Craftsman Snow Removal Equipment Fastener

This lock washer is used frequently for a number of applications on power yard equipment. The size, 5/16, is the default for many small engine housing and manifold applications. Lock washers are used with machined bolts to fasten engine blocks to the housing of the equipment being used. The compressed washer is able to handle the constant vibration of the small gasoline engine without losing the seal between the screw or bolt and the housing. Typically these lock washers only need to be replaced when they are misplaced during repairs or when the screws that attach them have to be chiseled or cut away, meaning the washers are destroyed as well. These OEM certified replacement washers have been manufactured to the same specifications as the originals they are replacing. In addition to lawn mowers, lock washers of this type and size are frequently used on blowers, lawn tractors, cultivators, snowblowers, and trimmers. Brands compatible with this type of washer are Murray, Husky, Poulan, Bolens, Yard-Man, Cub Cadet, Troy-Bilt, Yard Machines, MTD, and Ryobi.

This carriage bolt is a fastener with a flat tip and a round head with threading along the shank. Also known as coach bolts and plow bolts, the item can be used with many types of lawn and garden equipment. This is a 5/16 carriage bolt that resists turning after the bolt has been tightened. Wear and tear or impact can cause damage to a carriage bolt and lead to the need to replace them.Removing a carriage bolt requires twisting the nut loose from the end of the bolt and then hitting the nut with a hammer. This will begin to move the shoulder out of the lawn equipment. Continue the process until the bolt is loose enough to remove. Installing a new carriage bolt simply requires sliding the bolt into the hole, adding the nut, and tightening things up.This carriage bolt is designed for use with Craftsman, MasterCut, Toro, Yard-Man, Cub Cadet, Montgomery Wards, Ryobi, Huskee, Troy-Bilt, MTD, and Yard Machines lawn and garden equipment. It can be used with lawnmowers, chainsaws, snowblowers, edgers, and tillers. This is a genuine OEM product sourced directly from the manufacturer as an individual component.

The shoulder screw is used in places where a spacer or bearing surface is needed, since the top half of the screw is unthreaded. These fasteners are often used for guides, pivot points, mounting pins, axles, and even a shaft for bearings and bushings in various MTD engines. With regular use, the screws can wear down or be lost. Always repair the missing hardware promptly with genuine OEM replacements. Disengage the spark plug and wear gloves when performing work on engines for safety. This genuine OEM replacement shoulder screw has been designed to be compatible with machines from MTD, Troy-Bilt, Yard-Man, Yard Machines, Bolens, Cub Cadet, and Craftsman. It can be used for multiple applications and in multiple locations in different models of lawnmowers, tractors, and chippers that use the screw in various applications. Check your parts diagrams for the exact location and use of these screws before ordering. This is sold as an individual unit; order multiple quantities as needed.

This hex nut is designed for use with select trimmers and mowers. It is a standard hardware part that may have multiple applications depending on the type of unit and model. The nut is typically used to secure engine components or housing elements to provide safe use of the machine. These nuts are durable, but they are small and can become lost during other repairs. The constant exposure to vibrations and use can also cause them to strip or become damaged over time. Either way, a replacement with this genuine hex nut will resolve the issue and get equipment back in working order. This genuine OEM hex nut is manufactured to exact standards and sourced from the manufacturer. It can be used with trimmers and mowers from RYOBI, MTD, Bolens, Troy-Bilt, Yard Machines, Huskee, Yard Man, and Cub Cadet. Check the parts diagram for exact application and location of this nut and note that it may have multiple uses on select models. This hex nut is sold individually, and additional nuts will require the purchase of multiple pieces. In order to replace this nut, a hex socket wrench and driver will be required. Always wear gloves for safety.

This flat washer is used to attach the idler pulley in a number of small and medium sized gasoline powered engines. These engines include snow blowers, log splitters, riding mowers, lawn tractors, and chippers. Because the idler pulley is subject to a great deal of resistance when the pulley is engaged, eventually the pulley will wear out. Should there be a squealing sound when engaging the drive, the problem is likely the idler pulley. In these cases, the pulley must be replaced. It is a good idea to replace the surrounding hardware when replacing the idler pulley; tNhis includes the flat washer, which is subject to corrosion during heavy use. To replace the idler pulley, first detach the spark plug cap. If on a mower or tractor, drop the mower deck. Remove the original pulley and install in order: replacement pulley, hex bolt, flat washer, flange nut. Apart from dropping the mower deck, the only tools required to complete this installation may be a 9/16 ratchet and combination wrench. This washer is a genuine OEM replacement part, designed to perfectly replicate the original piece. This washer is compatible with Troy-Bilt, Yard Man, Yard Machines, MTD, and Craftsman devices.

Few parts fulfill as many roles on lawn mowers and other landscaping power tools than the cover screw. This screw serves to attach metal housing parts, assemblies, and shrouds to one another on equipment such as power vacuums, snow blowers, edgers, tillers, hedge trimmers, lawn tractors, leaf blowers, grass trimmers and cultivators. As these are extremely durable metal screws, they seldom fail under ordinary use. It should be noted, however, that they are most often used at connection and pressure points. Stresses at these junctions sometime loosen screws, causing them to be lost or occasionally resulting in stripped threads. It's also occasionally the case that these screws are lost during repair or routine maintenance of yard equipment because of their small size. Users should make sure to consult their owner's manuals for replacement steps and any special instructions. Because of their small size and the ease of losing them during repair work or maintenance, it's recommended to keep a supply of appropriately sized screws on hand. Most importantly, when replacing a part make sure to use a genuine OEM replacement part. They are manufactured according to the specs of the original parts and are perfect replicas.

The replacement handle bolt here can be used for lawn and garden equipment. The handle bolt is used with the handle knob to help secure the upper and lower handles of the machine together. If the bolt is damaged or missing, it will not be possible to secure the handles properly. The handle bolts are durable and made from metal, but they could become damaged due to corrosion or natural wear. In other cases, they could become lost. In either case, they will need to be replaced. The replacement is simple and will not require any tools, as the square part of the bolt will fit into the handle perfectly. The handle knob will then be used to keep it in place. The handle bolt is a genuine OEM Part for lawn mowers and snowblowers. It is compatible with some models from Husqvarna, Murray, Weed Eater, Poulan, Jonsered, Craftsman, and Ryobi. It should be noted that this product is sold individually, and the handle knob is not included.

This is a dual cable fitting, designed to work with snowblowers. The cable fitting holds the auger cable in place, ensuring that it does not become a safety issue. The cable simply runs through the fitting, and the part holds it in place. Cable fittings are made from durable plastic and are not moving parts. However, they can suffer damage in several different ways. Plastic becomes brittle over time and through exposure to the elements, and the fitting may eventually crack and break. It is also possible to damage the fitting through contact with a hard surface while using the snowblower. Replacing a dual cable fitting is not difficult, although it will require a socket set. Locate the fitting on the handle of the snowblower and remove the mounting bolt(s). Remove the fitting and replace it with the new one. Be careful that the cables are properly routed inside the new fitting, then replace the mounting bolt(s). This is a genuine OEM part, and it is sold individually. This dual cable fitting is compatible with Craftsman, MTD, and Yard Machine snow blowers.

This spacer is a genuine MTD part that can be used as a replacement part for several different kinds of small engines, including lawn mowers, snowblowers, and wood-chippers. A spacer's function is to serve as a means to lengthen the distance between parts by fitting over a bolt or a screw to secure and maintain that distance. A reason to replace a spacer might be simply losing or misplacing the spacer itself, as it is small and can easily fall through cracks or unscrew itself over long periods of time. Other reasons include the gradual rusting, deterioration, bending, or cracking materials that can be attributed to general overuse or long-term exposure. If a spacer is subject to any of this kind of damage, it is best to replace it before using an appliance that requires a functioning spacer, as the malfunctioning spacer might cause permanent or serious damage. Always wear gloves when handling, repairing, and operating outdoor equipment. This spacer part is compatible with the brands MTD, Troy-Bilt, Yard Machines, and Yard-Man. This part is sold individually.

This screw is designed to be used with a range of handheld land and garden tools. The screw is a common piece of hardware used to fasten various parts of equipment and machines. Screws can be used for a range of applications depending on the equipment.Screws are meant to last, but they can wear down over time. The threads of the screws may become damaged or worn away. The screw could break or become corroded. When working on the machines, it is also possible for the screws to become lost. Having extra on hand can be a good idea. Replacing the screw is a simple project.This screw is intended for use with blowers, edgers, gas trimmers, and other trimmers. It is compatible with models from a variety of brands including Poulan, Husqvarna, Weed Eater, and Jonsered. Each screw is sold individually. This is a genuine OEM replacement screw that has been sourced from the manufacturer.

This washer is a genuine Husqvarna part manufactured for use with lawnmowers. It is also compatible with lawn tractors, garden tractors, riding tractors, and other similar equipment. It is a hardened flat washer that is rather large compared to other washers. This washer is often used to attach the mower deck to the mower itself. Removing it is often part of a larger repair, and a screwdriver or socket wrench may be required to make this replacement. It is not unusual for washers and other hardware to experience wear and tear, especially if the mower gets heavy use. It may also need to be replaced if it becomes damaged while making other repairs.This washer is a genuine OEM part sourced directly from the manufacturer. It is sold individually, so be sure to check how many are needed and order accordingly. It is compatible with equipment manufactured by Ariens, Craftsman, Dixon, Husqvarna, Murray, and Craftsman.

This self-tapping screw is used to attach various parts to the engine housing of medium sized gasoline powered engines, in particular yard tools such as tillers, snow blowers, yard tractors, riding mowers, power vacuums, shredders, and chippers. It is used in over 150 different gasoline powered engines. Screws such as these are used particularly when a device is going to receive a great amount of vibration and stress while the engine is running and rotating tools are engaged. Such devices sustain a great deal of wear over time and the parts subject to replacement will eventually fail and need to be replaced. In such cases, it is wisest to replace the attaching hardware such as housing screws as well, because it is a self-tapping screw. Screws of this type are designed to forge a tight bond between the metal pieces they are securing together, but once loosened, they should ideally be replaced with new hardware. Make sure when replacing these screws to use genuine OEM parts like these screws. These replacement parts are manufactured to be identical to the original pieces. This hex screw is compatible with the following brands: MasterCut, Yard-Man, Yard Machine, Montgomery Wards, MTC, Murray, Bolens, Craftsman, Turf King, Troy Bilt, Cub Cadet, Huskee, Toro, and Ryobi.

This replacement screw is useful for many different types of handheld outdoor equipment. Screws are used as a means to hold parts of the machine together. The screws also help to reduce the amount of vibration that occurs in the machine.These screws are used in outdoor equipment, so there is a chance they could corrode over time. In some cases, the screws may also lose their thread, or the heads of the screws could start to become worn down. Owners who notice issues with the screws, or who notice a missing screw should replace them to ensure the proper function of the machine. Failure to replace damaged screws could result in more difficulty replacing them after they wear down further.The screw works on various types of equipment including blowers and trimmers. It is compatible with a range of brands including Murray, Craftsman, Yard Machines, Bolens, Yard-Man, Craftsman, Ryobi, and McCulloch. This is a genuine OEM part sourced from the manufacturer, and it is sold individually.