Parts for Whirlpool WFW9750WL02: 04 - Dispenser Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Fix a washer that won't fill, has an F20 error, or leaks water between loads. This water inlet valve controls flow during fill cycles. DIY repair.

Replacement water supply hose for your washer. Installs between components to restore proper flow. Needed when original hose is cracked, leaking, or brittle.

This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.

• Fastens a hose to a barb or port to prevent leaks
• Helps keep hoses from slipping off due to vibration or pressure
• Restores proper sealing when a clamp is rusted, bent, or stripped
• Common symptoms: water dripping at a hose joint, loose hose connection, or a clamp that won't tighten

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water when removing hoses
• Position the clamp just behind the hose barb/bead and secure with the appropriate tool
• Restore water and power, then run a quick check for leaks at the connection

The Water Inlet Flow Meter is an OEM part for Whirlpool washing machines. It is responsible for monitoring and regulating the flow of water entering the washing machine during the fill cycle, ensuring the correct amount of water is added for efficient and effective cleaning.

Causes of a faulty Water Inlet Flow Meter include sediment buildup, physical damage, or electrical issues with the meter's sensors or connections.  

Symptoms of a bad Water Inlet Flow Meter include:

• Incorrect water levels in the wash tub
• Washing machine not filling properly with water
• Error codes related to water inlet flow or water level issues

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Replacement drain hose for front-load and top-load washers. Connects the tub to the drain pump. Replace if cracked, kinked, leaking, or damaged.

This is the inlet nozzle that directs water into the washing machine tub during the fill cycle. It connects to the water inlet valve and channels water flow into the drum. Replace this nozzle if you notice restricted water flow, leaking at the tub entry point, or if the nozzle is cracked or clogged with mineral deposits.

This replacement lever is a small mechanical link that engages or releases its mating mechanism inside the appliance. Replacing a worn or broken lever restores crisp actuation and reliable operation of the related control or latch. What it does:

• Transfers motion from a button, handle, or cam to the connected mechanism (such as a latch, switch, or dispenser component)
• Ensures the mechanism moves fully and smoothly
• Wear or breakage can cause a loose feel, incomplete travel, or no response when pressing/pulling the control
• Visible cracks, missing tabs, binding, or intermittent operation are common signs it needs replacement

• 1 lever

• Disconnect power before servicing; also turn off water supply
• Access the assembly for your model per the service/parts diagram
• Note orientation of any springs or clips connected to the original lever; transfer them if present
• Reinstall with existing fasteners and test operation before reassembly

Fix a washer that stops mid-cycle or won't advance between wash stages. This actuator cam guides the lever arm movement for proper cycle transitions.

This plastic lever connects the dispenser mechanism in a washing machine, actuating the release of detergent or fabric softener at the correct point in the wash cycle. It transfers mechanical motion to open the dispenser at the proper time. Replace this lever if your washer is not dispensing detergent or fabric softener, or if the lever appears cracked or broken.

The Dispenser Actuator is an OEM part for Whirlpool washing machines. It is responsible for controlling the release of detergent and fabric softener during the wash cycle, ensuring that these cleaning agents are dispensed at the correct times.

Causes of a bad dispenser actuator can include wear and tear over time, damage from detergent residue build-up, or electrical faults within the actuator mechanism. If the actuator fails, it can disrupt the washing cycle and prevent proper dispensing of cleaning agents.

Symptoms of a bad dispenser actuator include:

• Detergent or fabric softener not being dispensed
• The washer displaying error codes related to the dispenser
• Intermittent or inconsistent dispensing
• Unusual noises during the dispensing phase

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement screw secures appliance components and panels so they stay aligned and rattle-free during operation. Replace stripped, missing, or corroded hardware to restore a tight fit and dependable performance. What it does

• Fastens brackets, panels, and internal sub-assemblies in the appliance
• Helps maintain alignment to reduce vibration and rattling
• Replaces missing, rusted, or stripped screws that no longer hold
• Useful when a part won't mount securely or a screw backs out during use

• One screw

• Disconnect power; for gas appliances, also shut off the gas supply
• Compare to the original for length and thread style for the location
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Do not overtighten; if the mounting hole or clip is worn, replace it

Washer not dispensing soap or softener? A clogged or broken distribution nozzle prevents water flow to dispensers. Moderate DIY repair restores function.

This drawer hook is the retainer that keeps an appliance drawer securely seated while still allowing easy release for cleaning or service. Replacing a worn or broken hook restores smooth, reliable drawer operation.

• Secures the drawer in its housing so it stays closed during use
• Acts as the catch/release point for removing the drawer when needed
• Helps maintain proper alignment for smooth opening and closing
• Common symptoms: drawer won't stay closed, pops open or falls out, won't latch, or the hook is visibly cracked/missing

• Disconnect power before servicing
• Fully open and remove the drawer to access the hook area
• Align the new hook with the slots/tabs and snap or seat it into place
• Avoid forcing components; refer to the service manual for model-specific steps

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Fix detergent not dispensing or musty odors with a new dispenser divider. This small part routes powder or liquid detergent properly. Easy DIY fix.

This is the lower cover panel for the detergent dispenser drawer on a front-load washing machine. It snaps onto the bottom of the dispenser drawer to enclose the compartment and direct water flow properly during the wash cycle. Replace this cover if it is cracked, missing, or warped, which can cause detergent to dispense incorrectly or water to leak from the dispenser area.

Secures the soap dispenser drawer inside your washer, keeping it aligned and stable. Replace if cracked, broken tabs, or drawer won't stay closed properly.

This rubber seal fits around the detergent or fabric softener dispenser housing on a front-load or top-load washing machine. It creates a watertight barrier that prevents water from leaking out of the dispenser area during wash and rinse cycles. Replace this seal if you notice water leaking from the dispenser, see visible cracks or deterioration in the rubber, or find detergent residue building up around the dispenser housing.

Connects detergent dispenser to wash tub for proper filling. Replace if cracked, leaking, or causing water pooling. Verify fit with your model number.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.