Crosley Range Parts

 The Dual Element Surface Switch is an OEM part for Frigidaire electric ranges and cooktops. It governs power distribution to the dual element.

Causes may be loose electrical terminals within the switch, defects from past power surges, or general wear over extended use.

Symptoms of a bad surface switch include:

• Inability to toggle one or both elements independently
• Elements activating intermittently or staying stuck on
• Overheating, sparks or strange sounds from faulty connections
• Repeated burning or singeing of cookware bottoms

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This ice door spring restores the closing tension on the dispenser chute door. Replacing a fatigued spring helps the flap seal properly after dispensing, reducing warm-air leaks that cause frost buildup and ice clumping around the chute. What it does:

• Provides return tension so the ice chute door closes after dispensing
• Helps maintain a tight seal to limit frost, condensation, and air leaks
• Can resolve a chute door that sticks open/closed or won't fully close
• Reduce rattling or poor ice flow caused by a loose flapper

• 1 spring

• Disconnect power to the refrigerator before servicing
• Remove dispenser trim/control panel to access the ice door assembly
• Note spring orientation on the flapper; transfer/install carefully without over-bending
• Smooth flap movement and a proper seal before reassembly

• Dispenser door spring
• Flapper spring
• Ice chute door spring

This is the spark electrode used to ignite the gas in the oven. It creates a spark at the burner to light the flame so your oven can heat reliably.

• Generates the spark that lights the oven burner
• A failed electrode can cause no heat, delayed ignition, or the oven not lighting
• Intermittent sparking or clicking without ignition may indicate a worn or cracked tip
• Carbon buildup or damage to the ceramic insulator can prevent proper ignition

• Disconnect power and shut off gas before servicing
• Access the burner area, note wire routing, and handle the ceramic insulator carefully
• Position the electrode tip at the specified gap to the burner per service literature
• Test for proper spark and burner ignition after reassembly

This is the gas control valve for a surface burner. It regulates gas flow to the burner head so you can ignite the flame and adjust heat output safely and smoothly.

• Controls and meters gas to an individual cooktop/range burner
• Worn or leaking valves can cause hard-to-adjust flames, no flame, or gas odor
• A sticking or stripped valve stem can make the knob hard to turn or fail to shut off fully
• Helps restore precise flame control and reliable ignition

• Disconnect power and shut off the gas supply before servicing
• Allow the appliance to cool; work in a well-ventilated area
• Transfer any mounting hardware or orifice components from the old valve
• Check for leaks with an approved leak-detection method after reassembly and gas restoration

The Switch is an OEM part for Frigidaire ranges and ovens. It is responsible for controlling the temperature and operation of the warming drawer or zone feature.

Causes of a bad Switch can include electrical malfunctions or short circuits, mechanical wear from repeated use, and exposure to moisture or debris.

Symptoms of a bad Switch include:

• Inability to activate or control the warming drawer or zone
• Erratic temperature fluctuations
• Overheating or failure to heat the warming area

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Spacer is an OEM part for Frigidaire ranges and ovens. This part provides the necessary clearance between the oven door handle and the door itself, preventing friction and wear while ensuring the handle is securely attached and easy to use. This small but crucial component aids in the proper functioning of the oven door, making it easier and safer to open and close without exerting extra force.

Causes of a bad Spacer include mechanical stress leading to cracks or breaks, improper installation that may result in loosening over time, and degradation from heat exposure and frequent use.

Symptoms of a failing Spacer include:

• Loose oven door handle.
• Difficulty in opening or closing the oven door.
• Visible gaps or misalignment of the door handle.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This oven door hinge is a replacement for many models of ovens. Oven doors will have two hinges. If there is a problem with one or both of the hinges, it means that the door will not open and close properly. It might not stay closed, or it could be difficult to open. This would make it impossible to use the oven, and the hinge should be replaced as soon as possible.An oven door hinge could become damaged for a host of reasons. When the door is open, too much pressure could be placed on the hinge, which could cause it to break. It could become corroded over time, or the spring might wear down. When there are issues, the owner will want to replace the hinge to ensure the door stays closed. Owners should always make sure the oven is off and not powered before beginning work.The oven door hinge will work with certain models of ovens from Whirlpool, Maytag, Amana, Jenn-Air, Norge, Crosley, and Magic Chef. This is a genuine OEM replacement part, and it is sold individually. If both of the hinges need to be replaced, the owner will need to buy two.

This is a control knob that is used on ranges and stoves. The control knob is used to turn the burner on and adjust heat. Sometimes, the knobs can be damaged or come off and be lost. In some cases, the knob can also become loose on the base and hard to use.The process of replacing the control knob is simple and requires no tools. First, make sure the stove is turned off and is cool to the touch. Locate the knob that is broken or damaged and pull it away from its base. If it is stuck, a screwdriver can be used to pry it up. Place the new control knob on the base and press it in to secure it.This control knob is designed to be compatible with ovens, ranges, and stoves manufactured by Tappan, Frigidaire, and Crosley. It is sold as an individual item. This is a genuine OEM replacement part that is sourced directly from the manufacturer.

This pilot burner supplies the small, continuous flame that lights the surface burners on gas ranges/cooktops, helping ensure reliable burner ignition and steady performance.

• Provides a steady pilot flame to ignite the surface burners
• Helps restore lighting when surface burners won't ignite or the pilot won't stay lit
• Can address weak or inconsistent pilot flame at the top burners
• Typical signs include repeatedly having to relight the pilot or burners going out during use

• Disconnect electrical power and shut off gas before servicing
• Allow the appliance to cool and ventilate the work area
• Inspect and clean mating surfaces; replace brittle tubing or cracked fittings as needed
• After installation, check for leaks and adjust the pilot flame per the service manual

This 8-inch coil surface element restores reliable heating on the large burner of electric ranges and cooktops. Its 2350-watt design provides steady, even heat for boiling, frying, and everyday cooking.

• Converts electrical power into heat for the large cooktop position
• Common failure symptoms: no heat, uneven heating, only part of the coil glowing, visible breaks or blisters, or failed continuity
• Plug-in coil style for receptacle-type burner sockets
• If no heat persists after replacement, also inspect the element receptacle and the burner switch

• Disconnect power to the range/cooktop and allow the element to cool completely
• Lift the old element and pull straight out from the receptacle
• Align the new element's terminals with the receptacle, push in firmly until fully seated, and set it into the support/drip bowl
• Restore power and test the burner

Main Top - w/Black Glass

The Convection Fan Motor Kit is an OEM replacement part for Frigidaire ovens. This kit includes the motor responsible for driving the convection fan, which circulates hot air within the oven cavity to ensure even cooking and consistent temperatures during convection baking or roasting.

Over time, causes of a bad convection fan motor can include electrical wear, overheating due to heavy use, or damage from grease or debris buildup. Additionally, worn-out bearings in the motor can impair its performance.

Symptoms of a bad convection fan motor include:

• The fan not spinning or operating inconsistently  
• Uneven cooking results in convection mode  
• Strange noises such as rattling or grinding during operation  

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Note: Convection fan motor 5304467898 replaces earlier fan motors with a cooling blade. The fan motor doesn't include the cooling blade as it is no longer required.

This replacement oven door glass panel restores a clear, safe viewing surface when the window is cracked, shattered, or stained. It helps the door insulate properly and brings back a clean, finished appearance to your range or wall oven. What it does:

• Forms the glass viewing surface on the oven door
• Shields inner panes and insulation from spills and impact
• Aids in maintaining the door seal and stable cooking temperatures
• Typical symptoms: cracked or shattered glass, missing panel, sharp edges, or visible cosmetic damage

• One oven door glass panel

• Disconnect power and allow the appliance to cool completely before starting
• Remove the door and place it on a padded surface; keep track of screws and trim
• Transfer any brackets, nameplate, or trim pieces from the old glass as required by your model
• Wear cut-resistant gloves and handle glass carefully; tighten fasteners evenly without overtightening

Restore steady, even flames with this surface burner cap. It sits atop the burner head to shape the flame and shield the burner from spills and debris, helping keep lighting quick and cooking performance consistent.

• Shapes and centers the flame for efficient, even heating
• Protects the burner head from spills and food debris
• Helps proper ignition by maintaining the correct gap and alignment
• Typical symptoms: uneven or yellow flames, delayed ignition or constant clicking, visible chips/warping, or a missing cap

• Turn all controls off and allow the cooktop to cool completely
• Lift off the old cap; clean the burner head and igniter area
• Center the new cap on the burner head so it sits level and fully seated
• If ignition is delayed or the flame is uneven, re-seat and realign the cap

This is the factory handle set for select Frigidaire-built appliances. It restores a secure, comfortable grip and fresh appearance so doors or drawers open and close as intended. What it does

• Provides the handhold needed to open and close the appliance door or drawer
• Replaces cracked, broken, or missing handles
• Helps correct loose or wobbly handles that won't stay tight
• Refreshes worn or scuffed handles for a cleaner look

• Manufacturer-supplied handle set

• Disconnect power before servicing; allow hot surfaces to cool
• Remove interior/hidden mounting screws and the old handle
• Align and secure the new handle; re-use existing hardware/brackets if applicable
• Do not overtighten fasteners; verify smooth door/drawer operation

Color: black. It measures about 2 inches in diameter.