Parts for Frigidaire DGHF2360PF2A: 06 - Cooling System Parts

Molded plastic air deflector that directs cold airflow inside your refrigerator. Replace this part if cracked, broken, or missing to restore proper venting.

Refrigerator not cooling properly? This condenser coil assembly removes heat from refrigerant to restore cooling performance and improve efficiency.

This evaporator block is the refrigerator evaporator coil assembly that removes heat from the freezer/refrigerator compartment to help maintain proper cooling and reduce frost buildup. What it does:

• Circulates refrigerant through the evaporator to absorb heat from the compartment
• Promotes cold airflow across the freezer and fresh-food sections when paired with the evaporator fan
• Helps control frost and ice buildup on the evaporator surface
• Common symptoms: reduced cooling, excessive frost or ice buildup, or warm freezer temperatures

• Always disconnect power to the appliance before servicing
• Replacing the evaporator typically requires accessing sealed refrigerant areas;
• Allow components to fully defrost and drain before removal to avoid water damage
• Handle the coil gently to avoid bending fins or damaging tubing

Includes service line.

Connects your refrigerator to the wall outlet to supply electricity. Replace if the original cord is frayed, damaged, or has exposed wires from wear or moving.

Fix frost buildup on evaporator coils causing warm temps or freezer icing. This defrost heater melts accumulated ice. DIY repair in 30-40 minutes.

Aluminum strap secures the defrost heater against the evaporator coil. Replace if broken, cracked, or missing to maintain proper heater contact.

Replace your refrigerator door gasket to restore a tight seal, maintain proper cooling, and reduce energy costs. Prevents cold air leaks and frost buildup.

Fix inconsistent cooling or frost buildup with this refrigerator thermistor. Monitors internal temperature for accurate cycle control. Easy DIY repair.

Replacement screw for securing panels, components, and assemblies in appliances. Needed when original screws are stripped, lost, or damaged during repair.

Ice buildup in your freezer? This defrost thermostat monitors temperature and triggers defrost cycles. Fixes frost on rear panels and ice maker areas.

Rubber grommet that mounts and cushions the compressor to reduce vibration transfer. Replace if cracked, worn, or missing to restore quiet operation.

Secures the compressor to the mounting bracket in your refrigerator or freezer. Replace if missing, stripped, or corroded during compressor service.

Replacement defrost drain pan that collects and channels meltwater from the automatic defrost cycle. Replace if cracked, warped, or missing to prevent leaks.

Fix a refrigerator that's not cooling or running constantly with this compressor kit. Includes essential components for sealed system repair.

The Control Board is an OEM replacement part for Frigidaire refrigerators. This component serves as the brain of the appliance, managing and coordinating various functions such as temperature control, defrost cycles, and the operation of fans and compressors. A functional control board ensures the refrigerator maintains optimal performance and energy efficiency.

Control boards can fail due to power surges, electrical issues, or normal wear over time. A malfunctioning board can disrupt the refrigerator's functionality and impact its ability to preserve food effectively.

Symptoms of a bad control board include:

• Inconsistent or incorrect temperatures in the refrigerator or freezer
• Unresponsive controls or display panel issues
• The refrigerator not cooling or running continuously
• Error codes or unusual noises during operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Rubber grommet that cushions and protects door components in your refrigerator. Replace if cracked, worn, or missing to restore proper door function.

This #8-32 x 3/8 screw secures appliance panels, brackets, and assemblies. Replace a missing or stripped fastener to keep parts tight and aligned, reduce vibration, and restore proper fit in compatible refrigerators and freezers.

• Machine-thread fastener sized #8-32, 3/8-inch length
• Secures control housings, trims, covers, and support brackets per model design
• Replaces missing, worn, or corroded screws that cause loose or rattling parts
• Helps maintain alignment and stability after service

• Unplug the appliance; shut off water if applicable
• Match thread size to the original and start by hand to avoid cross-threading
• Use the correct driver; do not overtighten, especially into plastic
• Verify component alignment and operation after fastening

• Thread size: #8-32
• Length: 3/8 inch

Secures and protects wiring harness from strain damage. Replace if cracked, broken, or wires show wear. Verify fit with your model number listed.

Factory fastener that secures panels, brackets, and internal components. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattling.

This electronic main control board manages and distributes power to the appliance's key components. Replace a failed board to restore normal operation when the unit won't power up, won't start, or runs erratically.

• Regulates and routes incoming power to motors, fans, compressors, heaters, and valves based on signals from sensors and the user interface
• Coordinates cycle timing and system protections to help prevent component damage
• Logs or triggers fault indications when abnormal conditions are detected
• Common failure symptoms: no power, dead/unresponsive controls, intermittent shutdowns, or unpredictable operation

• Disconnect power at the breaker or unplug the appliance before servicing
• Handle the PCB by the edges and use ESD protection to avoid static damage
• Photograph wiring and move connectors one at a time to the new board
• Inspect connected loads (motors, heaters, compressor, valves) for shorts before restoring power

Replacement mounting screw secures panels, brackets, and trim inside refrigerators and freezers. Restores factory assembly when original fasteners are missing.

Positions the condenser fan and motor in the rear machine compartment. Replace if cracked, warped, or damaged to restore proper airflow direction.

Refrigerator not cooling or making loud grinding noise? The condenser fan motor drives airflow to cool refrigerant. DIY repair in 30-60 minutes.

Refrigerator not cooling properly? A damaged condenser fan blade prevents airflow over the condenser coils. Quick DIY fix—simply push into place.

Secures the evaporator or condenser fan shroud to the refrigerator cabinet. Replace this mounting screw if stripped, missing, or broken during repair.

Supports the compressor on the refrigerator's rear base. Replace if cracked, broken, or worn to keep compressor properly seated and reduce vibration damage.

Metal rivet fastener permanently secures panels, brackets, and internal components in refrigerators. Replace damaged, missing, or worn rivets to restore fit.

Channels defrost water from the evaporator to the rear drain pan. Replace this tube if it's cracked, clogged, missing, or has become brittle over time.

Positions and secures condenser tubing to maintain proper spacing. Replace if worn, broken, or missing to prevent vibration, rattling, and tube damage.

This tube connector is a small water-line fitting that joins refrigerator water and ice-maker tubing, restoring a secure path for water flow. It helps stop leaks and regain consistent water delivery to the dispenser or icemaker. What it does:

• Joins two sections of refrigerator water tubing to maintain a watertight connection
• Stops leaks at a damaged or worn tube joint
• Restores water flow to the ice maker or dispenser when a broken connector is the cause
• Compatible with rigid and soft tubing in typical refrigerator plumbing layouts

• One tube connector

• Shut off the refrigerator water supply before servicing
• Inspect tubing ends and replace damaged tubing or seals as needed
• Use proper fittings and tighten to manufacturer torque; avoid over-tightening

Fixes incorrect temperature readings and short cycling. This thermistor monitors fridge temps and signals the control board. Moderate DIY repair.

Foam seal tape creates airtight barriers around refrigerator components. Replace when worn, compressed, or damaged to restore proper sealing and efficiency.

Wiring harness for refrigerators. Connects electrical components inside the unit. Replace if wires are frayed, connectors are damaged, or melted.

Connects dispenser controls and components in the refrigerator door. Replace if the wiring is damaged, frayed, or causing intermittent dispenser operation.

Replacement mounting screw for refrigerator panels, handles, brackets, and internal fixtures. Order when original screws are stripped, lost, or damaged.