Parts for Kenmore 417.40042990 (41740042990, 417 40042990): Control Panel Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This is a small plastic latch that secures the detergent or fabric softener dispenser drawer in the closed position on a front-load washer. It clicks into place to hold the drawer shut during the wash cycle and prevent leaks. Replace this latch if the dispenser drawer won't stay closed, pops open during operation, or the latch tab is cracked or broken.

Suspension spring for washer drum support system. Replaces worn, stretched, or broken springs that cause excessive vibration or drum movement during cycles.

This dispenser drawer handle trim assembly replaces the trim and handle piece on the refrigerator dispenser drawer for a clean, finished look and reliable grip. It restores proper drawer operation and user access to the dispenser area. What it does:

• Replaces damaged, cracked, or worn dispenser drawer trim and handle for improved appearance
• Provides a secure grip to open and close the dispenser drawer smoothly
• Helps keep the dispenser opening sealed and aligned for normal drawer function
• Addresses visible cosmetic damage and loose or broken handle symptoms

• High-level replacement; typically requires removing the drawer or access panel—refer to your model's service diagram
• Disconnect power to the appliance before starting work to avoid injury
• Handle parts may snap or screw into place; save any retaining clips or screws from the old part for reuse

This is a rotary or push-type selector switch that controls the water temperature setting on the washer's control panel. It routes electrical signals to the water inlet valve to select hot, warm, or cold wash and rinse cycles. Replace this switch if the washer fills with the wrong water temperature, does not respond to temperature selections, or only fills with cold or hot water regardless of the setting.

Fix a washer that won't advance cycles or stops mid-cycle with this timer control assembly. Requires main top removal and wire reconnection. 30-45 min.

This is a replacement pan-head, locking screw used to secure the top bracket on compatible Frigidaire appliances. It provides a reliable fastener that helps keep the top bracket and panels held firmly in place. What it does:

• Secures the top bracket to the cabinet or chassis to prevent bracket movement or rattling
• Restores proper alignment of top panels and trim that may be loose or sagging
• Uses a locking feature to resist loosening from vibration
• Pan head design provides a low-profile, finished appearance once installed

• One screw as shown

• Use the matching #8-32 driver or bit and tighten until snug; avoid over-torquing to prevent stripping
• Turn off power and remove panels as needed before accessing the bracket area
• Replace only with the same size and thread type to ensure secure fit
• Replace all related screws for even support

Replacement mounting screw for securing appliance panels, brackets, and internal components. Needed when original fasteners are stripped, missing, or lost.

This control knob replaces a worn, cracked, or missing range/stove dial so you can select heat and settings with a secure grip and clear position indicator. It restores normal operation of the control shaft. What it does:

• Fits onto the control shaft to turn the burner/oven setting and indicate the selected position.
• Restores a solid grip and visible pointer for precise adjustments.
• Common symptom fix: knob is loose, stripped, cracked, or missing and won't turn or hold a setting.
• Helps avoid accidental setting changes from a damaged or worn knob.

• Disconnect power to the appliance before service to avoid shocks or accidental heating.
• Pull the old knob straight off the control shaft; line up splines and push the new knob onto the shaft until fully seated.
• Do not force or hammer the knob onto the shaft; if it does not seat easily, verify spline alignment.
• If the control stem or switch is damaged, replace the stem/switch assembly rather than forcing a knob.

Secure hose clamp for dishwashers and washers. Replace if worn, loose, or leaking. Verify fit with your model number before ordering.

This dispenser valve assembly controls water flow to the fridge door dispenser for reliable dispensing and shutoff. It replaces a failed valve to restore proper water delivery and stop unwanted dripping or leaks. What it does

• Opens and closes the water passage when the dispenser actuator is pressed to deliver water to the glass.
• Seals the water line to prevent drips or continuous flow when the dispenser is idle.
• Helps stop intermittent dispensing or no-water issues caused by a faulty valve.
• Works with the door dispenser plumbing—electrical/connectors remain unchanged.

• Disconnect power and shut off the refrigerator water supply before starting.
• Remove the refrigerator door panel or access cover per your model's service instructions to reach the valve.
• Verify electrical connector seating and water line fittings are secure; replace any damaged tubing or seals.
• Test for leaks and proper dispensing after restoring power and water.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This is a rubber hose that connects the detergent or fabric softener dispenser to the wash tub, allowing dispensed products to flow into the drum during the wash cycle. Over time this hose can crack, clog, or develop leaks. Replace it if you notice detergent not reaching the tub, water leaking near the dispenser area, or visible deterioration of the hose.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Suspension bushing for washer tub assembly. Replaces worn, cracked, or missing bushings that cause excessive noise or tub movement during cycles.

Secures washer hoses to prevent leaks and water damage. Replace if cracked, rusted, or loose to maintain proper seal. Verify fit with your model number.

Wire harness that connects the dispenser assembly in your washer. Replace if wires are frayed, connectors are damaged, or the harness is broken or missing.

Replacement bushing that cushions and centers the washer's top panel. Needed when original is worn, cracked, or missing, causing panel rattles or loose fit.

Printed use and care guide booklet for your washer. Explains operation, settings, and maintenance. Replace if lost, damaged, or missing from purchase.

Lower spring tub sleeve for washers. Protects and guides the suspension spring connection to the tub. Replace if cracked, worn, or missing.

Upper spring tub sleeve for washers. This bushing cushions the suspension spring connection to the tub. Replace if worn, cracked, or missing.

Wire harness for washers. Connects electrical components inside the control panel or cabinet. Replace if wires are frayed, damaged, or connectors broken.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.