Parts for Ge WBB4500G0WW: 01 - Controls & Backsplash Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This left-hand end cap is a direct-fit replacement part that helps secure the washer's left-side assembly and restores proper cabinet/drum alignment for smoother operation and reduced vibration. What it does:

• Caps and protects the left-side end of the washer assembly to prevent wear and debris entry
• Helps maintain proper alignment of the washer drum/cabinet on the left side
• Reduces noise, rubbing, or wobbling caused by a damaged or missing end cap
• Matches OEM fit and mounting points for straightforward replacement

• Disconnect power and water to the washer before starting any repair
• Basic hand tools may be required; some disassembly of the cabinet or front panel could be needed
• Inspect adjacent components (gaskets, seals, fasteners) for wear while replacing the end cap

This right-side end cap is a replacement trim/closure piece designed for the washer cabinet to restore proper fit and finish and help keep internals protected from debris. It replaces a damaged, cracked or missing end cap. What it does:

• Covers and protects the washer's right-side edge or mounting area from dust and moisture
• Restores a flush appearance where the original end cap was cracked or broken
• Helps prevent snagging on clothing or towels from a damaged trim piece
• Can reduce rattles or vibration caused by a loose or missing end cap

• Disconnect power to the appliance before beginning any work
• Usually secured with screws or clips; basic hand tools are typically all that's required
• Align the part to the right-side mounting location and fasten securely without over-tightening

The Button is an OEM component for GE top-load washers. Located on the control panel, this button actuates a specific function such as starting or pausing the cycle. Designed for durability, the textured plastic construction withstands millions of presses over decades of use.

Symptoms of a bad button include:

• The button sticking in the depressed position  
• Failure to trigger the assigned function when pressed
• Cracks developing in the plastic face over time

Causes may consist of cracked circuitry behind the panel from water intrusion or repeated impact. General wear reducing button sensitivity also occurs.

This GE button restores full operation for select models including those by Hotpoint, RCA, and compatible Kenmore lines. 

This knob assembly replaces a worn, cracked, or missing control knob to restore reliable user control and a finished appearance. It snaps or mounts onto the control shaft to allow easy temperature or function selection. What it does

• Replaces damaged or broken control knob that is loose, cracked, or won't turn smoothly
• Allows the user to select settings by turning the control shaft with firm tactile feedback
• Restores cosmetic finish and consistent control operation
• Fits and engages the control shaft to transmit user input to the switch or valve

• Disconnect power to the appliance before servicing; for gas models, shut off gas supply and follow all safety precautions
• Most installations require pulling the old knob straight off the shaft and pushing the new knob into place; some models may use a retaining clip or set screw
• Avoid forcing the knob; align splines or D-shaft flat before seating to prevent damage

This power line filter sits between household AC and the washer's internal wiring to reduce electrical interference and help stabilize control operation. Replacing a failed filter may restore power and prevent nuisance breaker or GFCI trips.

• Filters incoming AC power to reduce electromagnetic interference reaching the control and motor circuits
• Helps prevent interference-related issues like erratic controls or random resets
• Failure may present as no power/blank display, intermittent power loss, or tripping a breaker/GFCI
• Visual clues of failure can include scorching, swelling, or a cracked housing

• Unplug the washer or switch off the circuit breaker before servicing; allow a few minutes for internal components to discharge
• Access the filter location (often near the control area or rear panel) per your model's service information
• Note wire locations (LINE, LOAD, and GROUND) and move one lead at a time to avoid miswiring
• Mount securely and ensure the ground connection to the cabinet is tight for proper operation

Control board assembly (mounted) that replaces a failed electronic controller to restore an appliance's control functions and address unresponsive controls or erratic operation on compatible models. What it does:

• Serves as the appliance's main electronic control, accepting inputs from buttons/touchpads and sensors to operate motors, valves and displays.
• Fixes common symptoms such as blank or unresponsive controls, intermittent or no power, and unexpected cycles or behavior.
• Replaces damaged or burnt circuit board components that can cause control failures.
• Designed as a direct-fit replacement for the listed OEM board to recover normal automated functions.

• Disconnect power to the appliance before beginning; verify power is off with a meter.
• Photograph wire harness locations before removal to ensure correct reconnection.
• Handle the board by its edges and avoid touching components; observe ESD precautions where possible.

Size: 8-18 b.

This is a 8-18 x 1/2 inch hex washer head screw used to secure appliance panels and components. It provides a reliable, corrosion-resistant fastener for repair or reassembly tasks. What it does:

• Fastens panels, brackets or trim where an 8-18 x 1/2" screw is specified
• Hex washer head offers wider bearing surface to prevent pull-through
• Stainless finish resists rust and corrosion in humid appliance environments
• Restores proper fit and function when original screw is missing or damaged

• One 8-18 x 1/2 in. hex washer head stainless screw

• Use the correct driver/socket to avoid stripping the head
• Tighten securely but avoid over-torquing to prevent damage to plastic or thin metal parts
• Disconnect power and follow appliance safety precautions before working inside the unit
• Replace only with the same size and head style for proper fit

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This is the drain solenoid housing for a dishwasher. It secures and aligns the drain solenoid on the pump assembly so the drain valve actuates consistently and the tub can empty at the right time.

• Positions and insulates the drain solenoid on the pump/drain mechanism
• Maintains proper alignment for reliable drain-valve actuation
• Common symptoms of a failed housing: won't drain or drains intermittently
• May present as loud humming from the solenoid or visible cracks/heat damage on the housing

• Disconnect power and water supply before servicing
• Access the pump area beneath the tub; note solenoid, lever, and linkage orientation
• Transfer the existing solenoid and any clips/brackets to the new housing; reuse fasteners
• Run a short cycle to ensure proper draining after reassembly

This harness plug connects the dishwasher's wiring to the water inlet valve. Replacing a burnt, brittle, or loose connector restores a solid electrical connection so the valve energizes correctly and the tub fills when the cycle begins.

• Provides a secure, keyed connection between the harness and water inlet valve terminals
• Helps resolve no-fill or intermittent fill caused by heat damage, corrosion, or loose contacts at the connector
• Supports proper valve operation to reduce humming-without-fill complaints
• Useful when replacing a damaged plug during valve or harness service

• Disconnect power at the breaker and shut off water supply before servicing
• Note wire orientation; transfer or splice leads per appliance wiring and connector design
• Seat the plug fully on the valve and ensure tight, insulated connections
• Restore power and run a fill test; check for leaks at the valve and hose connections

8-18 hi/lo 5/8

These GE screws are a 12-pack of OEM replacement parts responsible for securing and fastening various components and panels in a GE range or oven. These screws are designed with a hexagonal head, which allows for the use of a compatible wrench or socket for tightening. They are commonly used to attach sheet metal panels, brackets, and other parts within the appliance, ensuring that these components remain securely in place during operation.

This part fixes the following symptoms:

• Loose or wobbly parts or panels within the appliance's interior or exterior
• Panels or components falling out of place, creating gaps or exposing internal parts
• Unusual noises or rattling sounds during the appliance's operation

The GE screws can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.

This hose clamp kit secures the washer's hoses at the pump, tub, or valve connections, helping stop leaks and hose blow-offs. Replace worn or missing clamps to restore a tight, reliable seal during fill, wash, and drain.

• Secures drain, pump, and fill hoses to fittings to maintain a watertight seal
• Helps prevent drips, leaks, and hoses slipping off during vibration
• Replaces clamps that are rusted, stripped, deformed, or missing
• Common symptoms: water leaking at hose joints, loose hose connections, clamp won't tighten
• Useful when installing a new hose, pump, or valve

• Unplug the washer and turn off water supplies; have towels or a pan ready for residual water
• Release and remove old clamps; seat the hose fully over the fitting before installing new clamps
• Tighten evenly and do not overtighten to avoid hose or fitting damage
• Restore power and water, then run a short cycle to check for leaks at each connection

The Water Inlet Valve is an OEM part for GE washing machines. This component is crucial for controlling the flow of water into the washer during the wash and rinse cycles. It works by opening and closing the solenoids to allow the appropriate amount of hot or cold water to enter the washing machine, based on the selected settings.

Symptoms of a failing Water Inlet Valve include:

• The washing machine not filling with water or filling very slowly
• The washer filling with water even when it is turned off
• Water leaking from the valve area
• The washing machine displaying error codes related to water supply issues
• Inconsistent water temperatures during cycles

Causes of a bad water inlet valve can include mineral deposits or debris clogging the valve, wear and tear on the solenoid coils, or electrical issues such as faulty wiring or connections.

This OEM GE part is also compatible with some models from Hotpoint, RCA, and Kenmore.

Includes 12 washers.

The Washer Fill Hoses are OEM parts for various washing machines, specifically designed to transport hot and cold water from the home's supply lines to the washer. These hoses are essential for the proper functioning of the washing machine, ensuring a steady and reliable flow of water during the wash and rinse cycles. Coming in packs of 2, each hose measures 5 ft.

Causes of bad washer fill hoses can include wear and tear over time, exposure to high water pressure, or damage from kinks and bends. Additionally, hoses can deteriorate due to exposure to harsh water conditions or chemical buildup.

Symptoms of bad washer fill hoses include:

• Leaks or puddles around the washing machine
• Reduced water flow into the washer
• Visible cracks or bulges in the hoses
• The washer taking longer than usual to fill with water

These washer fill hoses are compatible with a variety of washing machine brands and models, ensuring a secure and efficient water supply.

The Pressure Switch Hose is an OEM part for GE washing machines. It connects the pressure switch to the tub, allowing the switch to monitor the water level within the washing machine. This ensures the proper amount of water is used during each cycle for efficient washing and rinsing.

You should replace this pressure switch hose if it becomes cracked, clogged, or otherwise damaged. Common causes of a bad hose include wear and tear from repeated use, buildup of detergent or debris, and damage from improper handling or installation.

Symptoms of a bad pressure switch hose include:

• Washing machine not filling with water
• Overfilling or underfilling of the tub
• Inaccurate water level detection
• Error codes related to water level issues

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.