Parts for Frigidaire FTF1040AS0: 03 - Control Panel Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Fix a washer that won't start or shows a door lock light staying on. This door strike latch restores proper door locking function. DIY repair.

Suspension spring for washer drum support system. Replaces worn, stretched, or broken springs that cause excessive vibration or drum movement during cycles.

Washer won't start or stops mid-cycle? A faulty lid switch is often the cause. This safety switch tells your washer the lid is closed. 15-30 minute fix.

Fix a washer that won't advance cycles or start filling water with a new timer. Controls cycle timing and electrical components. 10-15 minute DIY repair.

This is a replacement pan-head, locking screw used to secure the top bracket on compatible Frigidaire appliances. It provides a reliable fastener that helps keep the top bracket and panels held firmly in place. What it does:

• Secures the top bracket to the cabinet or chassis to prevent bracket movement or rattling
• Restores proper alignment of top panels and trim that may be loose or sagging
• Uses a locking feature to resist loosening from vibration
• Pan head design provides a low-profile, finished appearance once installed

• One screw as shown

• Use the matching #8-32 driver or bit and tighten until snug; avoid over-torquing to prevent stripping
• Turn off power and remove panels as needed before accessing the bracket area
• Replace only with the same size and thread type to ensure secure fit
• Replace all related screws for even support

Replacement mounting screw for securing appliance panels, brackets, and internal components. Needed when original fasteners are stripped, missing, or lost.

Rotary control knob that fits onto the control shaft to select settings. Replace if your original knob is cracked, broken, worn, or missing.

This control knob replaces a worn, cracked, or missing range/stove dial so you can select heat and settings with a secure grip and clear position indicator. It restores normal operation of the control shaft. What it does:

• Fits onto the control shaft to turn the burner/oven setting and indicate the selected position.
• Restores a solid grip and visible pointer for precise adjustments.
• Common symptom fix: knob is loose, stripped, cracked, or missing and won't turn or hold a setting.
• Helps avoid accidental setting changes from a damaged or worn knob.

• Disconnect power to the appliance before service to avoid shocks or accidental heating.
• Pull the old knob straight off the control shaft; line up splines and push the new knob onto the shaft until fully seated.
• Do not force or hammer the knob onto the shaft; if it does not seat easily, verify spline alignment.
• If the control stem or switch is damaged, replace the stem/switch assembly rather than forcing a knob.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Secure hose clamp for dishwashers and washers. Replace if worn, loose, or leaking. Verify fit with your model number before ordering.

This dispenser valve assembly controls water flow to the fridge door dispenser for reliable dispensing and shutoff. It replaces a failed valve to restore proper water delivery and stop unwanted dripping or leaks. What it does

• Opens and closes the water passage when the dispenser actuator is pressed to deliver water to the glass.
• Seals the water line to prevent drips or continuous flow when the dispenser is idle.
• Helps stop intermittent dispensing or no-water issues caused by a faulty valve.
• Works with the door dispenser plumbing—electrical/connectors remain unchanged.

• Disconnect power and shut off the refrigerator water supply before starting.
• Remove the refrigerator door panel or access cover per your model's service instructions to reach the valve.
• Verify electrical connector seating and water line fittings are secure; replace any damaged tubing or seals.
• Test for leaks and proper dispensing after restoring power and water.

Water inlet hose for washers and laundry centers. Connects the water supply to your machine. Replace if cracked, torn, leaking, or damaged.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Suspension bushing for washer tub assembly. Replaces worn, cracked, or missing bushings that cause excessive noise or tub movement during cycles.

Secures washer hoses to prevent leaks and water damage. Replace if cracked, rusted, or loose to maintain proper seal. Verify fit with your model number.

Wire harness that connects the dispenser assembly in your washer. Replace if wires are frayed, connectors are damaged, or the harness is broken or missing.

Rubber isolator that cushions vibrating components in your washer. Replace if cracked, worn, or missing to restore proper mounting and reduce noise.

Wire harness for washers. Connects electrical components inside the control panel or cabinet. Replace if wires are frayed, damaged, or connectors broken.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.