Parts for Poulan PP4818A: Chassis / Bar / Handle Parts

This part is a replacement screw. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. This part can be used to replace a defective or misplaced screw in a variety of lawn equipment. This screw is a high-quality piece of standard hardware with multiple different uses. Screws are essential for securing parts of the equipment, but can easily become lost, stripped, or otherwise damaged. If screws are missing, it can affect the functionality of the equipment. A Phillips head or flat head screwdriver can be used to install this screw. It's important when working on or near any engine to make sure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this screw, the appropriate owner's manual and equipment diagrams should be referred to. As an authentic replacement part, this screw is suitable for use on several models of lawn equipment manufactured by Husqvarna, Poulan, and other brands. This is a genuine part made of high-quality, durable metal and is sold individually.

This rear handle cover is a genuine Husqvarna part, sold individually. This rear handle cover can be used as a replacement part in a chainsaw.The rear handle cover might have to be replaced if it is damaged to the point that the cover falls off or if the rear handle cover is damaged itself. This could occur if the rear handle cover wears away over time or comes into close contact with a hard object that warps or dents the component beyond functionality. If this occurs, the rear handle cover should be removed and replaced by this genuine OEM replacement part.This is a genuine OEM replacement directly from the manufacturer. It is sold individually. This rear handle cover is compatible with the following outdoor appliance brands: Husqvarna and Craftsman.

This is a rear handle that can be used on a variety of chainsaws made by major manufacturers. If the handle is broken, lost, or no longer works as expected, it should be replaced. There will be no way to hold onto the chainsaw without it.Visually inspect the rear handle for any damage to determine whether the part needs to be replaced. Check for excessive scratches, cracks, or broken areas that make the chainsaw difficult or impossible to use. Use work gloves while making the replacement and make sure to disconnect the spark plug wire before working. The part will require only basic tools to replace and ensure a working chainsaw. Remove the broken handle and replace it with a quality replacement component. Make sure to reattach the spark plug wire before using the tool again.This rear handle is an authentic OEM replacement part that is sourced directly from the manufacturer. It is sold as an individual part. The handle is made for use with Craftsman and Poulan chainsaws.

This replacement part is a screw and is intended for use in a variety of lawn equipment. This is a genuine replacement part made by Husqvarna. Screws are an important part of many different types of machinery as they hold other parts in place and secure. A new screw might be needed if the current ones are loose or missing. It is common that screws might become stripped overtime and will need to be replaced. Be sure to double check the size of the screw as many places on lawn equipment will require different size screws. Be sure the appliance is completely powered down and cooled off before attempting to repair an appliance. For more detailed instructions on how to install this specific part, see the owner's manual. This is an OEM part sourced directly from the manufacturer. It is sold individually. This replacement part is compatible with different types of lawn equipment made by Husqvarna.

This part is a replacement clip socket wrench. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. The intended use for this part is to properly replace a defective, lost, or broken clip socket wrench in chainsaws.This clip socket wrench helps to secure components of the chainsaw together properly while also being easily removable when necessary. This part can easily become lost, corroded, or otherwise defective over time and thus may require replacement. Always ensure that the equipment is completely powered off and is cooled down before attempting to start the repair process. For more accurate information on the installation of this particular clip socket wrench, reference the owner's manual or equipment diagrams for specific instructions and part location. This is an authentic OEM part and as such is sold individually and made from durable and high-quality metal. This clip socket wrench can be used with a variety of chainsaw models manufactured by Husqvarna, Poulan, and other brands.

This is an adjusting wrench tool that is designed to be used for the maintenance of 50cc chainsaws. This tool includes two wrench sockets with screwdriver functionality. The main way an adjusting wrench tool is used is to adjust the bar tension. This ensures the chainsaw chain is tight and the tool is ready for use. It can also be used to quickly remove spark plugs on the tool.The adjusting wrench tool is an identical replacement to be used with the original is faulty or missing. It doesn't stay on the chainsaw but acts as a tool to ensure the chainsaw is in good working order. It's made of strong metal and can be lost or damaged through regular use. If the current adjusting wrench tool is lost or damaged, this replacement part will do the same things as the original. It fits many different chainsaws by various manufacturers.The adjusting wrench tool is sold as a single device and sourced directly from the manufacturer. It is an authentic OEM replacement tool that can be used with Poulan, Craftsman, and Husqvarna chainsaws.

This is a thrust washer that can work as a replacement for several models of chainsaws. Thrust washers are flat washers that will help to provide a tight fit between the connected pieces. The washer can help to reduce the amount of vibration, and it will keep the different parts from touching one another, which could cause wear. Check the washers when servicing the chainsaw to see if they might need to be replaced.The washers are durable and can last for a long time. However, there is the risk they could become lost when working on the machine, or that they could corrode or wear down. Replacing the washer is easy and should not take long to do.This thrust washer can be used to replace washers in certain models of chainsaws from Craftsman, Husqvarna, and Poulan. The washer is sold individually, so owners might want to buy several to have them available. This is a genuine OEM replacement part that has been sourced from the manufacturer.

The clutch drum assembly is an important part of the chainsaw. When the clutch has been engaged, the assembly will turn and move the chain around the bar. Without this assembly, the chain would not move, and the chainsaw would not be usable. It is important for chainsaw owners to check the performance of their clutch and clutch assembly regularly to look for signs of wear and tear or issues with the performance. Often, the clutches will continue to work past the point when they should be replaced. It is safe and wiser to replace the clutch assembly as soon as any issues are noticed. Replacement of the clutch assembly will require a set of wrenches. Start by removing the chain brake, the bar, and the chain. Remove the cover and the sparkplug. Bind the piston to remove the clutch without having it spin. Remove the clutch and add the new assembly. Seat the clutch, unbind the piston, and then secure the bar, chain, and the chain brake. Tension the chain and then test out the new clutch. This is a genuine OEM part sourced from the manufacturer. It will work with many models of chainsaws from Husqvarna, Poulan, and Craftsman.

Here is an authentic clutch friction washer that is sourced from the manufacturer. It is for use with several types of handheld outdoor power equipment. Other names for the part include clutch friction disk and clutch washer. The washer works as a friction disk that will help create the proper fit between components in the machine, which helps to engage the clutch. It is made from durable metal. The clutch friction washer that comes with the machine tends to be durable, but it may still need to be replaced at some point. The washer could become corroded, or it could break. It could also become lost when the owner is performing other maintenance on the machine. A wrench and screwdriver will typically be needed to conduct the replacement. Owners should check their manuals to ensure the correct location for installing the washer. The genuine OEM clutch friction washer is sold individually. It can work with more than 150 models of chainsaws, hedge trimmers, and string trimmers. Brands that have models compatible with the part include Craftsman, Husqvarna, Weed Eater, Poulan, and Poulan Pro.

A clutch on a chainsaw is what enables the engine to turn a low RPM without the chain moving. It is a crucial component for operating the device safely. Without it, the blade or chain spins continually and leaves operators at risk for harm or injury. The clutch on any chainsaw works automatically and does not have a control or trigger to activate it. If your chainsaw is not automatically idling without halting the chain spinning, it could be time for a new clutch assembly. It requires only a screwdriver to do the repair This is a full replacement clutch assembly for chainsaws made by Husqvarna, Poulan, Craftsman, and several other brands. This OEM part is complete and features the clutch shoes and spring. It is an individual component and is not shipped with other hardware..

This specific OEM handguard is black in color and made of plastic. It provides operators a comfortable handle grip to hold onto securely and safely while operating and carrying the outdoor power equipment machine. A new handguard will be needed if the part is broken, cracked, or damaged in any way. It's important to replace this part immediately, because any damage to the handguard makes the operator vulnerable to injury, especially when operating a chainsaw. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment machines.This is a genuine Husqvarna part sourced directly from the manufacturer and sold individually. This handguard is compatible with chainsaws and saws manufactured by Husqvarna and Poulan.

This part is a handguard spring for a chainsaw. The handguard spring returns the handguard to the forward position when the handguard is released.A new handguard spring may be needed if the handguard no longer returns to the forward position when the handguard is released. If the spring is broken in any way, it will no longer work properly and will need to be replaced. The spring could become damaged or break after normal use due to normal wear and tear over time. If this is the case, it will need to be replaced. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment.This handguard spring is a genuine Husqvarna part. It is sold individually. This particular handguard spring is compatible with chainsaws that are manufactured by the Husqvarna brand and the Craftsman brand.

A clutch cover assembly is bolted to the engine and has the clutch disc between it and the pressure plate. The springs within the clutch cover will force the pressure plate against the disc, moving it against the flywheel to send power into the manual transmission. This is a clutch cover assembly for Husqvarna and Craftsman chainsaws, including gear with the Poulan named attached. This is the cover for the assembly and ships as an individual part. It does not contain any of the other components associated with the transfer of power to the transmission.

This nut is used to attach a mounting bar to a chainsaw or pole saw. The nut attaches in slightly different ways depending on the product, but it will feed a bolt that attaches the base of the bar to the pole or housing of the saw. If the nut becomes stripped or corroded due to exposure to the elements, it will need to be replaced. A socket wrench and a socket set are needed to install the part. simply screw it into the chain bar studs, making this a quick and easy replacement. The flat side of the nut should face outward to create a flush effect with the rest of the handle. The other side will fit into the bar. This part sold independently. It works with both Poulan and Husqvarna products and is a genuine OEM product sourced directly from the manufacturers.

This adjustable pin bar is used on chainsaws and other lawn and garden equipment to ensure a blade is adjusted to the appropriate rate of tension. When the chainsaw blade is properly adjusted, it will cut faster and better. The pin bar is made out of a durable metal but can become damaged over time. If the pin bar is not working correctly or has broken, it will need to be replaced.If a chainsaw or pole pruner is no longer performing as well as it used to, the adjustable pin bar may need to be replaced. To replace this pin, the cover of the chainsaw will need to be removed. Take the gear that has the screw and pin bar on it out of the machine. Next, remove the broken adjustable pin bar and replace it with a new part. Reassemble the tool for it to be ready to use.This adjustable pin bar is designed for use on Craftsman, Poulan, Poulan Pro, and Husqvarna chainsaws, pole pruners, and string trimmers. It is a genuine OEM replacement component that is directly sourced from the manufacturer. The part is sold individually.

This bar adjustment retainer is an integral part of the bar adjustment mechanism that assists with securing the screw in many kinds of lawn and garden equipment. The retainer is made of durable metal and is used to replace a faulty, broken, or damaged original part. Sometimes the bar adjustment retainer will break or become damaged and need to be replaced.If the retainer breaks, it can cause the bar adjustment screw to become damaged or stripped. Inspecting for damage requires taking apart the equipment. Use work gloves to remove the chain bar cover and get access to the retainer. Replace it with a new retainer and screw. The bar adjustment pin should be placed at the end of the screw. Thread the screw through until it catches on the retainer. Once that's complete, the other parts can be reassembled.This bar adjustment retainer is a genuine OEM replacement part that is directly sourced from the manufacturer. It is sold as an individual part. The retainer is made to be used with string trimmers, edgers, hedge trimmers, pole pruners, and chainsaws created by Craftsman, Husqvarna, Poulan, and Poulan Pro. This part is sold individually.

This bar adjustment kit is a replacement bar adjustment for a chainsaw. This kit contains the adjustment bolt, retainer ring, and a pin. It sits on the inside of the clutch cover and is positioned to put tension on the chain. Keeping the right amount of tension in the chain is crucial for users’ safety. If the chain becomes too loose, it can kick back or come off during operation. Through normal repeated use, the chain will become looser on the guide bar over time. Replacing the bar adjustment kit will restore the tension in your chainsaw to the appropriate amount. Be careful not to overtighten the chain, though, as it can cause unwanted friction and become a fire hazard. This is a genuine OEM part comes straight from the manufacturer and can be easily installed on Crossman or Poulan products with nothing more than a screwdriver. Simply remove the clutch cover, remove the old bar adjustment kit, replace it with the new one, and then align the corresponding parts when reattaching the cover. This part ships individually.

This part is a replacement screw. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. This part can be used to replace a defective or misplaced screw in a variety of lawn equipment. This screw is a high-quality piece of standard hardware with multiple different uses. Screws are essential for securing parts of the equipment, but can easily become lost, stripped, or otherwise damaged. If screws are missing, it can affect the functionality of the equipment. A Phillips head or flat head screwdriver can be used to install this screw. It's important when working on or near any engine to make sure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this screw, the appropriate owner's manual and equipment diagrams should be referred to. As an authentic replacement part, this screw is suitable for use on several models of lawn equipment manufactured by Husqvarna, Poulan, and other brands. This is a genuine part made of high-quality, durable metal and is sold individually.

This replacement part is a cylinder spring assembly and is intended for use in different types of lawn equipment. This is a genuine replacement part made by Husqvarna. This spring is used in chainsaws and it is intended to help the engine run to its full capacity. A new cylinder spring assembly might be needed if the current one is damaged or missing. If there are unusual noises coming from the inside of the appliance, it might be due to the spring assembly. It is recommended that the user wear work gloves while replacing this part. This cylinder spring assembly is sold individually and is a genuine OEM replacement part sourced directly from the manufacturer for long lasting use. Refer to the owner's manual for more specific instructions.

This screw is designed to be used in many different chainsaws to connect and hold together various components. The screw can be used on its own or placed with a nut in a pre-drilled and threaded hole. If a nut is going to be used, it is best to choose one with the same threading and finish as the screw that will be used. A screw can become damaged in many ways that will require a replacement. Corrosion, excessive stress, or high temperatures may weaken the screw. In some cases, the damage can cause it to break or become loose and no longer properly secure other components of the chainsaw. A visual inspection can help determine if corrosion is present or the screw is damaged or broken. If the screw is stripped, a bolt remover may be needed to remove it to make the replacement.This screw is a genuine OEM replacement part provided directly from the manufacturer. It is sold as an individual component. The screw is compatible with chainsaws created by Poulan, Poulan Pro, Craftsman, and Husqvarna. A screwdriver is needed to replace, remove, or install the replacement part.

This is a replacement for the front handle of a chainsaw. A quality chainsaw handle is essential for those who are using these machines. They provide a place for the user to grip and to ensure they have a good hold of the chainsaw when it is in use. If the handle has an issue or has broken, it will need to be replaced before the owner uses the chainsaw again. It is not safe to operate the chainsaw if there is a problem with the handle.The handles are made from durable material, but there is still a potential for them to wear down or break over time or due to accidents. Replacing the chainsaw handle is relatively easy and should not take more than 15 to 20 minutes. Owners will want to be sure the chainsaw is cool and may want to remove the chain before getting started.The chainsaw front handle replacement will work for certain models of chainsaws from Husqvarna, Craftsman, and Poulan. The handle is sold individually. It is a genuine OEM replacement part sourced from the manufacturer.

This replacement part is a flywheel. This is a genuine replacement part made by Husqvarna. This part is found in most machinery and works closely with the engine. This part is able to convert certain types of energy and inertia so that the engine can run properly. A new flywheel might be needed if the current one is visibly missing or damaged in any way. It is possible that over time the flywheel might not work as effectively as in previous uses. If this is the case it is recommended that it be replaced. Be sure the engine is completely turned off before replacing this part to prevent injury and maintain safety. This flywheel is sold individually and is sourced directly from the manufacturer. This part is a genuine OEM replacement part to ensure proper fit and long-lasting use.

This is a starter hub replacement designed for use in select models of lawn and garden equipment. The starter hub is part of the starter system. The starter pulley will engage the hub, which will then engage the flywheel to start the motor. The hub is subject to constant repetitive motion and rotation, so it can often become worn or damaged over time. Without a functional starter hub, the engine will not be able to operate safely, which is why an OEM replacement is essential.It is important to wear gloves when performing engine repairs. In order to replace the starter hub, the old part will need to be removed from the starter assembly. Then, the new hub can be put in place and connected to the flywheel and the starter pulley. Be sure to disconnect the power supply before performing any engine repairs.This genuine OEM starter hub that is manufactured by Poulan. It is designed for use with select models of chainsaws. The hub is sold as an individual replacement part. There is no hardware included and other parts will require an additional purchase.

This genuine OEM hub spring is designed to fit select models of chainsaws. The hub spring is responsible for providing the spring action that reacts to the pull starter. This generates the power that rotates the flywheel and helps engage the engine in the starting process. The spring becomes worn and extended with regular use. Since it is metal, it may also be subject to corrosion or other environmental damages. In either case, the hub spring should always be replaced promptly if it is found to be defective or damaged in any way. This genuine hub spring can be used for a variety of chainsaws from Poulan, Husqvarna, AYP, Sears/Craftsman, Roper, Poulan Pro, and Weed Eater. This item is sold as an individual unit. Springs are under pressure and can be dangerous to replace so always use caution. Allow the engine to cool before beginning repairs and always wear gloves for any kind of engine part repairs or replacements.

This part is a screw. This is a genuine Husqvarna replacement screw and has been sourced directly from the manufacturer. This replacement part is intended to replace missing or broken screws in a number of different small outdoor power equipment models.With regular usage, screws can easily become stripped, rusted, or lost. This can lead to improper functionality of outdoor power equipment. It's important to use genuine manufacturer replacement screws to ensure the highest-quality materials and a proper fit that will keep equipment in good working order. When installing screws, always follow proper guidelines and abide by appropriate safety measures. Husqvarna screws are manufactured from high-quality, durable material. This replacement part is a high-quality piece of standard hardware with many different applications. For proper installation and usage guidance, it is recommended to refer to the equipment manufacturer diagram.This replacement screw is designed to fit various models of Husqvarna, Craftsman, Poulan, and Weed Eater trimmers and hedge trimmers, blowers, and chainsaws. Please note this screw is a genuine OEM part and is sold individually.

When you pull the starter rope, it will engage the chainsaw starter pulley, which then makes the flywheel engage and causes the engine to fire up. The assembly consists of a few small working parts that can wear out or become damaged or lost over time. The included spring may wear or you may lose one of the screws that secure it in place. This OEM kit makes it easy to replace the entire assembly with an exact fit for compatible models. When installing this starter pulley kit, remove or disconnect the spark plug for your safety. This genuine OEM chainsaw starter pulley kit is designed for use with a variety of chainsaws that are manufactured by brands like Husqvarna, Craftsman, and Poulan. Check your user manual to confirm part number compatibility for an exact fit. This starter pulley kit is sold individually and comes with everything that you need for a quick and easy replacement.

The starter spring is what is used to create the recoil to start the engine on pull-start chainsaws, blowers, trimmers, and other lawn equipment. When the starter handle is pulled, the rope extends and pulls on the spring, causing it to tighten and then release, which creates the action to fire the motor. It may also be called the recoil spring, rewind spring, or return spring, but they all refer to the starter spring. Over time, this can become worn with use, and in some situations, it can even break completely. If the starter rope will not rewind into the housing, the spring may be twisted and need to be replaced. If so, this genuine OEM starter spring will do the job for compatible machines. This model is manufactured by Husqvarna and compatible with various Poulan and Husqvarna lawn equipment. This spring may serve as a replacement for many machines including blowers, hedge trimmers, grass trimmers, chain saws, and saws. Check the user manual for compatibility and fit, as well as part numbers. Be sure to install this according to all instructions and diagrams for safe and proper operation.

This baffle is a genuine Husqvarna part. Baffles are used to control or restrict the flow of fluids, gases, and other materials, so it is an important part. The size of the holes on the baffle and the baffle itself can be controlled, modified, or manipulated in different ways to affect the power of the chain saw. Because it is connected to the muffler, doing so may affect the noise level of the chain saw.It is a genuine OEM part sourced from the manufacturer. This Husqvarna baffle is black, spherical in shape, and looks like a large screw. This part contains all necessary sections of the baffle. It can be used to replace the baffle on a functioning chain saw with which it is compatible.This Baffle is compatible with Poulan chainsaws, specifically the PP4818A chain saw and PP5020AV chainsaw. It may also fit other chain saws that are compatible with Husqvarna parts, such as Weed Eater, Craftsman, RedMax, and AYP.

This genuine Husqvarna rope kit can be used as a replacement part for chainsaws. The function of a rope kit for a chainsaw is to work in conjunction with the starter handle to power up the engine. The rope is coiled around a pulley held in place by spring tension and the rope is pulled in order to start up the engine of the chainsaw. This mechanism is generally called a recoil start. A rope kit might have to be ordered as a complete replacement for the starter rope of a chainsaw as well as the small components that attach the rope to the pulley, the spring, and the starter handle. If there is damage to the rope through long-term usage or corrosion to the material that impedes the rope from starting up the engine through the recoil starter mechanism, the rope should be removed and replaced with this genuine OEM part kit before using the chainsaw again. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer. It is sold individually. This rope kit is compatible with the following brands: Husqvarna, Craftsman, and Poulan.

This screw is designed to be used in many different chainsaws to connect and hold together various components. The screw can be used on its own or placed with a nut in a pre-drilled and threaded hole. If a nut is going to be used, it is best to choose one with the same threading and finish as the screw that will be used. A screw can become damaged in many ways that will require a replacement. Corrosion, excessive stress, or high temperatures may weaken the screw. In some cases, the damage can cause it to break or become loose and no longer properly secure other components of the chainsaw. A visual inspection can help determine if corrosion is present or the screw is damaged or broken. If the screw is stripped, a bolt remover may be needed to remove it to make the replacement.This screw is a genuine OEM replacement part provided directly from the manufacturer. It is sold as an individual component. The screw is compatible with chainsaws created by Poulan, Poulan Pro, Craftsman, and Husqvarna. A screwdriver is needed to replace, remove, or install the replacement part.

This is a replacement chainsaw fan housing that can work with several models of chainsaws. The fan housing attaches to the handle starter and protects the fan, while still allowing for airflow. If the housing is damaged, owners will want to replace it. Not having a cover for the fan could be dangerous, and it could increase the risk of further damage to the chainsaw.This yellow fan housing is made from durable plastic. If the plastic cracks or elements of the housing have started to break off, it should be replaced. The replacement procedure is relatively easy for the housing. Owners will want to be sure the chainsaw is cool and may want to remove the chain for safety before making the replacement.The chainsaw fan housing will work with a range of models from Husqvarna and Poulan. The high-quality part is a genuine OEM replacement sourced from the manufacturer. It is sold individually.