Parts for Kenmore 596.57087791 (59657087791, 596 57087791): Drain / Rollers / Evaporator Assembly Parts

This defrost thermostat helps control the refrigerator/freezer defrost cycle by sensing evaporator temperature and allowing the heater to run when frost removal is needed. Replaces a failed thermostat to restore normal defrost operation. What it does:

• Closes when the evaporator is cold so the defrost heater can run, then opens when the coil warms to stop defrosting
• Helps prevent excessive frost and ice buildup on the evaporator coil
• Common symptom: visible frost or ice on evaporator, excessive frost buildup, or defrost heater running constantly/ not at all
• Works with the defrost system to maintain efficient cooling performance

• One defrost thermostat

• Disconnect power to the appliance before starting any repair
• Mount on or near the evaporator coil as originally installed; secure wiring away from moving parts
• Inspect the harness and connector for damage; replace if corroded or brittle
• Test for continuity with a multimeter to confirm thermostat function before and after installation

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

Supports and enables smooth movement of your refrigerator cabinet. Replace if cracked, broken, or crumbled to restore stable positioning and mobility.

This small metal fastener secures the roller assembly to the refrigerator's bottom panel, allowing smooth door movement. Located underneath the appliance, it needs replacement if the refrigerator rocks, tilts, or has difficulty rolling when moved.

Refrigerator not cooling or freezer warm? A failed evaporator fan motor stops cold air circulation. DIY repair in under 30 minutes with basic tools.

Fixes frost buildup on evaporator coils and inconsistent cooling. This refrigerator defrost heater melts ice during defrost cycles. 20-minute repair.

Panel fastener screw for refrigerators and freezers. Secures cabinet panels, trim, and components. Replace if missing, stripped, or damaged.

This nylon washer is a small spacer that cushions fasteners and reduces metal-on-metal wear for smooth, quiet operation. It helps keep assemblies aligned and prevents premature wear where parts rotate or clamp together. What it does:

• Provides a low-friction bearing surface between mating parts to reduce wear and binding
• Cushions fasteners and helps maintain proper spacing and alignment
• Dampens vibration and reduces noise from rubbing metal components
• Can prevent loosening caused by direct metal-on-metal contact

• Inspect mating surfaces and replace any damaged fasteners or washers together for best results
• Ensure correct orientation and fit; do not force a washer that is too small or too large for the shaft or bolt
• Use basic hand tools; disconnect power to the appliance before working near electrical components

This part has been discontinued by the manufacturer and is no longer available.

Cam kit for refrigerator door hinges. Includes black and white cams that install at door bottom and hinge. Replace when cracked, broken, or worn.

Illuminates appliance interior. Replace when burned out or dimming. Verify wattage and base type match your model before ordering. Easy DIY fix.

This evaporator clip secures the evaporator assembly or its cover in the freezer compartment, helping maintain proper spacing and reduce vibration for steady cooling performance. Use it to replace a broken or missing mounting clip. What it does

• Holds the evaporator or evaporator cover in place to preserve correct airflow and clearance
• Reduces rattle and vibration caused by loose evaporator components
• Helps prevent improper frost build-up from a shifted evaporator
• Can resolve symptoms like unusual noise from the freezer or loose/unsupported evaporator hardware

• Disconnect power to the appliance before beginning any service.
• Access may require removing the evaporator cover or rear freezer panel—follow the OEM service instructions.
• Handle evaporator fins and tubing carefully to avoid damage during removal/installation.
• Replace only with the exact OEM-style clip.

Includes both shims as seen in the photo

Includes both shims as seen in the photo

This ice maker assembly produces and dispenses ice cubes in your refrigerator's freezer compartment. It automatically fills with water, freezes it into cubes, and releases them into the ice bin. Replace this part when your refrigerator stops making ice, produces misshapen cubes, or makes unusual noises during the ice-making cycle.