Parts for Speed Queen ADE3SRGS173TW01: Control Panel & Controls - Rear Control Parts

This 3-position fabric selector switch is the control behind the knob that lets you choose the fabric setting on your unit. Replacing a worn switch restores positive detents and ensures your selection is recognized instead of ignored or stuck.

• Provides three selectable fabric settings to tailor operation
• Routes the chosen setting to the timer/control
• Typical symptoms: no response when changing settings, intermittent selection, or being stuck on one mode
• Physical clues of failure: loose/no detent feel, broken shaft, or heat-discolored terminals

• Disconnect power before servicing
• Access the control console; remove the knob and retaining hardware to free the old switch
• Photograph/label wire positions and transfer each lead to the same terminals on the new switch
• Reassemble and test all three positions for proper engagement

This wire organizer assembly secures and routes the wiring at the fabric selector to reduce wear and keep connections tidy for reliable machine operation. It helps prevent chafing, pinching, and loose harness routing that can cause intermittent issues. What it does:

• Holds and routes selector-area wiring to prevent rubbing and accidental disconnection
• Reduces risk of damaged insulation from contact with moving parts
• Keeps harnesses in the correct position for consistent electrical connections
• Helps maintain safe clearance between wires and metal edges or controls

• One wire organizer assembly for the fabric selector area

• Disconnect power to the appliance before servicing to avoid electrical shock
• Reference the machine's service manual or diagram for correct routing and clip orientation
• Replace any damaged clips or wiring and ensure the organizer snaps into factory mounting points
• Avoid pinching wires when reassembling panels and verify selector operation after installation

This right-hand white panel end replaces a damaged or worn side cap to restore the washer's appearance and keep the cabinet edge protected. It fits the machine's front panel area and matches factory styling. What it does:

• Covers and protects the right-hand side edge of the front cabinet or console
• Restores the unit's finished appearance after damage, scratches, or missing trim
• Helps prevent exposure of internal edges and wiring along the cabinet side
• Matches factory color and mounting locations for a clean replacement

• Remove power and disconnect the appliance before beginning any repair.
• Minor disassembly of the front panel or console may be required to access mounting tabs.
• Handle edges carefully to avoid cutting yourself or scratching the finish.
• Replace missing or damaged fasteners with matching hardware for secure fit.

This replacement knob assembly with skirt restores a secure, easy-to-turn control interface on the appliance. It provides a finished look while allowing reliable selection of settings. What it does:

• Replaces a cracked, stripped, or missing control knob to restore user control
• Provides a stable grip and tactile feedback when turning settings
• Helps prevent accidental slips or selector misalignment caused by worn knobs
• Matches the original mounting style for a direct-fit replacement

• Disconnect power (unplug or switch off breaker) before starting any repair
• Remove the old knob by pulling straight off the control shaft; install the new knob by aligning and pushing fully onto the shaft
• If the original used a retaining clip or set screw, verify and reinstall it; only use parts explicitly included

This is a control knob for washing machines. This control knob is used to adjust the water temperature and level settings on the unit. It is manufactured out of a white plastic. The replacement is very easy and takes less than 15 minutes to complete. All that this process involves is pulling the old knob off and sliding the new knob on.A new control knob will be needed if the original is cracked, broken, or damaged in any way. Over time, the white plastic may begin to yellow, and the user may wish to replace the control knob for cosmetic purposes. If the knob is not actuating the desired cycle, it will need to be replaced.This control knob is a genuine SpeedQueen part and is an OEM part sourced directly from the manufacturer. It is sold individually. This specific control knob is compatible with washing machines that are manufactured by the SpeedQueen brand.

This left-side white panel end replaces a damaged or worn corner trim on the control console or front fascia to restore appearance and protect edges. Designed to match original fit and finish on compatible Speed Queen units. What it does:

• Covers and protects the left edge of the console/front panel from bumps, wear, and moisture.
• Restores a clean, finished look when the original panel end is cracked, chipped, or missing.
• Helps maintain proper alignment and support for adjacent trim and fasteners.
• Fits in place of the factory left-side panel end for straightforward cosmetic repair.

• Designed for direct replacement; reinstall using original screws/clips when present.
• Inspect adjacent trim and fasteners; replace any damaged clips to ensure secure fit.
• Power down and unplug the appliance before attempting any repairs that require panel removal.