Parts for Bosch WFL2090UC/01: Control Panel Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This interference capacitor suppresses electrical noise and radio-frequency interference to help the appliance's electronics run more reliably. It fits on the control board and supports stable operation by filtering stray voltage spikes. What it does:

• Filters electrical and radio-frequency interference that can cause erratic control behavior or false error codes
• Reduces electrical noise that can affect nearby audio or radio reception
• Helps protect control circuitry from transient voltage spikes
• Commonly used when appliance exhibits intermittent faults or unexplained control glitches

• Disconnect power to the appliance before starting any repair
• Discharge capacitors and avoid touching leads; use insulated tools and follow safe-handling practices
• Replace only with the exact part specified for your model and secure all wire connections firmly

This spin speed knob lets you select wash spin settings so you can adjust water extraction for different loads. It replaces a worn, cracked, or loose dial to restore clear speed selection and smooth control. What it does:

• Selects the washer's spin speed setting for proper water extraction
• Restores firm, accurate dial operation when original knob is loose or broken
• Helps prevent accidental speed changes during a cycle
• Matches OEM fit and detent locations for correct alignment

• Remove power from the appliance before attempting replacement
• Typically pulls off the control shaft; inspect for retaining clip or set screw
• If knob does not seat fully, verify shaft and index tab are undamaged

This dispenser door is the outer cover for the dishwasher detergent cup, providing a secure compartment for powder or tablet detergent until the wash cycle releases it. Restores proper detergent release and keeps the cup sealed during fill and wash. What it does:

• Covers and seals the detergent cup so detergent stays dry until the cycle releases it
• Pops open at the correct time so detergent dispenses into the wash
• Replaces cracked, warped, or otherwise damaged doors that won't latch or open
• Helps prevent detergent from dissolving prematurely or leaking into the tub

• Disconnect power and water to the appliance before servicing
• Remove the inner door panel or access the dispenser per the service manual to replace the door
• Handle plastic parts carefully to avoid damage; use proper hand and eye protection

This adjustable leveling foot provides a stable, height-adjustable support for appliances, helping restore proper alignment and reduce rocking. It replaces worn or damaged feet to keep the appliance level and secure on uneven floors. What it does

• Supports and stabilizes the appliance by allowing height adjustment
• Helps eliminate rocking, tipping, or uneven gaps caused by a damaged or missing foot
• Restores proper appliance alignment for smooth door operation and even performance
• Designed for use where the OEM lists a removable/replaceable foot component

• One adjustable leveling foot

• Inspect mounting location and hardware; replace any damaged clips or screws before installing
• Hand-start threads, then tighten with appropriate tool until secure; avoid overtightening
• Unplug or disconnect power before service if reaching into the cabinet or near wiring

2 included - Front load

Restore smooth, secure door movement with this door hinge. It supports and guides the door through opening and closing, helping ensure proper alignment and consistent sealing so the appliance operates safely and efficiently.

• Supports the door's weight and pivots for smooth opening/closing
• Helps maintain correct door alignment and gasket contact
• Wear or damage can cause sagging, misalignment, noisy operation, or incomplete closing
• Replacing a worn hinge can improve door seal and overall performance

• Disconnect power and allow the appliance to cool before service
• Support the door during removal to prevent strain on the remaining hinge
• Transfer any original fasteners to the new hinge if re-used
• Check door alignment and operation before restoring power

This door hinge bushing sits between the hinge and pivot point to reduce friction and wear. Replacing a worn bushing restores smooth, quiet door movement and helps keep the door properly aligned over time. What it does:

• Provides a smooth, low-friction pivot surface for the hinge
• Helps maintain door alignment and consistent opening/closing feel
• Reduces squeaks, grinding, or binding from the hinge area
• Replaces cracked, flattened, or missing bushing that can make the door feel loose or stiff

• 1 door hinge bushing

• Disconnect power to the appliance before servicing
• Support the door to relieve hinge tension; hinges may be spring-loaded—control door movement
• Access the hinge per your model's service information and note the bushing's orientation
• Install the new bushing, reassemble, and test door travel and latching

The Fastening Ring is an OEM part for Bosch front load washers. It secures the door boot seal to the front panel of the washer, ensuring a tight and leak-free connection. This ring is essential for maintaining the washer's seal during operation, preventing water from escaping the drum.

Causes of a bad fastening ring can include normal wear and tear, rust or corrosion, and damage from over-tightening or mishandling during maintenance.

Symptoms of a bad fastening ring include:

• Water leaking from the door area
• The door boot seal becoming loose or detached
• Visible damage or deformation of the ring

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This gray rear door panel forms the inner half of the washer door assembly. Replacing a cracked or warped panel restores door integrity, supports the glass, and helps the door seal close and latch as designed. What it does:

• Serves as the inner structure of the washer door and mates with the outer frame
• Supports and positions the door glass and related trim
• Helps maintain proper seal between the door and tub boot to minimize leaks
• Common symptoms: cracked/broken panel, difficulty latching, door misalignment, leaks at door area

• 1 rear door panel in gray

• Disconnect power and turn off water supply before servicing
• Remove the door from the hinge, then separate the door halves by removing perimeter screws/clips
• Transfer the door glass and any reusable hardware/trim to the new panel; keep orientation consistent
• Inspect the door boot lip and ensure it seats properly; verify smooth closing and latching before use

Door handle pin secures the appliance door handle to the door assembly, restoring a firm, stable grip and preventing the handle from slipping or detaching. What it does:

• Acts as the pivot/fastening pin that holds the door handle to the door or door trim.
• Replaces worn, bent, or broken pins that cause loose, wobbly, or sagging handles.
• Helps prevent the handle from falling off or catching when opening and closing the door.
• Restores proper alignment and reliable leverage for normal door operation.

• Disconnect power to the appliance before starting any work; for water-connected appliances also turn off water supply.
• Remove the handle and any trim carefully to access the pin; keep small fasteners in a safe place.
• Install the pin in the same orientation as the original; if retaining clips or bushings were present, reuse or replace them as needed.
• If you encounter springs, clips, or hidden fasteners, proceed cautiously.

The Handle Washer is an OEM part for Bosch front-loading washing machines. It provides an ergonomic grip to facilitate opening and closing the washer door. 

Causes of a bad handle washer can include cracks, chips, or breaks due to impact or regular use over time. Harsh chemicals or prolonged sun exposure can also degrade the material.

Symptoms of a bad handle washer include: 

• Difficulty gripping the handle securely  
• Sharp or rough edges pose a safety hazard
• Loose attachment making the handle unstable
• Discoloration or deterioration impacting aesthetics

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This front door panel replaces the outer frame of the washer door, restoring appearance and proper alignment. It frames the window and interfaces with the handle/latch components so the door closes and latches as designed.

• Forms the exterior frame around the door glass and completes the door assembly
• Provides alignment for door components to help ensure smooth closing and latching
• Replaces cracked, broken, or discolored outer door trim/panel
• Can help resolve issues like loose-feeling doors or doors not aligning with the latch

• Disconnect power before servicing
• Open the door, support the assembly, and remove the perimeter screws securing the outer panel
• Transfer any components attached to the old panel, position the new panel, and tighten screws evenly
• Check door alignment and latch operation before returning the appliance to service

This latch secures the appliance door closed and lets the control know when it's safe to run a cycle. Replacing a worn or damaged latch restores reliable door closure and consistent cycle starts.

• Engages the door strike to hold the door shut during operation
• May include an internal switch that signals door-closed status to the control
• Helps prevent cycle interruptions caused by a door-ajar condition
• Common symptoms: door won't latch, door pops open, cycle won't start, "door open" message or beeping

• Disconnect electrical power before servicing; shut off water supply if applicable
• Access and fasteners vary by model; latch mounts at the door/front panel area
• Transfer any mounting hardware and connectors from the original part one-for-one
• After installation, verify proper alignment with the door strike and that the unit recognizes "door closed"

The Drive Belt is an OEM part for Bosch washing machines. This belt connects the motor to the drum, enabling the drum to spin during the wash and spin cycles. This belt measures  49.4 inches and replaces a broken or damaged original belt. With 5 ribs and 4 grooves, the high-quality belt transfers drive power to rotate the drum.

Causes of a bad drive belt include normal wear and tear over time, overloading the washer, or a misalignment of the belt and pulleys. These issues can reduce the efficiency of the washing machine and cause it to malfunction.

Symptoms of a bad drive belt include:

• The drum not spinning or agitating
• Unusual noises during operation
• Burning smell from the washer
• Washer stopping mid-cycle

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This drum bearing set replaces worn bearings that support the dryer drum and enable smooth, stable rotation, restoring quieter operation and reducing wobbling, grinding, or squealing caused by failed bearings. What it does:

• Supports and stabilizes the drum shaft to maintain smooth drum rotation.
• Replaces worn or noisy bearings that can cause loud squealing or grinding.
• Reduces drum wobble and vibration that can lead to rubbing or uneven wear.
• Helps restore proper drum alignment for smoother operation.

• Disconnect power (unplug the appliance or switch off the circuit) before starting any repair.
• Replacement typically requires drum access/removal and basic hand tools; inspect the appliance service manual or diagram for disassembly steps.
• Inspect the shaft, seals, and surrounding components for wear while the drum is removed and replace any damaged parts.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This OEM part is a Bosch washer drum assembly. The drum is the cylindrical piece that is found inside the washer where the clothes are put. Damage to the drum cause it to not rotate properly. If the drum is making excessive noise during the wash cycle and appears to be misaligned, damaged, or broken, it might be time for a replacement. Luckily, replacing this drum is a relatively simple process. Start by removing the front panel of the washing machine. Then proceed to remove the top and back panels. After gaining access to the interior of the machine, disconnect any hoses attached to the drum and take note of where they go. Using a screwdriver, remove the screws that hold the drum to the machine. Lift the drum out, and replace it with the new one. Be sure to re-attach the hoses properly. Secure the front back and top panels of the washer. This genuine replacement drum assembly is compatible with Bosch washing machines.

This is the dishwasher inner tub — the main water-holding enclosure that supports racks and directs wash water. Replacing a damaged tub restores the cabinet's watertight integrity and prepares the appliance for safe operation. What it does:

• Houses wash and rinse water and provides mounting points for racks, spray arms, and seals
• Maintains a watertight chamber to prevent leaks and water damage
• Supports proper spray and drainage by keeping components aligned
• A cracked, warped, or punctured tub can cause visible leaks, pooling on the floor, or dishwasher failure to fill/hold water

• Disconnect power and water supply before starting; follow manufacturer service procedures
• Replacing the tub typically requires partial disassembly of the dishwasher (door, panels, and internal components)
• Handle carefully — tubs can be heavy and have sharp edges; wear gloves and eye protection

The Door Seal is an OEM part for Bosch front load washers, designed to ensure a watertight seal between the door and the drum. This part prevents water from leaking out during the wash cycle, maintaining the efficiency and safety of your appliance. 

Over time, the constant exposure to water and detergent, along with the physical stress of laundry loads, can cause the door seal to degrade. 

Symptoms of a bad Door Seal include:

• Visible signs of wear, such as cracks, holes, or tears, which can lead to water leaks.
• Mold or mildew buildup, resulting from trapped moisture and detergent residue, which can cause unpleasant odors and potential health issues.
• The door struggling to close properly or water leakage during the wash cycle, indicating a seal that has lost its elasticity or is otherwise damaged.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This door seal holding spring is the wire clamp that secures the washer's door boot to the front opening, keeping the seal seated to help prevent leaks and maintain a proper fit.

• Holds the door seal/boot firmly around the front panel opening
• Helps maintain a watertight seal during wash and spin cycles
• Replaces a stretched, broken, or missing clamp/spring
• Common symptoms: boot won't stay seated, water leaking at the door opening, visible broken/missing spring

• Disconnect power and turn off the water supply before servicing
• Open the door and carefully remove the existing clamp from the gasket groove; avoid puncturing the boot
• Reseat the boot evenly, then stretch and position the new spring/clamp around the groove (spring typically at the bottom)
• Test for leaks after reassembly

This washing machine shock absorber stabilizes the outer tub during wash and spin. Replacing a weakened damper helps control vibration and noise so the washer runs smoother and is less likely to shake, bang, or walk.

• Mounts between the tub assembly and cabinet/base to cushion movement
• Helps prevent excessive vibration, shaking, and thumping noises
• Can reduce "walking" or out-of-balance interruptions when a damper is worn
• Supports smoother, quieter spin performance

• Disconnect power and turn off water supply before servicing
• Remove the appropriate access panel(s) to reach the dampers
• Support the tub when removing mounting pins/bolts; match the original orientation
• Inspect all dampers; replace any that show wear for balanced performance

This rear drum motor mounting bushing supports the motor shaft at the back of the tub, keeping the drum aligned and reducing wear. It restores smooth drum rotation and helps reduce noise and vibration when functioning properly. What it does:

• Centers and supports the motor shaft to maintain proper drum alignment.
• Cushions rotating components to reduce squealing, grinding, or scraping noises.
• Helps prevent excess drum wobble and uneven wear on the tub and bearings.
• Can stop intermittent rubbing or burning smells caused by a worn mounting surface.

• Disconnect power before starting and follow all safety precautions; service panels may have sharp edges.
• Access typically requires removing the dryer/heater assembly and drum.
• Inspect mating surfaces and surrounding components (shaft, bearing, seal). Replace any excessively worn parts to prevent repeat failures.
• Use only OEM-recommended parts and fasteners; do not force or press the part in without proper alignment.

This front drum motor mounting bushing supports the dryer drum shaft and helps the drum spin smoothly for quiet, even drying. It replaces a worn bearing surface to reduce noise and prevent drum misalignment. What it does:

• Provides a low-friction bearing surface for the drum shaft at the front motor mount
• Helps keep the drum properly aligned during rotation
• Reduces squealing, grinding, or rubbing noises caused by a worn front bushing
• Prevents excess wear on the drum shaft and adjacent components when functioning correctly

• One front drum motor mounting bushing

• Disconnect power before beginning any repair and follow all safety precautions
• Inspect the drum shaft, drum seal, and rear bushing for wear and replace as needed
• Use appropriate tools to remove the old bushing and press or seat the new bushing evenly
• Re-check installation and related components if alignment or noise persists after replacement

This dispenser tray replaces the plastic cup that holds detergent and rinse agent inside the dishwasher dispenser assembly, restoring proper detergent placement for even cleaning and reduced residue. What it does:

• Holds detergent/rinse agent in the dispenser so it releases during the wash cycle
• Ensures proper alignment with the dispenser cover and release mechanism
• Helps prevent detergent from pooling or leaving residue on dishes when cracked or warped
• Restores correct dispenser function when the original tray is damaged or missing

• Disconnect power to the appliance before beginning any repair.
• Remove the inner door panel or dispenser bezel per your model's service instructions to access the tray.
• Replace the tray by seating it into the dispenser housing until it snaps or aligns in place; avoid forcing parts.
• After reassembly, run a short cycle to ensure proper detergent release.

This replacement dispenser housing holds the dishwasher's detergent cup and supports the dispenser mechanism so detergent is released during the wash cycle. Use it to restore proper detergent containment and release. What it does:

• Replaces a cracked, broken or warped dispenser housing that can leak or fail to secure the detergent cup
• Supports the dispenser latch and spring so the detergent cup opens at the correct time
• Prevents water intrusion into the dispenser area that can cause poor detergent release
• Helps eliminate symptoms like detergent remaining in cup, visible leakage from the dispenser area, or intermittent dispenser operation

• One dispenser housing

• Disconnect power and water supply before starting any repair
• Remove the door inner panel to access the dispenser; handle panels and fasteners carefully to avoid damage
• Inspect dispenser gasket, latch and mounting screws and replace if worn; reassemble ensuring correct alignment for the latch and cup

The Hot Water Inlet Hose is an OEM replacement part for Bosch washers. It serves as a flexible supply line that delivers hot water from an external water heating hot water heater directly to the washer. This hose plays a key role in optimizing wash performance through consistent delivery of hot water for optimal cleaning and sanitization. 

Causes of a bad hot water inlet hose can include wear and tear over time, repetitive flexing weakening the hose material, mineral buildup restricting flow, or damage due to sharp edges or crushing forces.

Symptoms of a bad hot water inlet hose include: 

• Loss or reduction of hot water during wash cycles
• Decreased cleaning ability from insufficient water heating 
• Visible kinks, cracks, or splits along the hose body
• Leaks or drips at hose connections under the washer

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Hose Clamp is an OEM part for Bosch washers. This clamp secures connecting hoses to direct water flow where needed.

Causes of a bad hose clamp can be wear and tear over time, accidental damage from maintenance or repairs, or degradation of the clamp material from chemical exposure.

Symptoms of a bad hose clamp include:

• Leaks around hose connections
• Loose or detached hoses
• Disrupted water flow impacting cleaning performance

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This fastening ring secures mating appliance components by locking parts in place to prevent movement or separation during operation. It's a simple yet essential hardware piece that helps maintain proper alignment and reliable function. What it does

• Holds mating parts together to prevent wobble, vibration, or dislocation
• Keeps seals and assemblies properly seated to reduce noise and misalignment
• Helps maintain correct component spacing for smooth operation
• Commonly replaced when the original ring is bent, worn, or missing

• Designed for use with compatible OEM assemblies; follow for correct placement
• Inspect mating surfaces and replace any damaged clips, seals, or gaskets before reassembly
• Use proper tools to avoid deforming the ring during installation; do not force into place
• Disconnect power and follow safety procedures before servicing the appliance

This fastening ring secures a rotating or stationary component in place to help prevent movement and vibration. It restores proper fit and alignment so assemblies run quietly and components stay locked in position. What it does:

• Holds shafts, bearings or housings in position to prevent axial movement
• Helps stop rattling, wobble or misalignment caused by a loose retaining component
• Maintains a secure mechanical connection between mating parts
• Used wherever a snap/retaining ring is required to lock a component on a shaft or in a bore

• Disconnect power and water before beginning any repair
• Use the correct pliers or tools for snap/retaining rings to avoid deformation
• Verify the ring matches the OEM part number and seating location before installation

This replacement hose-pressure chamber routes water to the dishwasher's pressure chamber so the machine can sense and control water level. Restores proper pressure sensing to help prevent overfilling and fill errors. What it does

• Connects the sump/water path to the pressure chamber so the water-level sensor can detect fill height.
• Replaces cracked, pinched, or collapsed hose that can cause inaccurate water-level readings.
• Commonly used when dishwasher shows overfill, won't fill correctly, or reports water-level or pressure-related errors.
• Flexible vinyl tubing designed for routing in tight spaces without kinking.

• Disconnect power and shut off the water supply before starting any repair.
• Inspect nearby fittings and the pressure chamber for wear; replace clamps if damaged.
• Push-fit or clamp the hose securely to both ports; ensure there are no kinks or sharp bends.

This holder is a replacement mounting bracket that secures a small internal component in place to restore proper alignment and support. It helps keep parts stable so the appliance operates as intended. What it does

• Secures and supports an internal component to prevent movement or misalignment
• Replaces cracked, broken, or worn mounting points that allow rattling or improper part position
• Restores stable contact where a loose component causes intermittent operation or noise
• Fits a specific OEM location; use the part number to confirm exact application

• One replacement holder/mounting bracket

• Disconnect power and water before starting any repairs
• Inspect surrounding clips or fasteners and reuse or replace as needed—this part typically snaps or screws into place
• Handle plastic mounting parts gently to avoid cracking during installation

This vent hose channels air and moisture from the appliance to the exterior vent, helping the unit vent properly and reduce excess humidity inside the cabinet. Replaces a worn or damaged vent hose to restore normal airflow. What it does

• Directs exhaust air and steam from the appliance to the vent path.
• Helps prevent moisture buildup that can cause odors or cabinet damage.
• Commonly replaced when the hose is cracked, split, collapsed, or detached.
• Resolve symptoms such as visible leaks, poor venting, or unusual odors near the appliance.

• One vent hose.

• Disconnect power and water (if applicable) before servicing; follow all safety guidelines.
• Verify hose routing and clamp positions match the OEM layout; secure with appropriate clamps.
• Inspect adjacent fittings and seals; replace any damaged clips or gaskets for a leak-free fit.

This drain reservoir is the dishwasher plumbing housing that collects and directs wastewater to the drain pump, helping prevent internal leaks and ensuring proper draining. Replace a cracked or clogged reservoir to restore reliable water flow and reduce water under the unit. What it does:

• Funnels wastewater from the tub to the drain pump so the machine can evacuate used water
• Helps contain minor spills and prevents water from reaching sensitive electronics
• Works with the drain pump and hoses to maintain proper drainage
• Commonly causes water pooling under the dishwasher, slow or no drain cycles, or visible leaks when damaged

• Disconnect power to the appliance before starting any repair
• Shut off water supply and remove lower access panels or kickplate as needed
• Handle with care to avoid damaging adjacent hoses, clips, or wiring; replace any worn seals

The Cold Water Inlet Hose is an OEM replacement part for Bosch washing machines. It serves as a flexible supply line that delivers cold water from an external plumbing source directly to the washer. This hose plays an important role in providing a balanced mix of hot and cold water flow into the unit.

Symptoms of a bad cold water inlet hose include:

• Fluctuations in water temperature during cycles  
• Issues with certain temperature settings like warm or cold not operating properly
• Visible cracking, kinking, or leaking along the hose body
• No water flow or pressure at the cold supply 

Causes of a failed cold water inlet hose can be mineral deposits clogging the line, natural wear and tear over time, or physical damage from crushing or abrasive surfaces compromising its integrity.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore washing machine models.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.