Parts for Ge WPRE8320H2WT: 01 - Controls & Backsplash Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This right-side end cap is the molded exterior trim piece that finishes the appliance cabinet and protects internal edges. It restores a clean, finished appearance and helps keep door and panel seams sealed from dirt and moisture. What it does:

• Covers and protects the outer edge on the right side of the cabinet, preventing exposure of internal components
• Restores a flush, factory-finish look when a cracked or missing end cap causes gaps or rough edges
• Helps maintain proper panel alignment and visual symmetry on the appliance exterior
• Reduces dirt and moisture intrusion where panels meet, supporting overall cabinet integrity

• One right-side end cap (white), as shown

• Designed for snap- or screw-fit installation; remove power and follow manufacturer disassembly steps before replacing
• Verify orientation (right side) and matching color before starting; handle trim pieces gently to avoid cracking
• Use basic hand tools; keep fasteners and any retainer clips for reuse or replace if damaged

The Button is an OEM component for GE top-load washers. Located on the control panel, this button actuates a specific function such as starting or pausing the cycle. Designed for durability, the textured plastic construction withstands millions of presses over decades of use.

Symptoms of a bad button include:

• The button sticking in the depressed position  
• Failure to trigger the assigned function when pressed
• Cracks developing in the plastic face over time

Causes may consist of cracked circuitry behind the panel from water intrusion or repeated impact. General wear reducing button sensitivity also occurs.

This GE button restores full operation for select models including those by Hotpoint, RCA, and compatible Kenmore lines. 

This control knob assembly replaces a worn or broken oven/stove knob so you can set burner and oven controls accurately. It restores tactile control and a clean, finished look to your appliance's control panel. What it does:

• Replaces a damaged or missing control knob to allow reliable selection of heat settings
• Restores a secure fit and tactile feedback for smooth turn-and-click operation
• Helps prevent accidental slips that can make temperature or burner selection difficult
• Matches white control panels for a factory-fresh appearance

• One white knob assembly

• Turn appliance power off before installing; disconnect power at the breaker for electric ranges
• Pull old knob straight off the control shaft and press new knob onto the shaft until fully seated
• If fit feels loose or the knob does not engage, verify shaft style (slotted vs. D-shaft) before forcing

This power line filter sits between household AC and the washer's internal wiring to reduce electrical interference and help stabilize control operation. Replacing a failed filter may restore power and prevent nuisance breaker or GFCI trips.

• Filters incoming AC power to reduce electromagnetic interference reaching the control and motor circuits
• Helps prevent interference-related issues like erratic controls or random resets
• Failure may present as no power/blank display, intermittent power loss, or tripping a breaker/GFCI
• Visual clues of failure can include scorching, swelling, or a cracked housing

• Unplug the washer or switch off the circuit breaker before servicing; allow a few minutes for internal components to discharge
• Access the filter location (often near the control area or rear panel) per your model's service information
• Note wire locations (LINE, LOAD, and GROUND) and move one lead at a time to avoid miswiring
• Mount securely and ensure the ground connection to the cabinet is tight for proper operation

This mounted control board assembly replaces the appliance's main electronic control to restore reliable operation and control of cycles and user interface functions. It provides the integrated circuitry needed for timed operations and component control. What it does:

• Replaces the unit's primary electronic control that regulates cycles, timers, and outputs
• Restores control when the appliance won't start, fails to run cycles, or shows control/interface errors
• Helps resolve intermittent operation, unresponsive buttons, or incorrect cycle behavior tied to control faults
• Interfaces with sensors, switches, and relays to coordinate heating, motors, and timers

• Disconnect power to the appliance before beginning any repair
• Handle the board by its edges and avoid static discharge; wear an ESD strap if available
• Document or photograph wire locations before disconnecting connectors for correct reassembly
• Follow OEM service instructions for access, replacement, and functional testing after installation

Size: 8-18 b.

This is a 8-18 x 1/2 inch hex washer head screw used to secure appliance panels and components. It provides a reliable, corrosion-resistant fastener for repair or reassembly tasks. What it does:

• Fastens panels, brackets or trim where an 8-18 x 1/2" screw is specified
• Hex washer head offers wider bearing surface to prevent pull-through
• Stainless finish resists rust and corrosion in humid appliance environments
• Restores proper fit and function when original screw is missing or damaged

• One 8-18 x 1/2 in. hex washer head stainless screw

• Use the correct driver/socket to avoid stripping the head
• Tighten securely but avoid over-torquing to prevent damage to plastic or thin metal parts
• Disconnect power and follow appliance safety precautions before working inside the unit
• Replace only with the same size and head style for proper fit

This is the drain solenoid housing for a dishwasher. It secures and aligns the drain solenoid on the pump assembly so the drain valve actuates consistently and the tub can empty at the right time.

• Positions and insulates the drain solenoid on the pump/drain mechanism
• Maintains proper alignment for reliable drain-valve actuation
• Common symptoms of a failed housing: won't drain or drains intermittently
• May present as loud humming from the solenoid or visible cracks/heat damage on the housing

• Disconnect power and water supply before servicing
• Access the pump area beneath the tub; note solenoid, lever, and linkage orientation
• Transfer the existing solenoid and any clips/brackets to the new housing; reuse fasteners
• Run a short cycle to ensure proper draining after reassembly

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This harness plug connects the dishwasher's wiring to the water inlet valve. Replacing a burnt, brittle, or loose connector restores a solid electrical connection so the valve energizes correctly and the tub fills when the cycle begins.

• Provides a secure, keyed connection between the harness and water inlet valve terminals
• Helps resolve no-fill or intermittent fill caused by heat damage, corrosion, or loose contacts at the connector
• Supports proper valve operation to reduce humming-without-fill complaints
• Useful when replacing a damaged plug during valve or harness service

• Disconnect power at the breaker and shut off water supply before servicing
• Note wire orientation; transfer or splice leads per appliance wiring and connector design
• Seat the plug fully on the valve and ensure tight, insulated connections
• Restore power and run a fill test; check for leaks at the valve and hose connections

Harness to corset & shifter

8-18 hi/lo 5/8

This hose clamp kit secures the washer's hoses at the pump, tub, or valve connections, helping stop leaks and hose blow-offs. Replace worn or missing clamps to restore a tight, reliable seal during fill, wash, and drain.

• Secures drain, pump, and fill hoses to fittings to maintain a watertight seal
• Helps prevent drips, leaks, and hoses slipping off during vibration
• Replaces clamps that are rusted, stripped, deformed, or missing
• Common symptoms: water leaking at hose joints, loose hose connections, clamp won't tighten
• Useful when installing a new hose, pump, or valve

• Unplug the washer and turn off water supplies; have towels or a pan ready for residual water
• Release and remove old clamps; seat the hose fully over the fitting before installing new clamps
• Tighten evenly and do not overtighten to avoid hose or fitting damage
• Restore power and water, then run a short cycle to check for leaks at each connection

The Water Inlet Valve is an OEM part for GE washing machines. This component is crucial for controlling the flow of water into the washer during the wash and rinse cycles. It works by opening and closing the solenoids to allow the appropriate amount of hot or cold water to enter the washing machine, based on the selected settings.

Symptoms of a failing Water Inlet Valve include:

• The washing machine not filling with water or filling very slowly
• The washer filling with water even when it is turned off
• Water leaking from the valve area
• The washing machine displaying error codes related to water supply issues
• Inconsistent water temperatures during cycles

Causes of a bad water inlet valve can include mineral deposits or debris clogging the valve, wear and tear on the solenoid coils, or electrical issues such as faulty wiring or connections.

This OEM GE part is also compatible with some models from Hotpoint, RCA, and Kenmore.

Includes 12 washers.

The Washer Fill Hoses are OEM parts for various washing machines, specifically designed to transport hot and cold water from the home's supply lines to the washer. These hoses are essential for the proper functioning of the washing machine, ensuring a steady and reliable flow of water during the wash and rinse cycles. Coming in packs of 2, each hose measures 5 ft.

Causes of bad washer fill hoses can include wear and tear over time, exposure to high water pressure, or damage from kinks and bends. Additionally, hoses can deteriorate due to exposure to harsh water conditions or chemical buildup.

Symptoms of bad washer fill hoses include:

• Leaks or puddles around the washing machine
• Reduced water flow into the washer
• Visible cracks or bulges in the hoses
• The washer taking longer than usual to fill with water

These washer fill hoses are compatible with a variety of washing machine brands and models, ensuring a secure and efficient water supply.

The Pressure Switch Hose is an OEM part for GE washing machines. It connects the pressure switch to the tub, allowing the switch to monitor the water level within the washing machine. This ensures the proper amount of water is used during each cycle for efficient washing and rinsing.

You should replace this pressure switch hose if it becomes cracked, clogged, or otherwise damaged. Common causes of a bad hose include wear and tear from repeated use, buildup of detergent or debris, and damage from improper handling or installation.

Symptoms of a bad pressure switch hose include:

• Washing machine not filling with water
• Overfilling or underfilling of the tub
• Inaccurate water level detection
• Error codes related to water level issues

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.