Craftsman Pruner Parts

Fuel pickup filter draws gas from tank to carburetor. Replace if engine won't start or runs poorly due to clogged filter. Verify fit with your model number.

Hex screw fastener for securing lawn mower components. Replace if stripped, rusted, or missing to ensure proper assembly and equipment stability.

Ignition module for gas leaf blowers and trimmers. Works with flywheel to create spark timing. Replace if damaged by heat exposure or engine won't spark.

If your chainsaw rope won't retract after pulling, the starter spring likely needs replacement. This spring creates the recoil to start the engine.

Engine piston kit for gas trimmers and outdoor equipment. Replaces worn, damaged, or corroded pistons that cause poor compression and engine performance.

This carburetor mixes air and fuel for your gas trimmer's engine. Replace yours if it's clogged, damaged, or leaking to restore proper fuel delivery.

There are multiple uses for the 5/16-18 Hex Screw. It is often used with small gasoline-powered yard equipment such as lawn and garden machines. While hex screws such as these may be used in edgers and snowblowers, the most frequent use this screw is in yard tractors. This variety of screw is commonly used in attaching the various appendages of gas-powered equipment to a central operating platform. In particular, these hex screws are used to secure the engine block of power tools to the frame or housing of the equipment. Once in place, these fasteners have an almost unbreakable strength to them. This is so much so the case that often, in order to detach the engine manifold and repair the inner workings of an engine, the bolts must be chiseled or cut loose. In such cases, it is necessary for the bolts to be replaced during reassembly. Manufacturers insist that genuine OEM replacement parts be used in the rebuilding process. These replacement parts were manufactured to the same exacting specifications used to make the original screws. These OEM screws are compatible with equipment made and sold by Yard-Man, Cub Cadet, Troy-Bilt, Husky, MTD, Bolens, and Yard Machines.

This OEM sprocket assembly contains a sprocket, which is a circular gear with teeth that engage with the links on a chain to move the chain forward.A new sprocket assembly will be needed if the part is broken in any way or if the sprocket teeth are worn off. If it's not immediately obvious to the eye, a test can be performed to determine if a new sprocket assembly is needed. Simply move the chain and if at any point the chain becomes stuck, this means a new sprocket assembly is needed. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment machines.This is a genuine MTD part sourced directly from the manufacturer and is sold individually. The sprocket assembly is compatible with trimmers manufactured by either Troy-Bilt or Cub Cadet.

Starter won't pull freely or rope doesn't retract? This recoil starter spring retracts the pull cord and activates your engine. Simple DIY repair in minutes.

Genuine engine cylinder for gas line trimmers and outdoor power equipment. Houses the spark plug and piston to create the combustion chamber. Replace if cracked or worn.

Piston ring seals the space between piston and cylinder wall in gas-powered outdoor power equipment engines. Replace if worn, cracked, or causing smoke.

Engine won't engage when pulling starter rope? The starter pawl bridge connects the flywheel to spin your trimmer's engine. Easy DIY repair.

Secures the fuel tank to the body of your leaf blower or trimmer. Replace if screw is missing, stripped, or damaged to keep fuel tank properly mounted.

This screw is designed to be used with a range of handheld land and garden tools. The screw is a common piece of hardware used to fasten various parts of equipment and machines. Screws can be used for a range of applications depending on the equipment.Screws are meant to last, but they can wear down over time. The threads of the screws may become damaged or worn away. The screw could break or become corroded. When working on the machines, it is also possible for the screws to become lost. Having extra on hand can be a good idea. Replacing the screw is a simple project.This screw is intended for use with blowers, edgers, gas trimmers, and other trimmers. It is compatible with models from a variety of brands including Poulan, Husqvarna, Weed Eater, and Jonsered. Each screw is sold individually. This is a genuine OEM replacement screw that has been sourced from the manufacturer.

Ignition module for gas leaf blowers and line trimmers. Mounts near the flywheel to generate spark. Replace if cracked, corroded, or failing to start.

Can't start your leaf blower or trimmer? A broken starter handle prevents the pull cord from engaging the engine. This replacement handle restores easy starting in minutes.