Parts for Speed Queen ADE3SRGS173TW01: Front Bulkhead / Air Duct / Felt Seal Parts

A clear silicone adhesive/sealant used to bond and seal appliance trim and components, helping restore watertight and stable assemblies. Supplies a durable, flexible hold for small repairs where factory adhesive is specified. What it does:

• Bonds trim, panels, and small plastic or metal parts to prevent movement and leaks
• Seals gaps to reduce water intrusion around housings and door areas
• Provides a flexible, durable hold that resists vibration and temperature changes
• Useful for reattaching trim, tabs, and molded parts when original adhesive has failed

• One (1) clear 3 oz tube of DOW 737 adhesive

• Use in a well-ventilated area; wear gloves and eye protection to avoid skin/eye contact
• Surface must be clean, dry, and free of oils or old adhesive for best adhesion
• Apply as a thin, even bead; allow recommended cure time before reassembling or using appliance
• Follow any OEM repair instructions and local disposal guidance for adhesive containers

This seal kit restores a proper water-tight barrier in the washer's drive area to prevent leaks and protect bearings and motor components on 1992-and-newer units.

• Seals the drive shaft/tub interface to stop water migration
• Helps prevent bearing and motor damage from moisture
• Common leak symptoms: water under the washer, rust streaks at center post, noisy spin from moisture intrusion
• May also address oil/water contamination around the transmission area

• Disconnect power and water; move the washer to a stable, level work area
• Removal of agitator, inner tub, and drive components is typically required
• Inspect shaft and mating surfaces; clean and lightly lubricate as specified by service literature
• Use proper drivers/press tools; do not hammer seals into place

This air duct assembly routes airflow inside the washer cabinet to support proper ventilation and cooling of internal components. It replaces damaged or cracked ducts to restore directed airflow and reduce overheating risk. What it does:

• Channels air from the blower/fan to internal areas to help dissipate heat and control moisture.
• Prevents airflow leaks that can cause poor ventilation, unusual heat buildup, or increased drying times.
• Restores proper airflow paths that may stop intermittent fan noise caused by loose or broken ducting.
• Keeps dust and lint contained within the duct path to reduce buildup on sensitive components.

• One light-gray air duct assembly

• Disconnect power to the appliance before attempting any service.
• Remove access panels as needed to reach the duct; handle plastic parts gently to avoid cracking.
• Verify alignment and secure all fasteners; ensure ducts seat properly over blower or vent connections.
• Inspect and replace as needed for best results.

This lint filter captures lint and fibers from the drying airflow to protect the blower and vent path. Replacing a damaged or missing screen helps maintain airflow, reduce lint buildup, and keep drying performance consistent.

• Traps lint and debris as air circulates through the dryer
• Helps maintain proper airflow and drying efficiency
• Replace if mesh is torn, frame is warped/cracked, or the filter won't seat fully
• Common symptoms: longer dry times, lint on clothes or around the door, or a filter that pops out

• Disconnect power; for gas models, also shut off the gas supply
• Remove the old filter from the lint opening and vacuum any lint from the housing
• Insert the new filter fully so it sits flat and seals properly
• Never operate the dryer without the lint filter installed

This Rulon 488 cylinder glide supports the front edge of the dryer drum at the bulkhead. Replacing a worn glide restores smooth, quiet rotation and helps eliminate scraping or squealing from the front of the drum.

• Provides a durable, low-friction surface between the drum rim and front bulkhead
• Supports the drum to minimize drag and wear for quieter operation
• Worn glide may cause scraping/squealing noises or a dragging drum
• Visible flat spots, grooves, or excessive wear on the glide indicate replacement

• Disconnect power and shut off gas supply before servicing
• Access the front bulkhead and support the drum to relieve load on the glide
• Remove the worn glide and clean the mounting area; install the new glide in the same position/orientation per factory fasteners
• Rotate the drum by hand to inspect felt seals and any additional glides and replace if worn

The Glide Kit is an OEM replacement part for Speed Queen dryers. Designed for models manufactured in 1992 and later, this kit ensures the drum rotates smoothly during operation. It includes glide components that reduce friction between the drum and the dryer frame, allowing efficient and quiet performance.

Symptoms of a bad Glide Kit include:

• Squeaking or grinding noises during dryer operation
• Visible wear or damage to the glides upon inspection
• The drum becoming difficult to turn or feeling misaligned

Causes of a failing Glide Kit can include natural wear and tear over extended use, overloading the dryer, or improper alignment of the drum, which increases stress on the glides.

This OEM Speed Queen part is also compatible with Alliance laundry equipment.

This 120V light housing assembly secures and protects the interior light in your machine, restoring dependable illumination inside the cabinet. It positions the bulb and socket correctly so you can clearly see the drum/compartment when the door opens.

• Mounts and insulates the interior light socket within the cabinet
• Positions the bulb for proper interior illumination
• Helps resolve issues from a cracked, heat-damaged, or loose housing
• Typical symptoms: interior light won't turn on, flickers intermittently, or only works when the door is moved
• Designed for 120V systems

• Disconnect power before servicing to avoid electrical shock
• Access the light area per your model's service information; remove panels as needed
• Note wire locations; make secure connections to the new housing
• Restore power and test the interior light before final reassembly