Craftsman Chainsaw Parts

Replacement bar adjustment pin for chainsaw clutch cover assembly. Connects adjustment screw to guide bar for chain tensioning. Replace if missing or broken.

The carburetor kit contains the essential internal components needed to rebuild or replace the carburetor on a small gas-powered engine. The carburetor mixes air and fuel in the correct ratio to keep the engine running smoothly and efficiently. Use this kit if your equipment is hard to start, runs roughly, stalls frequently, or the engine surges and won't hold a steady speed.

This baffle plate is a genuine Husqvarna part, sold individually. This baffle plate can be used as a replacement part in a string trimmer of a pole pruner. The purpose of the baffle plate in a string trimmer or a pole pruner is to control and regulate the amount of heat that is retained within the appliance.If the baffle plate shows signs of damage or reduced efficacy, the baffle plate should be removed and replaced by this genuine OEM replacement part in order to guarantee safe use of the appliance by its operator.Sourced directly from the manufacturer, this component is a genuine replacement part that is sold individually. This baffle plate is compatible with the following outdoor appliance brands: Husqvarna, Craftsman, Weed Eater, Poulan, and Poulan Pro.

Chain tensioner pin for chainsaws. Installs in the tensioning mechanism to place tension on the bar when adjusted. Replace if bent, worn, or missing.

Fix a noisy clutch or chain that won't move with this clutch drum assembly. Engages the chain around the bar when the clutch is activated. DIY repair.

Replace a worn starter hub if your chainsaw won't start or the pull cord spins freely without engaging the engine. Simple repair in 15-20 minutes.

If your trimmer won't start when pulling the cord, the starter pawl may be worn or broken. This small part engages the engine during pulls.

Connects carburetor to adapter on gas trimmers. Replace if cracked, brittle, or causing air leaks and poor engine performance. Verify fit with your model.

The carburetor is the part of the chainsaw that mixes air from the intake valve system and gas before the fuel mixture goes to the engine. This ensures that the chainsaw is capable of continuing to run while it is in use. A bad carburetor will cause problems with how the chainsaw runs, and it may stop running during work. If the engine does not start when the tank is full of fresh fuel, test the carburetor. Start by removing the air filter and pouring a teaspoon of fuel onto the carburetor. Then, pull the starter rope to start the engine. If the engine starts but quickly dies, it means that the carburetor will likely need to be replaced. The replacement of the new carburetor is fairly simple. Remove the rear cover on the chainsaw to remove the old carburetor. Once you have removed the old carburetor, you can then install the new carburetor. Replace the cover and test the chainsaw. This is an OEM sourced part that will work with several models of chainsaws from Poulan and Craftsman.

Pleated air filter captures debris before it reaches the carburetor and engine. Replace when dirty or clogged to maintain performance. Verify fit using your model number.

Replacement flywheel assembly for gas chainsaws. Mounts to the crankshaft with magnets that generate ignition charge. Replace if cracked or damaged.

This lever control is a genuine Husqvarna part, sold individually. This lever control can be used as a replacement part for a lawnmower. The lever control regulates the throttle of the lawnmower so that the engine remains activated when the lever is engaged, and the engine is shut off when the lever is disengaged.If the engine is not responding to the lever control in any of its settings, it is likely that the lever control has suffered damage and should be replaced. If the lever control, upon a visual inspection, seems to be punctured, torn, scraped, eroded, or damaged in some other way as a result of general wear and tear over long-term usage or from a direct impact with a hard object, the lever control should be removed and replaced with this genuine OEM replacement part before using the lawnmower again. Remember to wear work gloves as a safety precaution while repairing or replacing parts within an outdoor appliance. This is an OEM part sourced directly from the manufacturer. It is sold individually. This lever control is compatible with the following outdoor appliance brands: Husqvarna and Craftsman.

Fix fuel leaks or engine flooding on your riding mower with this fuel check valve. Controls fuel flow between tank and carburetor. Easy DIY repair.

Replacement bar adjustment kit for chainsaws. Includes adjustment bolt, retainer ring, and pin. Installs inside clutch cover to maintain proper chain tension. Replace if broken, worn, or missing.

Fix chain oil leaks and inadequate bar lubrication with this chainsaw oil pump kit. Ensures proper oil flow to bar and chain during operation.

Replacement fuel tank cap assembly for gas blowers and trimmers. Includes retainer connection. Replace if your cap is cracked, won't seal properly, or missing.