Crosley Dishwasher Parts

Color: Black

This hold-down strap secures components in place to reduce movement and vibration, helping maintain stable operation and prolong part life. It's a simple replacement that restores proper fastening where the original strap has worn or failed. What it does:

• Secures and stabilizes assemblies to prevent shifting during operation
• Helps reduce vibration and noise caused by loose components
• Restores proper fastening after strap wear, cracking, or breakage
• Compatible with the original mounting points and fasteners used on the appliance

• One hold-down strap

• Disconnect power and water before beginning any repair
• Inspect mounting points and fasteners; replace any damaged hardware before installing the strap
• Use appropriate tools and follow OEM torque/fastening guidance where available

This small plastic retainer secures an appliance wire harness to the cabinet or internal components to prevent rubbing and strain on connections. Replacing a damaged clip helps keep wiring routed correctly and reduces the risk of intermittent electrical issues. What it does:

• Holds the wire harness in place to prevent chafing and contact with moving or hot parts
• Keeps connectors and wires from pulling loose during normal use
• Helps prevent intermittent power or control problems caused by loose wiring
• Reduces vibration noise from loose harnesses

• Disconnect power to the appliance before servicing to avoid shock or injury
• Inspect surrounding wiring and routing before removing the old clip
• The clip typically snaps into a mounting hole or channel; align harness and press until it seats
• Use common hand tools if needed; replace any damaged wiring or connectors found during installation

This dishwasher door spring provides the counterbalance tension that lets the door open and close smoothly. Replacing a worn or broken spring restores proper door feel and helps prevent the door from dropping unexpectedly.

• Provides counterbalance tension so the door opens and closes smoothly
• Helps the door stay partially open without drifting
• Reduces slamming or sudden drop when opening
• Common failure signs: door feels heavy, drops quickly, opens unevenly, or a spring is visibly broken

• Disconnect power and shut off water; remove the toe-kick/access panel
• Support the door; note spring routing and which frame holes are used before removal
• Install the new spring in the same holes; adjust hole selection only per service information to fine-tune tension
• Springs are under tension—wear gloves/eye protection; consider replacing both springs together for balanced operation

Color white. The wash arm measures about 11 inches, and the retainer about 3 inches.

This O-ring creates a watertight seal in your dishwasher's wash or drain system, helping prevent leaks and maintain proper water pressure. Replace a brittle, flattened, or damaged ring to restore a reliable, leak-free connection.

• Provides a watertight seal between mating parts such as pump housings, fittings, or hose joints
• Helps stop drips and seepage caused by a worn or deformed seal
• Common symptoms: water under the unit, moisture around pump/tubing connections, or leaks after reassembly
• Replace if the old ring is cracked, cut, flattened, or hardened

• Disconnect power and turn off the water supply before servicing
• Place a towel or shallow pan to catch residual water
• Clean the groove and mating surfaces; lightly moisten or use a manufacturer-approved lubricant to help the ring seat without pinching
• Seat evenly, reassemble without overtightening, and run a short test cycle to check for leaks

This rubber grommet cushions and secures appliance components where they pass through panels or mount to frames, reducing vibration and protecting wiring or hoses from abrasion. It helps restore quiet operation and stable mounting. What it does:

• Cushions mounts and reduces vibration or rattling from motors or panels
• Protects wires, hoses, and tubing from chafing where they pass through openings
• Keeps components properly positioned to prevent wear and noise
• Worn or missing grommets can cause rubbing, vibration noise, or movement of parts

• One rubber grommet as shown

• Disconnect power to the appliance before servicing
• Remove the damaged grommet and install the replacement in the same orientation
• No special tools typically required; small pliers or a flat tool can help seat tight grommets
• Inspect surrounding seals, wiring, and mounting hardware while replacing