Parts for Frigidaire GLER341AS1: 07 - Control Panel Parts

This dryer timer is the cycle control that advances your dryer through Timed and Auto Dry settings. Replacing a failed timer restores proper cycle progression, start/stop, and end-of-cycle shutoff.

• Advances the cam and internal contacts to move the dryer through heat, motor, and cool-down steps
• Governs run time on Timed Dry and Auto Dry cycles
• Routes power to the correct circuits in sequence; a failed timer may not advance or may stop early
• Common symptoms include timer knob not moving, dryer running indefinitely, or not starting on certain settings

• Disconnect power; for gas models, also shut off gas
• Remove knob/dial, open the console, and unmount the timer
• Label or photograph wiring; transfer wires one at a time to the new timer
• Reassemble and test both a Timed Dry and an Auto Dry cycle

The Selector Knob is an OEM part for Frigidaire appliances designed for use on various models of washers and dryers. This knob enables users to select different cycles and settings, providing essential control over the appliance's operations.

Symptoms of a failing selector knob include:

• The knob failing to engage or change settings
• Difficulty in turning or a lack of resistance
• Visual signs of wear such as cracks or breakage

Causes of selector knob deterioration typically involve continuous mechanical use, accidental impacts, or exposure to harsh environmental conditions that can weaken the plastic.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This clip is a small plastic retainer designed to secure trim and lightweight panels so they stay in place and reduce rattling or gaps. It restores proper fit and helps keep parts aligned for a finished look. What it does:

• Secures trim pieces, panels, or grill components to the appliance frame
• Prevents loose or rattling parts that can cause noise or misalignment
• Holds components in correct position so doors and panels close properly
• Replaces worn or broken clips that no longer grip reliably

• Remove power or disconnect the appliance before servicing when applicable
• Clip installs by snapping into pre-existing mounting hole or slot; no special tools usually required
• Inspect mating surfaces and replace any additional damaged fasteners for best fit

The Turn Start Switch is an OEM part for Frigidaire dryers. It is responsible for initiating the drying cycle when the switch is turned. This switch is a critical component that engages the dryer’s motor and starts the drying process, ensuring your clothes are dried effectively.

You should replace the turn start switch if it becomes faulty or unresponsive. Causes of a bad start switch can include regular wear and tear from frequent use, electrical issues, or damage due to excessive force or mishandling.

Symptoms of a bad turn start switch include:

• Dryer not starting when the switch is turned
• Intermittent starting issues
• The switch feeling loose or not engaging properly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This factory replacement screw secures panels, brackets, or trim on your appliance so parts stay tight and aligned. Swap in a new screw when one is missing or stripped to restore a solid, rattle-free fit.

• Fastens compatible panels, brackets, handles, or internal hardware
• Helps maintain proper alignment and stability
• Common fix for loose or wobbly handles/trim, rattling noises, or missing hardware
• Replace if threads are stripped, head is damaged, or corrosion is present

• Disconnect power before servicing; wear cut-resistant gloves
• Use the correct screwdriver or nut driver to avoid stripping
• Start threads by hand to prevent cross-threading
• Tighten until snug; do not overtighten

The Timer Knob Assembly is an OEM replacement part for Frigidaire electric dryers. This assembly incorporates the timer dial, stem, and mounting components that allow users to set desired drying periods.

Causes of a faulty timer knob include wear and tear of internal gears from regular cycle selections. Damage to the outer dial or stem connection points may also occur.

Symptoms include: 

• Inability to rotate timer dial through full drying options   
• Timer selections not initiating or maintaining set programs
• Dial detaching from the front panel during adjustment

This OEM Frigidaire replacement part is compatible with Electrolux, Gibson, and various Kenmore dryer models as well.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

No.8 pan head `10 - 10b x 0.50 `cr/sq drive

This is a replacement pan-head, locking screw used to secure the top bracket on compatible Frigidaire appliances. It provides a reliable fastener that helps keep the top bracket and panels held firmly in place. What it does:

• Secures the top bracket to the cabinet or chassis to prevent bracket movement or rattling
• Restores proper alignment of top panels and trim that may be loose or sagging
• Uses a locking feature to resist loosening from vibration
• Pan head design provides a low-profile, finished appearance once installed

• One screw as shown

• Use the matching #8-32 driver or bit and tighten until snug; avoid over-torquing to prevent stripping
• Turn off power and remove panels as needed before accessing the bracket area
• Replace only with the same size and thread type to ensure secure fit
• Replace all related screws for even support