Craftsman Lawn Mower Parts

Snow blower not throwing snow far enough? Worn rubber auger paddles reduce clearing performance. This paddle restores throwing distance and efficiency.

This is a simple extension spring with an outside diameter of 0.38 and a slack length of 2.5. It is primarily used as an extension spring for snowblowers, but may be compatible with other lawn equipment. It’s designed to apply tension as the throttle is applied. The more gas there is, the more resistance will be present. Under most circumstances, replacement is easy. When the spring breaks or gets rusty, look at both points of attachment. Memorize where it’s attached, or take a picture, and remove the old spring using a pair of pliers if necessary. Install the new spring and the tool is ready to use. This is an OEM part sourced directly from MTD, and it is sold individually. It’s black in color and was initially designed for Troy-Bilt lawnmowers. However, because this is a versatile part, it has since been repurposed for a number of MTD and related machines in other brands. These include lawn tractors and snowblowers, as well as lawnmowers, in brands such as Ryobi, Yard Machines, Husky, and Cub Cadet.

Extension spring for lawn tractors and riding mowers. Replaces broken, damaged, or missing springs in pulley and belt assemblies. Direct fit part.

Flange bearing for snow thrower auger and drive systems. Replace if you notice unusual noise, vibration, or difficulty operating. Verify fit with your model.

Flange bearing for lawn tractors and walk-behind mowers. Replace if you notice excessive noise, vibration, or wheel wobble. Verify fit with your model number.

This is a bushing made from black plastic with a cleft down the middle to provide enough flex for easy insertion. It has a flanged design, which means it won’t easily pop out after installation, even under stress from constant vibration. The bushing’s primary purpose is to protect wires and cables from damage as they pass through a channel. As such, the material is fairly durable and does not need to be replaced under ordinary circumstances. That said, there are some situations in which it can become damaged. For one thing, it’s easy to damage while repairing the wires or cables that run through the bushing. If the bushing does need to be replaced, it requires disconnecting any cables or wires that run through the bushing. Pop out the old bushing with a rubber mallet, install the new bushing the same way, reconnect the wires, and the repair is complete. This is an OEM part sourced directly from MTD, and it is sold individually. It was initially used on snowblowers but has also been used on lawnmowers and lawn tractors.

This flange bearing fits tightly between two connected components to create an airtight seal in a variety of types of lawn and garden equipment. With time and use of the equipment, the flange bearing can start to become damaged, break, or may be lost. When this occurs, the flange bearing will need to be replaced.Place the equipment on a flat surface and disconnect the spark plug wire. The location of the flange bearing will vary based on the equipment being used, so condult the user manual. Disassemble the tool as needed to get access to the flange bearing. It can be removed using a set of pliers. Clean off the components where the bearing was located before installing the new flange bearing. Replace the components and connect the spark plug wire.This is a genuine OEM replacement part that is sourced directly from the manufacturer. The part is sold as an individual item. The flange bearing can be used with lawnmowers, edgers, and snowblowers manufactured by MasterCut, Craftsman, Yard-Man, Cub Cadet, Montgomery Wards, Yard Machines, and MTD.

A ball bearing is a rolling element bearing that uses balls to maintain the separation between the bearing races. This part is designed for use with outdoor lawn and garden power equipment such as snowblowers, chippers, shredders, and tillers. It is compatible with products by brands such as Craftsman, Cub Cadet, Ryobi, Troy-Bilt, Yard Machines, MTD, Huskee, Montgomery Wards, Bolens, Yard-Man, and MasterCut.The ball bearing part is crucial because its purpose is to reduce rotational friction while supporting radial and axial loads. Without functioning ball bearings, valuable outdoor equipment would fall apart and quickly stop working. That is why it is important to get any ball bearings replaced if they are worn out or malfunctioning.This ball bearing is made out of metal. The ball bearing is an original OEM part sourced directly from the manufacturer, MTD. It is sold individually.

Flange bearing for snowblowers and riding mowers. Replace if you notice noise, vibration, or resistance during operation. Verify fit with your model.

Flange bearing for lawn tractors and mowers. Replace if you notice wobbling, excessive noise, or difficulty engaging blades. Verify fit with your model.

17.90-inch high-lift mower blade for lawn tractors and riding mowers. Replace worn, bent, or dull blades to restore cut quality and deck performance.

Replacement blade for chipper shredders. Chops limbs and sticks into particles. Order a new blade if yours is dull, chipped, bent, or worn from use.

Replacement 22-inch cutting blade for walk-behind mowers. Restores cutting performance when blade is dull, bent, cracked, or damaged from impacts.

19-inch mulching blade for walk-behind lawn mowers. Replace your damaged, bent, or dull blade to restore cutting performance and mulching effectiveness.

Drive clutch cable that engages the drive belt to turn snowblower wheels. Replace if cable is frayed, stretched, or won't engage properly.

Replace your worn or broken walk-behind mower control cable. This cable connects the control handle to the engine or drive system and may need replacement if damaged or frayed.