Columbia Parts

This is a genuine OEM clamp sourced directly from the manufacturer. It is used in various lawn and garden machines to connect hoses to fittings. It is used to connect piping to water pumps, exhaust pipes to exhaust manifolds, and other similar applications. This connection prevents fluids or air from leaking from the hose. Clamps may be spring or screw/band clamps. Spring clamps require no tools to install and remove; however, the size must be more accurate than when using screw/band clamps. Screw/band clamps are adjustable and can be tightened or loosened. Screw clamps should be inspected periodically to ensure tightness and that the clamps have not rusted.Hose clamps are installed approximately 1/4 inch below the end of the hose. If two clamps are used, there should be 1/4 inch between the two bands. When using a screw clamp, loosen the screw with a screwdriver just enough to fit the clamp over the hose. If using a spring clamp, squeeze the clamp and hold it open. Slide the clamp over the hose and then attach the hose and clamp to the fitting. Slide the clamp into place at the joint and tighten. Do not overtighten. This brass-colored clamp is a spring clamp made of metal; it is sold as an individual unit. This clamp is compatible with many different types of pipes made by various manufacturers.

This exhaust piping is a genuine OEM replacement part sourced directly from the manufacturer; it is used on tiller engines and other small engines. The exhaust piping is part of the muffler system. It connects to the exhaust manifold. As gas is combusted to run the engine, it is forced out through the exhaust manifold and the exhaust piping. This process heats the pipes for a short period. Over a period of time, this repeated heating can cause the exhaust piping to deteriorate. If this happens, the piping will need to be replaced in order for the exhaust manifold to function correctly. If the engine is experiencing overheating problems, the exhaust pipes will need to be replaced when it is fixed. Overheating will cause them to deteriorate much faster than normal.Allow the engine and exhaust manifold to cool before replacing the exhaust piping. Remove the exhaust pipes from the exhaust manifold. Inspect the manifold for visible signs of damage while the pipes are off. This would be a good time to replace the exhaust manifold gasket. Install the new pipes. The exhaust piping is made of durable black plastic and sold as an individual unit. It is compatible with tillers, chipper shredders, snowblowers, and other small engines manufactured by Cub Cadet, MTD, Troy-Bilt, and Yard Machines.

This fuel tank assembly can be used as a replacement part for the small engine of a snowblower or a tiller. The fuel tank assembly contains the fuel tank as well as the parts required to install the part. The purpose of the fuel tank is to store fuel for the engine and dispense the fuel in order to power the engine.A fuel tank assembly might be ordered as a complete replacement part if the fuel tank and its components suffer damage. This damage might manifest in the form of fuel leakages from punctures, holes, or corrosion to the material. If this damage affects the fuel tank and its components, it should be removed and replaced before using the appliance again. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer, MTD. It is sold individually. This fuel tank assembly is compatible with the following brands: MTD, Troy-Bilt, Yard Man, and Cub Cadet.

This is a front steering gear assembly that is used in the construction of many models of lawnmowers. It is made of metal and links the drag links with the steering shaft pinion. This creates the ability for the drag links to turn the front wheels when a user turns the steering shaft. The front steering gear is an integral part of the steering assembly and any damage to the component will require replacing it.If the front steering gear assembly is broken or damaged, a replacement will require a socket set. The main symptom of a malfunctioning or faulty gear assembly is the inability to steer the lawnmower. Put the lawnmower on a stable surface and remove the spark plug wire. The steering assembly will need to be removed from the lawnmower to access the front steering gear. Disassemble the tool to reach the gear and remove it from the equipment. Replace with a new part and reassemble other components.This is an authentic OEM replacement component that is directly sourced from the manufacturer. The front steering gear assembly is sold as a single item. It is made for use with lawn mowers manufactured by MasterCut, Craftsman, Yard-Man, Troy-Bilt, Bolens, Murray, Huskee, Yard Machines, and MTD.

This part is a replacement rim assembly. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part's intended use is to replace a broken, cracked, or otherwise defective rim assembly in lawn tractors.The rim is what seals the tire and helps to support it. If the rim becomes dented, cracked, or broken in anyway, the tire may deflate, or the wheel will not function properly. Rims are subject to significant wear and tear, particularly if the equipment is used on rough terrain or comes into contact with a hard object such as a curb. It's important when working on or near an engine to make sure the equipment is powered off and completely cooled down before starting any repairs. Access to proper tools is recommended before attempting this part installation. For more accurate information on how and where to install this rim, reference the appropriate owner's manual and specific equipment diagrams.This is an authentic OEM replacement part made of high-quality materials. This rim assembly can be used with lawn tractor models that have been manufactured by MTD, Yard Machines, Bolens, Troy-Bilt, Yard Man, and Husky. Sold individually.

This replacement part is a hex screw. This part is small but important in many different kinds of equipment. Hex screws are able to work with other small parts such as washers or nuts to ensure that components are secure within the equipment.Overtightened screws might be stripped and could fall out or get stuck in place, necessitating replacement. Over time, exposure to the elements may lead to a screw becoming worn or corroded, which may cause it to break or get stuck.This is a genuine OEM replacement part manufactured by MTD. This part is sold individually.

This part is a replacement push cap. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. If the current push cap is broken or has been misplaced, this part can be used as a replacement. It is intended for use with several lawnmower models.The push cap is attached to the wheel hub cap and fits over the end of the axle shaft. This helps to protect the end of the shaft and the attached bolt that holds the wheel into position. When working on or near an engine, always ensure that the equipment is powered off and completely cooled down before attempting to undergo any repairs. For more accurate information on how and where to install this push cap, the appropriate owner's manual and equipment diagrams should be referred to. This push cap is suitable for use on a variety of lawnmower models manufactured by MTD, Yard Machines, Craftsman, Yard Man, and Troy-Bilt. It is a genuine OEM part and thus is made of high-quality, durable materials. This part is sold individually.

This replacement part is an insulator plate. It is a genuine replacement part made by MTD. This small part is important to the overall operation of many different machines. It helps to insulate other parts inside the machine as well as allow them space to operate. A new insulator plate might be needed if the current one is missing or damaged in any way including being dented, cracked, chipped, or bent. This can be due to normal wear and tear as it is common that parts become broken overtime. Be sure to refer to the correct owner's manual before attempting to replace this part. This part is a genuine OEM replacement part. This insulator plate is sold individually and is sourced directly from the manufacturer to ensure a proper fit and long-lasting use.

This replacement part is a lens. It is a genuine replacement part made by MTD. This type of part is typically found in snow blowers and is used to protect the light bulb. This lens allows the user to see the area in front of them while working in times that are not as well lit. A new lens might be needed if the current one is damaged or missing in any way. This can be due to normal wear and tear after many years of use. If the lens is damaged it can cause harm to the light bulb and it is recommended that it be replaced as soon as possible. This deck shell is a genuine OEM replacement part to ensure long-lasting use. This part is sold individually and is sourced directly from the manufacturer to ensure proper fit.

The breather hose is designed as a valve or vent that only functions one way. It allows air into the fuel tank but ensures that no air or emissions escape the tank. When this hose is not functioning, emissions and air could be leaking from the tank and cause the engine to perform poorly or not perform at all. The hose could become cracked or damaged, or the ends could lose their seal. Either way, a replacement hose will solve the problem and get the equipment back in order. This genuine OEM replacement breather hose is made by MTD and manufactured to exact specifications. It is compatible with several engines on lawn mowers, snowblowers, and chippers from brands like Troy-Bilt, MTD, Yard-Man, Yard Machines, Bolens, Cub Cadet, and Husky. There are more than 150 compatible machines for this breather hose. This high-quality composite rubber hose is sold individually.