Parts for Gibson GTF1040CS0: 05 - Cabinet / Top Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Connects your washing machine to the household water supply. Replace this flexible inlet hose if cracked, leaking, or worn to restore proper flow.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Connects your washing machine to the household water supply. Replace this flexible inlet hose if cracked, leaking, or worn to restore proper flow.

An electronic component that regulates the washing machine motor's speed during different wash cycles. Replace if your washer doesn't agitate properly, makes unusual noises, or fails to complete spin cycles.

This replacement screw secures appliance panels and components. With a #10-16 thread and 0.75-inch length, it replaces stripped, rusted, or missing hardware to restore a tight, rattle-free fit and reduce vibration and noise.

• Fastens cabinet panels, brackets, or internal parts in washers and dryers
• Direct replacement for worn or lost screws to keep assemblies aligned and secure
• Helps address loose/vibrating panels, rattling noises, or visible gaps/misalignment
• Spec: #10-16 thread; 0.75-inch length

• Disconnect power; for washers, also shut off water supply
• Match the original screw location; start threads by hand to prevent cross-threading
• Use a driver that fits the screw head properly; tighten snugly without overtightening

Washer won't spin or drain? Error code E47? The door lock assembly often causes these issues. This moderately easy repair typically takes 30 minutes.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

Outer door panel that replaces a damaged or worn outer door surface, restoring the appliance's finished exterior and protecting inner door components. Ideal when the exterior is dented, scratched, or cosmetically damaged. What it does

• Provides the finished exterior surface for the appliance door and protects internal door components from damage.
• Restores appearance after dents, scratches, rust spots, or cracked paint.
• Re-establishes mounting surfaces and edge trim where tabs or attachment points are intact.
• Helps prevent further corrosion or moisture intrusion into the door assembly.

• Disconnect power (and water, if applicable) and follow before starting; use proper PPE.
• Door removal and panel replacement often require basic hand tools; save and reuse original screws, handles, and trim unless replacements are supplied.
• Transfer any hardware, insulation, or inner-door pieces from the old door to the new panel as required.
• Large panels can be awkward—have a second person assist to avoid dropping or bending the panel.

Replaces cracked, warped, or broken inner door panel on front-load washers. Restores door structure and provides mounting surfaces for bins and seals.

Machine screw secures panels, brackets, and internal components in washers. Replace missing, rusted, or stripped screws to restore proper fit and alignment.

Washer door strike ensures proper door closure and sealing during wash cycles. Replace if door won't latch or seal. Verify fit with your model number.

Replacement washer door hinge that secures and aligns the door for smooth opening and closing. Needed when original hinge is cracked, broken, or worn.

This is a 10-16 x .312 sheet-metal screw with a quad-style panel head used to secure appliance panels and trim. It replaces missing or damaged screws to help stabilize panels and reduce rattling. What it does:

• Fastens control panels, trim pieces, and thin sheet-metal components
• Restores secure fit where screws are missing or stripped
• Helps stop panel vibration, rattling, or misalignment caused by loose fasteners
• Small, common mounting screw for interior and exterior appliance panels

• One 10-16 x .312 quad panel head screw (quantity: 1)

• Disconnect power to the appliance before working on panels or controls
• Use the correct screwdriver head to avoid stripping the quad head
• Tighten by hand; do not overtighten to prevent stripping or cracking panels
• Keep extra screws on hand; replace any that are corroded or damaged

This small pin helps align and position the washer's front or top panel during assembly and operation. It ensures proper alignment between panels and maintains structural integrity. Replace this part if panels are misaligned, the washer vibrates excessively, or there are gaps between panels.

Replacement screw for securing panels, components, and assemblies in appliances. Needed when original screws are stripped, lost, or damaged during repair.

Secures the top or front panel to your laundry center frame. Replace if bracket is cracked, broken, or missing to restore proper panel alignment.

Spring retainer for washers and laundry centers. Secures internal springs in place. Replace if cracked, broken, or missing to restore proper assembly.

This is a replacement pan-head, locking screw used to secure the top bracket on compatible Frigidaire appliances. It provides a reliable fastener that helps keep the top bracket and panels held firmly in place. What it does:

• Secures the top bracket to the cabinet or chassis to prevent bracket movement or rattling
• Restores proper alignment of top panels and trim that may be loose or sagging
• Uses a locking feature to resist loosening from vibration
• Pan head design provides a low-profile, finished appearance once installed

• One screw as shown

• Use the matching #8-32 driver or bit and tighten until snug; avoid over-torquing to prevent stripping
• Turn off power and remove panels as needed before accessing the bracket area
• Replace only with the same size and thread type to ensure secure fit
• Replace all related screws for even support

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Metal sheet-metal screw secures panels, brackets, and internal components. Replace when missing, stripped, or damaged to restore proper fit.

Front control panel for washers that houses console buttons and display. Replaces cracked, damaged, or worn panels to restore appearance and access.

This replacement overflow shield directs excess water away from sensitive components to help prevent leaks and water damage in the appliance. It restores proper drainage protection when the original shield is cracked, warped, or missing. What it does:

• Channels overflow or stray water away from critical areas to reduce risk of leaks
• Replaces damaged, cracked, or missing overflow shielding
• Helps maintain proper drainage pathways and component protection
• Commonly used when you see water pooling or dripping near the shielded area

• One overflow shield

• Inspect surrounding seals and fasteners; replace any that are damaged before installing the new shield
• Installation typically requires basic hand tools; secure the shield in the original mounting points
• Disconnect power to the appliance before starting work and restore power only after reassembly

The Cord is an OEM replacement part for Frigidaire washing machines. Extending from the rear of the unit, it safely powers the washer through a connection to a wall outlet.

Causes of cord failure are normal wear from frequent coiling and plugging/unplugging motions over the appliance's lifespan. Rodents or sharp edges may also damage the outer jacketing.

Signs of a bad cord include:

• Exposed or severed copper wiring visible inside
• External cracks, splits or abrasions eroding the casing  
• Erratic behavior during the wash cycle
• GFCI/EGCI outlet tripping frequently

Compatible models also include Electrolux, KitchenAid, Jenn-Air, and Kenmore options. Maintaining safety is a top priority.

This bushing protects the appliance service cord where it passes through the cabinet, reducing wear and preventing chafing that can expose wiring. It's a simple replacement that restores a safe cord entry point. What it does:

• Cushions and centers the service cord at the cabinet opening to prevent abrasion
• Helps keep the cord from rubbing on sharp metal edges that can cause insulation damage
• Reduces risk of shorting, sparking, or intermittent power caused by a worn cord
• Commonly replaced when the existing bushing is cracked, missing, or deformed

• One service cord bushing

• Disconnect power (unplug or switch off breaker) before servicing
• Inspect the cord and surrounding insulation; replace the cord if damage is found
• Push the bushing into the cabinet opening, then route the cord through the bushing until seated
• Reuse only if undamaged; do not force a damaged bushing into place

Washer won't fill with water or only fills with hot? The water inlet valve controls water flow into the tub. DIY repair takes about 30 minutes.

This is a threaded leveling leg assembly that screws into the base of a washing machine. It allows you to adjust the height at each corner to keep the appliance stable and level on the floor. Replace this part if the leg is stripped, broken, or if your washer vibrates excessively or walks across the floor during the spin cycle.

Metal sheet-metal screw secures panels, brackets, and internal components. Replace when missing, stripped, or damaged to restore proper fit.

Secures and seals your washer's drain hose connection to prevent leaks. Replace if cracked, brittle, or leaking. Confirm fit with your model number.

Replacement drain hose directs used water from your washer to the household drain. Needed when original hose is cracked, split, or leaking.

An electronic component that regulates the washing machine motor's speed during different wash cycles. Replace if your washer doesn't agitate properly, makes unusual noises, or fails to complete spin cycles.

Replacement control panel for laundry center units. Installs on the front console to house controls and displays. Order if your panel is cracked or damaged.

Base assembly for laundry center units. Structural foundation that supports the appliance cabinet. Replace if cracked, damaged, or compromised.

Shipping bolt kit secures the washer drum during transport. Replace missing or lost bolts when moving your washer to prevent damage to the suspension system.

Shipping bolt kit secures the washer drum during transport. Replace missing or lost bolts when moving your washer to prevent damage to the suspension system.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.