Parts for Kitchenaid YKFEG500EBS8: Chassis Parts

This side panel is a replacement cabinet trim piece that restores the exterior finish and protects the refrigerator side from dings and scratches. It matches original fit and appearance for a clean, factory look. What it does

• Covers and protects the refrigerator cabinet side from damage and wear
• Restores a uniform exterior appearance after dent or cosmetic repair
• Helps maintain proper panel alignment and mounting for adjacent parts
• Matches OEM shape so doors and trim fit correctly

• One side panel

• Intended for cabinet-side replacement; verify side (left/right) using your model diagram before ordering
• Remove power and empty nearby shelves before starting; handle panel edges carefully to avoid cuts
• May require basic tools (screwdriver, trim removal tool) and a second person for proper alignment

This is a replacement mounting screw used to secure appliance panels and components. It restores proper fastening so panels and parts stay aligned and stable during normal use. What it does:

• Fastens appliance panels, trim or internal components in place
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop panel vibration and maintain proper component alignment
• Matches OEM fit where specified for a secure installation

• One replacement mounting screw

• Verify screw size and fit before installation; use the correct screw location from your parts diagram
• Turn off and disconnect power to the appliance before accessing internal components
• Hand-start the screw to avoid cross-threading; tighten until snug—do not over-tighten
• Wear safety glasses and follow manufacturer service instructions when applicable

The Power Cord is an OEM part for Whirlpool ranges. It transmits electrical power from the home's outlet to the range, allowing it to function properly. As the power conduit, the cord is essential for powering burners, oven functions, and electronic controls. 

Symptoms of a bad power cord include:

• Range not receiving power or not powering on
• Loose, frayed, or damaged appearance of the cord
• Tripped circuit breakers related to the range circuit
• Shock or electrical hazards near the range outlet

Causes of a bad power cord can be normal wear and tear over time, accidental cuts or punctures, bending fatigue from improper storage, or damage from heat if placed too close to the range top.

This OEM replacement cord from Whirlpool ensures safe, reliable power to your range. It is compatible with select models from Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, and Admiral.

A Torx screw replacement used to secure appliance panels and components for stable operation. Designed as a direct-fit fastener to replace stripped or missing screws so panels and assemblies stay properly attached. What it does:

• Replaces damaged, stripped, or missing Torx-head screws that hold appliance parts together
• Restores secure fastening for control panels, trim pieces, brackets, and access covers
• Helps eliminate rattles, loose panels, or gaps caused by missing hardware

• One Torx screw

• Disconnect power and follow appliance safety procedures before servicing
• Use the correct Torx driver bit size to avoid cam-out or head damage
• Tighten until snug; avoid overtightening which can strip threads or damage parts
• Swap all like screws to ensure uniform fit and torque

The Thermal Fuse is an OEM replacement part for Whirlpool ovens. This safety device is designed to prevent the oven from overheating by cutting off electrical power if the internal temperature exceeds a safe level.

The thermal fuse can fail due to normal wear and tear, prolonged exposure to high temperatures, or electrical surges. Accumulation of grease and debris around the fuse can also cause it to malfunction.

Symptoms of a bad thermal fuse include:

• The oven not heating up
• The oven shutting off during use
• No power to the oven
• Error codes related to temperature control

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

This terminal block is the insulated connection point where the appliance's incoming power ties into the internal wiring. Replacing a heat-damaged or loose block restores a safe, reliable electrical path and helps prevent arcing and intermittent power loss.

• Connects the supply conductors to the unit's internal wiring
• Provides insulated posts to securely fasten and distribute power
• Helps maintain tight, low-resistance connections
• Common failure signs: melted/discolored plastic, burned or loose terminals, arcing, scorching, or intermittent/no power after confirming the cord and breaker

• Disconnect power at the breaker or unplug the appliance; verify no voltage before servicing
• Photograph or label wire positions to ensure correct reassembly
• Inspect and replace any heat-damaged wire ends or lugs; use appropriate terminals
• Tighten connections securely and ensure wires are fully seated and strain-relieved as originally installed

This replacement light bulb restores interior illumination inside your appliance. Swap it in for a burned-out bulb so you can clearly see contents and monitor operation when the door opens or the light button is pressed.

• Provides interior light inside the appliance cavity
• Direct replacement for a failed or broken bulb
• Common symptoms: no light when the door opens, flickering/intermittent light, visibly darkened or broken bulb

• Disconnect power to the appliance before servicing
• Allow the old bulb and nearby surfaces to cool completely
• Remove any lens or cover to access the socket; install the new bulb in the same orientation as the original
• Handle with clean, dry hands or gloves; do not overtighten. Restore power and test

This replacement terminal block cover encloses the appliance's incoming power connections. It protects the wire terminals from accidental contact and debris, restoring a safe, finished connection area when the original cover is damaged or missing. What it does:

• Covers and shields the power terminal block where the supply wires connect
• Helps prevent accidental contact with live electrical connections
• Helps keep dust and debris out of the connection area
• Common signs: missing or broken cover, cover won't stay attached, visible heat damage or discoloration on the original cover

• One terminal block cover

• Disconnect power at the breaker or unplug the appliance before servicing
• Access the terminal block per your model's service information
• Reuse existing mounting hardware; position and secure the new cover without pinching wires
• Inspect wires/terminals for heat damage or looseness and correct before reassembly

The Bake Element is an OEM replacement part for Whirlpool ovens. It is a component responsible for generating the heat necessary for baking and roasting operations within the oven cavity.

Symptoms of needing to replace the bake element include:

• Uneven or inconsistent baking results
• Difficulty in reaching or maintaining the desired oven temperature
• Visible damage or burnout on the element itself
• Unusual smells or odors associated with a faulty heating element

Causes of a faulty bake element can include normal wear and tear over time, electrical malfunctions, or physical damage due to impact or excessive temperature fluctuations.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore oven models.

This hidden oven floor pan sits under the bake element to protect the oven cavity from spills and debris while helping maintain proper heat distribution. It replaces a damaged or corroded oven floor shield for safer, cleaner operation. What it does:

• Collects spills and drips below the hidden bake element to protect the oven floor from damage.
• Supports the hidden bake element assembly and helps direct heat within the oven.
• Replace if the pan is warped, rusted, has holes, or causes persistent smoke or burning odors during use.
• Prevents food and debris buildup that can create smoke or affect cooking performance.

• Disconnect power to the appliance and allow the oven to cool completely before starting.
• Remove oven racks and follow OEM access steps; panels or the element may need to be loosened to remove the pan.
• Handle the pan carefully — edges can be sharp and the part may be dirty or hot.

The Screw is an OEM part for Whirlpool ranges. This screw is used to secure various components within the range, ensuring that parts such as panels, control boards, or burners are firmly attached and remain stable during operation.  

Causes of a bad range screw can include regular wear and tear, over-tightening, or exposure to high heat.  

Symptoms of a bad range screw include:

• Loose or unstable components within the range
• Difficulty in securing parts during maintenance or repair
• Visible damage or wear on the screw
• Parts becoming misaligned or rattling during operation

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This leveling foot adjusts the appliance's height at the front to keep the cabinet stable and level. A properly leveled unit helps reduce vibration and noise and ensures doors, drums, and drawers operate smoothly.

• Supports the appliance and provides front height adjustment
• Helps correct rocking, vibration, and excessive noise from an unlevel appliance
• Can improve door alignment and smooth operation when the cabinet is leveled
• Common wear or damage can cause wobbling or difficulty staying level

• Unplug the appliance and, if applicable, turn off the water supply before servicing
• Tip or lift the unit carefully; use a helper to avoid injury
• Thread the new foot into the base and adjust until the cabinet is level and stable
• Tighten any applicable lock nut and recheck level after repositioning the appliance

The Leveling Leg is an OEM part for Whirlpool ranges. It's designed to ensure your range is perfectly balanced and stable on uneven floors. By adjusting the height of the leveling legs, you can prevent wobbling and ensure that your cooking surface is perfectly horizontal, which is critical for even cooking and baking.

Causes of a malfunctioning Leveling Leg can stem from physical impact damage, corrosion in humid conditions affecting integrity and adjustability, and wear over time, particularly if frequently adjusted or cleaned aggressively.

Symptoms of a bad Leveling Leg include:

• The range tilts or wobbles, making cooking uneven.
• Difficulty sliding pots and pans across the cooking surface due to the appliance not being level.
• Increased strain on other components of the range, which could lead to premature wear or failure.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This heat shield protects nearby components from excessive heat by deflecting and insulating oven/range surfaces. It helps maintain safe cabinet temperatures and prevents heat-related damage to adjacent parts. What it does:

• Deflects and shields nearby components from direct heat
• Prevents heat damage to wiring, insulation, and cabinet panels
• Stops rattling or contact when the original shield is warped or missing
• Safe symptom link: replace if you see scorched insulation, warped metal, or unusual heat transfer to nearby surfaces

• Disconnect power (and gas, if applicable) and allow appliance to cool fully before starting
• Use basic hand tools; refer to your service manual for exact removal and attachment points
• Inspect surrounding components and replace any heat-damaged parts during reassembly

This spacer provides a precise gap for proper alignment and clearance between components, helping maintain correct part positioning for reliable operation. It's a simple replacement that restores intended spacing and reduces wear. What it does:

• Positions and separates adjoining parts to maintain correct clearance
• Helps prevent rubbing, misalignment, or binding of moving components
• Restores factory spacing after maintenance or part replacement
• Fits where the original spacer was used to support assembly alignment

• One spacer as shown

• Inspect surrounding components and mounting surfaces for damage before installing
• Remove power to the appliance and follow manufacturer service instructions
• Install in the same orientation as the original spacer and verify proper clearance
• If fasteners or adjacent parts are worn, replace them to ensure a secure fit

The broil element is an OEM replacement part for Whirlpool ranges. It provides intense heat from above to brown and crisp foods like breads, meats, and vegetables.

Causes of a bad broiler element include scaling or charring developing on the coils over many cooking cycles. Wiring damage from cleaning chemicals is also possible.

Symptoms of a failed element include:

• Incomplete or uneven browning of broiled foods
• Reduced or inconsistent heat output
• The element making popping/crackling noises when in use
• Safety issues like exposed coils or wires posing burn risks

This OEM replacement is compatible with KitchenAid, Jenn-Air, and other brands.

The Temperature Sensor is an OEM part for Whirlpool ovens and ranges. It monitors the internal temperature of the oven cavity and communicates with the oven control board to maintain accurate cooking temperatures. This ensures that your oven heats to the correct temperature for baking, roasting, and broiling.

Causes of a bad temperature sensor can include normal wear and tear, exposure to high temperatures over extended periods, or damage from accidental impacts or electrical surges.

Symptoms of a bad temperature sensor include:

• Incorrect oven temperatures
• Overcooking or undercooking of food
• Oven not heating up
• Error codes displayed on the oven control panel

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This hinge receiver mounts to the appliance frame and accepts the door hinge arm/pin. It keeps the door aligned and secure so it opens and closes smoothly. Replacing a worn or cracked receiver restores proper door action.

• Anchors the hinge arm/pin at the cabinet/frame for smooth door movement
• Maintains door alignment and consistent closing action
• Wear or damage can cause a loose or sagging door, misalignment, or binding
• Common signs include clicking/grinding noises and visible cracks or deformation

• Disconnect power; allow the appliance to cool and shut off gas/water if applicable
• Support or remove the door to access the receiver
• Remove mounting fasteners, swap in the new receiver, and align per service instructions
• Reinstall the door and verify smooth movement and full closure

The Bottom Oven Panel is an OEM part for Whirlpool ranges. This panel is located at the bottom of the oven cavity, protecting the internal components and providing a smooth surface for easy cleaning.

Causes of a bad Bottom Oven Panel can include exposure to excessive heat or spills, causing warping, discoloration, or damage to the panel.

Symptoms of a bad Bottom Oven Panel include:

• Visible cracks, dents, or other physical damage
• Discoloration or surface deterioration
• Loose or dislodged panel, exposing internal components

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This rail base provides the structural support for the refrigerator drawer/rail assembly, restoring smooth drawer alignment and preventing sagging or binding. It's a direct-fit replacement that helps maintain proper drawer operation and cabinet fit. What it does:

• Supports and aligns the drawer/rail assembly so drawers slide smoothly
• Secures the lower rail to the cabinet to prevent shifting or sagging
• Restores proper drawer clearance and prevents sticking or uneven movement
• Addresses symptoms like crooked or loose drawers, binding, or gaps at the drawer edge

• One rail base

• Disconnect power to the appliance before beginning work
• Remove drawer(s) and any trim panels to access the rail area
• Use basic hand tools; avoid overtightening fasteners to prevent damage

This rail base provides the structural support for the refrigerator drawer/rail assembly, restoring smooth drawer alignment and preventing sagging or binding. It's a direct-fit replacement that helps maintain proper drawer operation and cabinet fit. What it does:

• Supports and aligns the drawer/rail assembly so drawers slide smoothly
• Secures the lower rail to the cabinet to prevent shifting or sagging
• Restores proper drawer clearance and prevents sticking or uneven movement
• Addresses symptoms like crooked or loose drawers, binding, or gaps at the drawer edge

• One rail base

• Disconnect power to the appliance before beginning work
• Remove drawer(s) and any trim panels to access the rail area
• Use basic hand tools; avoid overtightening fasteners to prevent damage

This factory screw secures panels, brackets, or trim within your appliance. Replacing a missing or stripped fastener restores a tight fit, reduces vibration and rattles, and helps keep components aligned for reliable, long-term performance.

• Fastens panels, brackets, or trim to the appliance cabinet/frame
• Replaces damaged, rusted, or missing hardware
• Helps eliminate vibration noises, gaps, and loose-fitting parts
• Supports proper alignment of adjoining components

• Disconnect power; turn off gas/water supplies where applicable.
• Match to the original screw from your model's parts diagram before installation.
• Start threads by hand to avoid cross-threading; use the correct driver bit for the head.
• Tighten snugly—do not overtighten to prevent stripping threads or cracking plastic bosses.

This oven rack replaces a bent, missing, or rusty shelf so bakeware sits level and slides smoothly. Restore full support and the correct cooking height inside your oven for safer loading and consistent results.

• Provides sturdy, adjustable support for pans, sheets, and dishes at multiple rack positions
• Slides on the side rails for easy loading and removal
• Helps maintain proper clearance for airflow and even heating
• Common replacement signs: warped wires, flaking or rusted finish, wobble/tipping, poor sliding, or a missing rack

• Allow the oven to cool completely; disconnect power or shut off gas before service
• Pull the old rack forward to the stop, lift the front to clear the stop ends, and remove
• Insert the new rack with the stops toward the back; level it on the rails and slide fully in
• The rack is seated securely before use

This anchor tip is a small snap-in retainer that secures spring or linkage components and helps keep moving parts aligned. It restores proper anchoring to reduce looseness, rubbing, and rattling for smoother operation. What it does:

• Secures a spring, clip or small linkage to its mounting point so parts stay in place
• Keeps moving components aligned to prevent binding or rubbing
• Helps eliminate rattles or noise caused by a dislodged retainer
• Provides a simple replacement for a damaged or worn plastic anchor

• Disconnect power to the appliance before starting any repair.
• Verify correct orientation and mounting location before snapping the anchor tip into place.
• Use needle-nose pliers for placement if needed; press gently until fully seated. Do not force or deform the part.
• If other components show wear or damage, inspect and replace as required for a complete repair.

Size: 10-32

This replacement screw restores secure fastening for appliance panels and components, helping stop loose parts and rattling so controls and panels stay aligned. Use when original screws are missing, stripped, or damaged. What it does:

• Secures panels, trim, control boards, brackets, or components to the appliance frame
• Stops rattling, vibration noise, and loose or misaligned parts caused by missing or damaged fasteners
• Replaces stripped, corroded, or missing screws to restore proper fit and function
• Matches OEM fit and threading for straightforward hardware replacement when the correct screw is identified

• Turn off power and unplug the appliance before accessing internal components
• Use the correct screwdriver or bit to avoid stripping the head; do not force mismatched drivers
• Tighten until snug—do not overtighten, which can strip threads or crack plastic
• Keep removed hardware organized and verify the replacement screw matches the original before installation

This main back insulation panel replaces the factory foam insulation behind the refrigerator cabinet to help reduce heat transfer and minimize noise. Installing the correct back insulation helps the refrigerator maintain temperature more consistently. What it does:

• Provides thermal barrier behind the cabinet to slow heat gain from the rear.
• Helps limit compressor and airflow noise by absorbing sound near the rear cavity.
• Commonly replaced when insulation is damaged, missing, compressed, or when the appliance has higher-than-normal run times or inconsistent cooling.
• Protects internal components from external temperature swings and debris entering rear cavities.

• Disconnect power before accessing the rear of the appliance and remove any rear access panels or brackets to reach the insulation location.
• Handle the panel gently to avoid tearing or compressing the insulation; secure using original clips/adhesive or replacement fasteners as applicable.
• Ensure the insulation fits flush and does not interfere with wiring, tubing, or moving parts.

This insulation wrap surrounds a designated hot component inside the appliance to contain heat and shield nearby wiring and surfaces. Replacing a worn or missing wrap helps maintain proper temperatures and safe, reliable operation.

• Provides a thermal barrier around the specified component or area
• Helps protect adjacent wiring and panels from excessive heat
• Replace if the original is charred, brittle, torn, contaminated, or missing
• Common signs include hot spots, scorch marks, or a burning odor near the component

• Disconnect power before servicing and allow the appliance to cool completely
• Note the original routing/overlap and install the new wrap in the same orientation
• Wear gloves and eye protection; edges and fibers can irritate skin
• Ensure the wrap doesn't obstruct airflow or moving parts and is secured as originally

The Insulation is an OEM part for Whirlpool ranges. It is designed to insulate the oven cavity, helping to maintain the desired temperature during cooking and improving energy efficiency.  

Causes of a bad range insulation can include wear and tear over time, exposure to high temperatures leading to deterioration, or physical damage from handling or installation.  

Symptoms of a bad range insulation include:

• Increased cooking times
• Uneven cooking or baking results
• Excessive heat on the exterior of the range
• Higher energy consumption

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.