Crosley Agitator Parts

This washplate restores the washer's wash action. It mounts to the drive hub and rotates to move water and fabrics, helping resolve slipping, no-agitation, and poor cleaning when the original plate is worn, stripped, or cracked.

• Engages the drive hub to create the low-profile agitation that moves clothes and water
• Replaces a stripped, cracked, or rounded washplate that slips on the hub
• Common symptoms include clothes not moving, poor cleaning results, clicking/grinding during wash, or an impeller that spins freely by hand
• Also referred to as a low-profile agitator or impeller

• Disconnect power and turn off water before servicing
• Lift the lid, remove the center cap, then remove the center bolt to lift off the old washplate
• Clean and inspect hub/splines; align and fully seat the new washplate before reinstalling the bolt and cap
• Run a test cycle to ensure proper agitation and operation

This upper agitator—also called the clothes mover—is the top section of the agitator in select top-load washers. It works with the agitator cam and dogs to roll laundry over during wash strokes. Replace if cracked, stripped, or no longer engaging. What it does:

• Provides the upper vanes that lift and roll clothes for proper turnover during agitation
• Transfers one-way motion from the cam/dogs to the top section of the agitator
• Helps address symptoms like the top section free-spinning, poor turnover/cleaning, rattling/loose feel, or visible cracks/broken fins

• 1 upper agitator (clothes mover)

• Unplug the washer and turn off water before servicing
• Remove the dispenser and cap to access the center fastener; lift out the agitator assembly
• Separate the old upper section from the cam, seat the new clothes mover fully on the splines, and reassemble
• Hand-check for one-way engagement of the top section before running a test cycle

This agitator drive shaft sits inside the washer's gearcase and transfers motion to the agitator. Replacing a worn or stripped shaft restores firm engagement and reliable wash action while helping reduce slip and grinding during agitation.

• Transfers oscillating motion from the transmission to the agitator
• Provides the splined interface that engages the agitator/coupler
• Common symptoms include no agitation, intermittent/slipping agitation, or grinding/clicking from the gearcase
• Visible wear, rounded splines, or a bent shaft can lead to a loose or non-moving agitator

• Disconnect power and water; use proper PPE
• Requires removing the cabinet and gearcase; drain and reseal the gearcase per service procedures
• Keep gears, spacers, and clips in order; reassemble in the original orientation
• Inspect mating parts (agitator coupler/splines, drive block, seals) and replace if worn

This impeller cap fits over the dishwasher's wash pump impeller to secure it in place and help maintain proper water flow and spray pressure for effective cleaning. Replacing a cracked or missing cap can reduce noise and restore consistent performance.

• Secures the wash pump impeller and helps prevent wobble or rubbing
• Helps maintain proper water circulation to the spray arms
• Common symptoms of a failed/missing cap: poor cleaning, unusual grinding/rattling noises, or visible damage in the pump area
• Designed for the specific pump/sump design used on select models

• Disconnect power and turn off water supply before servicing
• Access the pump from inside the tub; remove the lower rack, spray arm, and filter/cover as required
• Note cap orientation; press or twist-lock fully onto the impeller (reuse any existing fastener if your model uses one)
• Inspect the impeller and seals while accessible; replace worn parts as needed

The Agitator Hub is an OEM part for Frigidaire washing machines. It connects the agitator to the drive shaft, enabling the agitator to rotate and move clothes effectively during the wash cycle.  

Causes of a bad agitator hub can include wear and tear from frequent use, exposure to harsh detergents or hard water, or damage from overloading the washer.  

Symptoms of a bad agitator hub include:

• Agitator not moving or rotating properly
• Loud noises or grinding sounds during the wash cycle
• Clothes not being cleaned effectively
• The washer shaking or vibrating excessively

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This agitator is a genuine Frigidaire part, sold individually. This agitator can be used as a replacement part for a washing machine or a washer/dryer combination appliance. This part rotates within the tub of the washing machine so that clothes and other items are tumbled around and fully cleaned.If an agitator has been subject to damage at some point in the standard lifespan of a washing machine, symptoms of damage will manifest in the form of a washing machine that will not agitate in a normal laundry cycle. If this is occurring, the agitator should be inspected for visible signs of damage, including punctures, scrapes, tears, and erosion to the material that could preclude it from serving its function. If the agitator seems damaged upon assessment, it should be removed and replaced with this genuine OEM replacement part before using the washing machine again.This is an OEM part sourced directly from the manufacturer. It is sold individually. This agitator is compatible with the following appliance brands: Frigidaire, Kenmore, Gibson, and Kelvinator.