Parts for Ge JGBP87DEM1BB: 02 - Control Panel & Cooktop Parts

Felt pad seal cushions your range door, reducing noise and preventing rattling. Replace when worn, compressed, or damaged to restore quiet operation.

This end support holds the dryer drum in place and provides a stable mounting point for the drum shaft, helping the drum spin smoothly. Replaces a worn or broken support to reduce noise and drum wobble. What it does:

• Supports the drum shaft at t

Replace your range's cracked or missing endcap with this structural trim piece. Installs at the end of the control panel or cooktop edge for a finished look.

A replacement trim control that restores the finished look and protective edge around your appliance control area. Replaces damaged or worn trim to keep the control panel secure and cosmetically correct. What it does:

• Covers and protects the front edge of the appliance control panel from wear and debris
• Restores a clean, factory appearance when original trim is cracked, dented, or missing
• Helps keep control buttons and switches edged and aligned for normal operation
• Fits where the original trim was installed; designed to match OEM fit and form

• Disconnect power (or shut off gas and unplug) before servicing to avoid shock or injury
• Installation typically requires removal of the control panel or fascia; basic hand tools needed
• Handle edges and mounting tabs carefully to avoid scratching or cutting; wear gloves if needed

Range won't heat or display is blank? This electronic control board manages temperature and oven functions. DIY-friendly repair, typically 10 minutes.

Replace the upper back cover panel on your range. This housing component protects internal parts and completes the exterior. Order now if damaged or missing.

Replace your range's back lower cover panel if it's cracked, broken, or missing. This protective housing installs on the rear lower section of your range.

Secures components to your appliance chassis for a rattle-free fit. Replace missing, stripped, or corroded screws to keep panels and brackets aligned.

Wire harness assembly for ranges. Routes power and control signals between the control board and heating elements. Replace if wires are damaged or frayed.

If burners won't ignite automatically but light with a match, the spark module likely failed. Accessed from the back of the range, moderate difficulty.

Cast iron center burner grate for gas ranges. Sits over the middle burner on the cooktop. Replace if cracked, chipped, rusted, or damaged from wear.

Pin locator for gas ranges. Secures and aligns burner components in proper position. Replace if broken, missing, or worn to restore proper burner assembly.

Factory screw secures brackets, panels, trim, or burner components on ranges, cooktops, and wall ovens. Replaces missing, stripped, or corroded fasteners.

Cooktop mounting screw secures the cooktop to frame or brackets. Replace if stripped, missing, or rusty to eliminate wobble, rattling, or lifted corners.

Black overlay that adheres to your range control panel. Replace if cracked, damaged, or worn. Peel-and-stick installation over the control board.

Black burner cap sits atop the burner head on gas ranges and cooktops. Replace if cracked, chipped, discolored, or missing to restore appearance.

Black burner cap sits on top of your gas range burner head. Replace if cracked, chipped, stained, or missing to restore your cooktop's appearance.

Black burner cap for gas range cooktops. Replaces cracked, stained, warped, or missing caps. Sits atop burner base for proper flame distribution.

Burner cap sits on top of the range burner base to evenly distribute flame. Replace if cracked, chipped, discolored, or missing for proper cooking.

The Top Burner Spark Electrode is an OEM replacement part for GE brand appliances. Compatible with select GE gas ranges, this spark electrode ensures a reliable ignition for your burners. It features a white ceramic base and a metal electrode tip.

Symptoms of a bad igniter:

• Burners not lighting
• Igniter sparking erratically

The causes of a bad part can include physical damage or wear and tear over time.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

Replacement small surface burner for gas ranges and cooktops. Installs on stovetop to provide heat for smaller pots. Replace if damaged, discolored, or missing.

Burner base holds and secures the gas burner assembly on your cooktop. Replace if cracked, warped, or corroded to restore proper burner seating.

The Vision Burner XL is an OEM part for GE ranges. It is a large burner designed to provide high heat output for tasks that require intense cooking temperatures, such as boiling large pots of water or rapid heating. This burner ensures efficient and po

The Medium Surface Burner is an OEM part for GE ranges and cooktops. This burner is essential for a wide range of cooking tasks, from simmering sauces to sautéing vegetables. The medium surface burner ensures even heat distribution and efficient

Secures the ignition electrode on gas range burners. Replace if burners won't spark, igniter clicks continuously, or clip is corroded or loose. Confirm fit with your model number.

Package of 12

Replacement mounting screw secures panels, brackets, and trim on ranges and cooktops. Install to replace missing, stripped, or rusted fasteners.

Insulation shield that installs behind the range control panel. Protects control board and wiring from oven heat. Replace if cracked, damaged, or missing.

Flat cooking surface that fits over range burners for pancakes, eggs, and sandwiches. Replace if cracked, warped, or missing from previous owners.

Hex washer head screw for electric ranges. Secures panels, brackets, and internal components. Replace if screw is stripped, missing, or damaged.

Decorative nameplate badge for oven and range front panels. Replaces missing, worn, or damaged emblems to restore factory appearance. Includes adhesive.