Columbia Parts

Governor arm shaft for small engines on lawn and garden equipment. Connects governor assembly to carburetor. Replace if worn, damaged, or broken.

The shave plate is a common snowblower part that attaches to the back of the blower housing and directs snow into the auger and blade assembly so it can be cleared. The particular layer of ice and snow this blade is removing is the hardest and heaviest part of the snowfall. The shave plate is also called the scraper bar or scraper blade. Periodically, because it is in direct contact with the concrete surface below the snow, the shave plate wears out and must be replaced. A shave plate may be worn, gouged, or sliced so it does not smoothly remove the snow from the sidewalk. Replacing the shave plate is a simple task that can be accomplished in 30 minutes or less. The shave plate is connected to the blower housing by four adjustable fasteners that are removed. This genuine OEM replacement part is manufactured by Genuine MTD. It is compatible with a great variety of snowblowers, including Husky, Troy-Bilt, Yard Machines, MTD, Cub Cadet, and Yard-Man. This OEM part is sold individually.

This lower chute is a quality replacement part that is used on several models of snowblowers. It is made of high-quality plastic for durability and is placed so it can direct snow in a certain direction when it leaves a snowblower. Over time and with regular use, this part can become damaged. If this occurs, it will need to be replaced so the discharged snow ends up in the right location.When replacing the lower chute, a wrench and work gloves will be needed. The snowblower should be placed on a flat surface, and the spark plug wire needs to be disconnected. The gearbox and the lower chute will need to be removed before the new replacement part can be installed. Line up the chute and install it used the cotter pin and flange lock nut. Replace all the components before using the snowblower.This is an authentic OEM replacement part that is sourced directly from the manufacturer. It is sold on an individual basis. The lower chute is used with snowblowers manufactured by Craftsman, Cub Cadet, Huskee, MTD, Troy-Bilt, Yard Machines, and Yard-Man.

Auger bearing flange connects to the bearing to reduce friction during operation. Replace if worn or damaged to restore smooth auger rotation. Verify fit.

Replacement oil drain plug for outdoor power equipment engines. Installs in the oil pan to seal the drain opening. Replace if stripped, cracked, or leaking.

Replacement shave plate that attaches to the bottom of the auger housing to protect the auger and housing from debris damage. Replace if cracked or worn.

Auger bearing for snow throwers supports rotating shaft movement. Replace if you hear grinding noise or auger doesn't spin smoothly. Verify fit with model.

Replacement muffler for lawn tractors. Installs on the exhaust system to reduce engine noise. Order a new one if your original is rusted, cracked, or damaged.

Replacement tire and rim assembly for chipper shredders and log splitters. Installs on wheel axle for easy equipment transport. Order when damaged or worn.

Snowblower not collecting snow on one side? This left hand auger assembly restores snow clearing performance. Rotating blades move snow to chute.

Oil drain sleeve fastener for lawn tractors and riding mowers. Secures the oil drain system. Replace if cracked, stripped, or missing for proper fit.

This hubcap is an authentic OEM replacement part sourced directly from the manufacturer for use on log splitter and chipper wheels. The hubcap covers the central opening of the wheel assembly. This prevents dirt and debris from getting into the wheel assembly. If the hubcap comes off during use or is lost when replacing tires, a new one should be installed. The machine will work without a hubcap; however, the interior wheel assembly will be open to flying debris and could be damaged if rocks or large limbs go into the wheel assembly. During routine inspection and maintenance, the hub caps should be checked for damage and to make sure they are in place.The hubcap is easily removed and replaced with a screwdriver needed to pry the old hubcap off if it is still on the machine. The new hubcap simply snaps into place. This hubcap is made of high-quality metal and is sold individually. This hubcap is designed to be used with log splitters and chippers manufactured by MTD, Cub Cadet, Troy Bilt, Husky, and Yard-Man.

The snowblower auger paddle is designed for use with various single-stage 21 MTD snow throwers and blowers. This part may also be referred to as the spiral crescent. This paddle is attached to the auger, which rotates when the engine is started. As the auger rotates, the paddle will pick up and throw the snow out of the way. This part may get damaged by debris or some type of accident, or it can wear down over time. Replace a broken or worn out snowblower paddle with a genuine OEM replacement paddle. This is an OEM replacement part from MTD that fits various models of snowblowers. It can be used with compatible models from Yard Machines, Yard-Man, Troy-Bilt, Husky, Ryobi, Bolens, and MTD machines. There are over 150 models in total that this paddle can work with. It is made out of durable rubber and comes sold individually. There are two screws at each end required for mounting, which are sold separately.