooling system running efficiently. Replace this block if it is damaged, deteriorated, or missing, which can cause frost accumulation, inconsistent temperatures, or unusual noises from the evaporator section.

This is a right-hand insulator block that mounts near the evaporator inside the refrigerator or freezer compartment. It helps secure and insulate the evaporator assembly, preventing unwanted heat transfer and vibration. Replace this block if it is cracked, broken, or missing, which can lead to uneven cooling, frost buildup, or rattling noises from the evaporator area.

Freezer frost buildup? Defrost thermostat regulates defrost cycles to prevent ice accumulation. DIY repair takes 15-30 minutes with basic tools.

Refrigerator compressor base supports and secures the compressor unit. If your refrigerator is noisy or vibrating, this mounting base may need replacement.

Rubber grommet that mounts and cushions the compressor to reduce vibration transfer. Replace if cracked, worn, or missing to restore quiet operation.

Secures the compressor to the mounting bracket in your refrigerator. Replace if washer is missing, cracked, or worn to restore proper support.

Secures the compressor to the chassis, reducing movement and noise. Replace if your compressor shifts or rattles during operation. Confirm fit with model.

Collects water from evaporator defrost cycles. Mounts near compressor under refrigerator. Replace if cracked, leaking, or damaged to prevent odors.

If your freezer isn't cooling or runs constantly, a failed compressor is likely the cause. This compressor kit restores refrigerant circulation and cooling.

Fix a refrigerator that won't cool or run with this compressor start relay. Common fix for clicking sounds and warm temps. Simple 15-minute repair.

Black rubber mounting grommet that secures tubes and wires in your refrigerator. Replace if cracked, worn, or missing to properly hold components in place.

Mounting screw for refrigerators and freezers. Secures panels, brackets, and internal components. Replace when stripped, missing, or damaged.

Factory fastener that secures panels, brackets, and internal components. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattling.

Fix a refrigerator that won't start or runs but doesn't cool with this run capacitor. Common repair for compressor issues. Moderate DIY difficulty.

Secures and organizes wiring harnesses in your refrigerator. Replace if broken, cracked, or wires are loose. Confirm fit with your model number.

This #8-32 x 3/8 screw secures appliance panels, brackets, and assemblies. Replace a missing or stripped fastener to keep parts tight and aligned, reduce vibration, and restore proper fit in compatible refrigerators and freezers.

• Machine-thread fastener sized #8-32, 3/8-inch length
• Secures control housings, trims, covers, and support brackets per model design
• Replaces missing, worn, or corroded screws that cause loose or rattling parts
• Helps maintain alignment and stability after service

• Unplug the appliance; shut off water if applicable
• Match thread size to the original and start by hand to avoid cross-threading
• Use the correct driver; do not overtighten, especially into plastic
• Verify component alignment and operation after fastening

• Thread size: #8-32
• Length: 3/8 inch

Refrigerator not cooling properly? A broken condenser fan blade prevents heat removal from coils. Easy DIY fix—just pull off and press on. Video included.

Supports the compressor on the refrigerator's rear base. Replace if cracked, broken, or worn to keep compressor properly seated and reduce vibration damage.

Metal rivet fastener permanently secures panels, brackets, and internal components in refrigerators. Replace damaged, missing, or worn rivets to restore fit.

Tube connector for refrigerators. Connects tubing in water or refrigerant lines. Replace if cracked, leaking, or broken to restore proper connection.

Secures the evaporator or condenser fan shroud to the refrigerator cabinet. Replace this mounting screw if stripped, missing, or broken during repair.

Foam seal tape creates airtight barriers around refrigerator components. Replace when worn, compressed, or damaged to restore proper sealing and efficiency.

Replacement mounting screw for refrigerator panels, handles, brackets, and internal fixtures. Order when original screws are stripped, lost, or damaged.