Parts for Speed Queen ADE3SRGS173TW01: Cylinder Parts

This moisture sensor base positions and secures the washer's moisture sensing contacts so the control can detect fabric dampness and finish cycles correctly. Restores reliable wetness detection when the original base is damaged or worn. What it does:

• Holds the moisture-sensing probes/contacts in the correct location for accurate wetness readings.
• Passes moisture detection signals to the control so automatic cycles advance and end properly.
• Helps address symptoms like inconsistent dryness, cycles that stop too soon or run too long, or error codes related to moisture sensing.
• Use when the mounting base is cracked, corroded, or connector fit is loose.

• Disconnect power to the appliance before starting any repair to avoid shock or injury.
• Access typically requires removing the washer cabinet or access panels; keep fasteners and connectors organized.
• Handle sensor contacts carefully to avoid bending or contaminating the probe surfaces; ensure connectors are fully seated.

This replacement moisture sensor bar mounts inside the drum and helps the dryer detect when laundry is dry. A worn or damaged bar can cause sensor-dry cycles to end too soon or run too long.

• Senses moisture on fabrics and signals the control to advance or extend auto-dry cycles
• Helps stop the cycle when clothes reach the selected dryness level
• Symptoms can include auto-dry cycles ending early, extended run times, or inconsistent dryness
• Build-up on the bars can also affect sensing performance

• Disconnect power before servicing; shut off gas supply for gas dryers
• Access the sensor at the front bulkhead/lint housing; move wire leads to the new bar and secure with existing hardware
• Clean any residue from both sensor bars to improve accuracy
• Reassemble and test with a small damp load on a sensor cycle

This washer cylinder baffle mounts to the inner basket and lifts garments as the basket turns. Replacing a cracked, loose, or missing baffle restores proper turnover, reduces banging noises, and helps prevent fabric snags.

• Lifts and tumbles clothes for effective wash action
• Helps distribute the load to minimize imbalance and noise
• Guides garment movement for consistent wash action
• Common failure symptoms: loose or missing baffle, rattling/banging sounds, clothes catching or excessive wear

• Disconnect power and shut off water before servicing; wear cut-resistant gloves
• Open the door and rotate the basket to access the baffle fasteners; support the baffle while removing screws
• Align the new baffle with the keyed slots/holes and tighten the screws securely
• Manually rotate the basket to confirm clearance, then run a short test cycle to verify smooth operation

This galvanized dryer cylinder assembly replaces the drum that holds clothes and directs airflow for efficient tumbling and drying. Designed as a direct-fit replacement to restore drum integrity and proper rotation. What it does:

• Replaces a worn, dented, or corroded dryer drum to prevent fabric damage and restore normal tumbling
• Provides the rotating surface that carries clothes through the dryer's airflow path
• Helps maintain proper drum alignment and reduces rubbing noises from a damaged drum
• Restores an even tumbling action that can improve drying consistency

• Intended for DIYers; refer to your service manual for model-specific instructions
• Disconnect power and gas before beginning service to avoid shock or fire hazards
• Inspect and replace related wear items (drum seals, rollers, glides, or belt) if they show wear during installation
• Handle the drum carefully to avoid sharp edges and to protect the painted/galvanized finish

The Drying Rack is an OEM part for Speed Queen dryers. This part provides a flat, stationary surface within the dryer drum for drying items that should not be tumbled, such as shoes, hats, or delicate garments. 

Common causes of a bad drying rack include physical damage from overloading, warping from exposure to high heat, or cracks and breaks from regular use over time.

Symptoms of a bad drying rack include:

• Items not staying in place during the drying cycle
• Visible cracks, bends, or breaks in the rack
• Difficulty fitting the rack securely in the dryer drum
• Unusual noises during the drying process due to a loose or unstable rack

This OEM Speed Queen part is also compatible with some Alliance Laundry Systems models.