Parts for Hot Point MTAP1100F0WW: Controls & Backsplash Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

White plastic end cap for washer door trim. Covers the left edge to restore finished appearance. Replaces cracked, broken, or missing caps.

Right-side endcap for top-load washers. Replaces cracked, broken, or missing plastic endcaps on the washer cabinet. Restores finished appearance.

The Compression Ring is an OEM part for GE washing machines. This ring is essential for securing the tub within the washing machine, ensuring it remains in place during the wash and spin cycles. It helps maintain the stability and proper function of the washing machine.

You should replace the compression ring if it becomes worn, cracked, or damaged. Causes of a bad compression ring can include frequent use, high-stress loads during wash cycles, or physical damage, which can lead to instability and poor washing performance.

Symptoms of a bad compression ring include:

• Excessive shaking or movement of the washing machine during cycles
• Unusual noises during operation
• The washing machine tub appearing misaligned or loose
• Ineffective washing due to instability

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Labeled control ring for your washer's control panel. Replace when the original dial becomes cracked, stripped, worn, or the cycle indicators are unreadable.

Control knob assembly for washer timer/cycle selector. Restores secure grip when original is cracked, stripped, or broken. Attaches to timer shaft.

Secures the timer knob to the shaft for accurate cycle selection. Replace if worn, broken, or lost causing knob to spin freely. Confirm fit with model.

Fix washer overfilling or not filling properly. This pressure switch controls water level for proper washing. DIY-friendly, takes about 5-10 minutes.

Replacement control knob for washing machines. Installs on the control panel to select cycle and temperature settings. Needed when cracked or broken.

Washer timer shield protects internal timer components from moisture and debris. Simple DIY fix restores proper cycle timing and control operation.

The Knob Clip is an OEM part for GE washing machines and dryers. This small but crucial component is designed to secure the control knob to the appliance's control panel.  

Over time, knob clips can wear out or break due to frequent use or accidental damage. When this happens, the control knob may become loose, fall off easily, or fail to engage the control panel properly, making it difficult to set the appliance to the desired cycle or function.

Symptoms of a bad Knob Clip include:

• The control knob is loose or falls off the panel easily.
• Difficulty in adjusting settings due to a loose knob.
• The knob does not stay in place or slips when turned.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Size: 8-18 b.

Fix a washer that won't fill with hot or cold water. This rotary temperature switch controls water temperature settings. Easy 5-minute DIY repair.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Fix a washer that won't advance cycles, spins continuously, or has erratic operation. This timer controls wash, rinse, and spin cycles. 10-minute DIY.

Stainless steel hex washer head screw for securing appliance panels, brackets, and trim. Replace missing, stripped, or corroded fasteners during repair.

Plastic housing that secures the drain solenoid to the pump assembly. Replace if cracked, broken, or missing to properly position the solenoid mechanism.

Harness to corset & shifter

10-18 hex washer screw for securing panels, trim, brackets, and components in appliances. Replaces lost, stripped, or corroded fasteners.

Secures washer hoses at pump, tub, and valve connections to prevent leaks and hose blow-offs. Replace worn or missing clamps for a tight seal. Confirm fit.

Guides water from the inlet valve into the wash tub. Replace if cracked, broken, leaking, or causing uneven water distribution in your top-load washer.

Washer won't fill, leaks after cycles, or has no hot water? The triple water valve controls fill, rinse, and dispenser flow. DIY fix in under 1 hour.

Connects the pressure switch to the tub in top-load washers. Replace if cracked, punctured, or brittle to restore proper water level monitoring.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.