Electrolux Microwave Parts

This door latch hook secures the refrigerator door latch so the door closes and seals correctly. Replacing a broken or worn hook restores reliable door latching and helps prevent temperature loss from an improperly closed door. What it does:

• Secures the door latch assembly so the refrigerator door stays closed.
• Restores proper latch engagement to help maintain the door seal and consistent cooling when the door was not closing fully.
• Can address symptoms such as a door that won't latch, door popping open, or visible damage to the hook.
• Direct replacement for the factory latch hook to restore proper fit and function.

• Disconnect power to the appliance before starting any repair.
• Remove door trim or inner liner as needed to access the latch; keep all screws and fasteners for reassembly.
• Verify latch alignment and striker position before tightening; hand-tighten first and avoid over-tightening.

Right side tool part # AP3778556

This left-side door latch head is the hook assembly on the microwave door that engages the interlock switches. Replacing a worn latch restores a secure close and reliable start/stop so the unit operates only with the door fully shut. What it does:

• Hooks into the cabinet to keep the door closed and aligned
• Actuates the door interlock switches for safe operation
• Helps prevent doors from popping open or needing pressure to run

• Includes 1 left-side latch head

• Disconnect power at the breaker before servicing
• Remove the inner door trim to access the latch; support the door and protect the glass
• Compare orientation and transfer any reusable hardware from the original part
• After reassembly, verify the door closes smoothly and the microwave only starts with the door fully closed

Compressor start capacitor that helps the refrigerator compressor start reliably so the appliance can maintain proper cooling. Replace a weak or failed capacitor to reduce hard-starting, excessive humming, or loss of cooling. What it does:

• Provides the starting boost the compressor needs to reach running speed.
• Commonly linked to symptoms like compressor humming but not starting, warm refrigerator, or frequent on/off cycling.
• Works with the compressor start circuit; a failed capacitor can prevent the compressor from starting.
• Visible damage, leakage, or failed electrical tests indicate replacement is needed.

• Disconnect power to the appliance before accessing the capacitor.
• Discharge the capacitor before touching terminals to avoid shock.
• Note wire locations or photograph connections before removal; reconnect wires exactly.

This replacement motor restores reliable rotation to the component it drives, helping your appliance circulate air or operate as designed. Replacing a worn motor can resolve no-start conditions, loud operation, and weak performance.

• Provides the rotational drive for the attached component, enabling proper airflow or movement
• Common failure symptoms include humming without turning, intermittent operation, seized shaft, or grinding/squealing noises
• Visual signs like burned windings, cracked housing, or excessive shaft play also indicate replacement is needed

• Disconnect power to the appliance before servicing; allow any moving parts to stop completely
• Photograph or label wire positions and transfer them to the new motor one-for-one
• Reuse existing mounting hardware and verify the motor and attached wheel/blade spin freely without rubbing
• After installation, restore power and test operation before final reassembly

This replacement motor restores the rotation your appliance relies on to move air or drive a mechanism, bringing normal operation and performance back when the original motor has failed or become noisy. What it does:

• Converts electrical power into controlled shaft rotation to drive the associated component
• A failing motor may cause no movement, intermittent operation, or unusual humming/grinding noises
• Can contribute to reduced performance if the driven part doesn't run as intended
• May present with overheating smell or visible signs of wear on the old unit

• One motor

• Disconnect the appliance from power before servicing
• Note wire locations and connector orientation; transfer any brackets, grommets, or hardware from the old motor
• Handle sheet-metal edges carefully; wear cut-resistant gloves
• After installation, confirm the shaft spins freely by hand before restoring power and testing

The Latch is an OEM replacement part for Frigidaire built-in microwaves. Securely mounted to the top interior section of the microwave cavity door, the positive-locking latch holds the door safely shut during operation. Crafted from corrosion-resistant materials for extended use, the latch handle withdraws the hook mechanism with a simple pull to conveniently access food within.

Symptoms of a bad latch include:

• The microwave door popping or falling open unexpectedly  
• Difficulty closing or fully engaging the secure latch hook 
• Wear signs like loose mounting points or a worn handle

Causes can involve repeated opening/closing cycles gradually loosening mounting fixtures, or parts rendered ineffective by moisture intrusion over time.

Replacing this Frigidaire OEM latch prevents potential microwave door opening during cooking cycles. Compatible with Electrolux, Gibson, Kelvinator, and Kenmore built-in models.

This switch/fuse kit replaces a worn or failed control switch and associated fuse to restore reliable power control. It provides the exact components needed to address common start and power interruptions. What it does:

• Replaces a faulty control switch to restore on/off or cycle control
• Replaces the protective fuse to stop power loss from a blown fuse
• Helps resolve no-start, intermittent power, or control failures
• Restores proper electrical continuity for safe operation

• Disconnect power to the appliance before starting any work
• Handle electrical components carefully and avoid metal contact with terminals
• Verify correct part orientation and secure all connections per OEM guidance

A replacement tension spring used to restore normal movement and positioning for the affected appliance component. Replaces a worn or broken spring to help parts return to their intended position and reduce loose or uneven operation. What it does:

• Provides tension or counter-force for a door, drawer or linkage so the part moves smoothly and returns to position.
• Restores alignment and prevents sagging, slamming, or parts that don't stay in place.
• Reduces noise and uneven movement caused by a stretched or broken spring.
• Useful when a worn spring causes intermittent operation or poor component response.

• Disconnect power and water before servicing. Wear eye protection and gloves — springs can release suddenly.
• Inspect mounting points, clips and anchors; replace any damaged hardware to ensure proper function.
• Use appropriate tools (needle-nose pliers, spring hook) and follow OEM instructions for safe installation.

This is a genuine replacement cover designed to protect internal components and restore the appliance's finished appearance. It provides a durable barrier that helps prevent dust, moisture, and accidental contact with internal parts. What it does:

• Covers and protects internal components behind the panel, maintaining appliance safety and appearance
• Helps prevent debris and moisture from reaching sensitive parts
• Restores a secure fit and alignment of the front/cabinet area
• Useful when the original cover is cracked, warped, or missing

• One replacement cover

• Disconnect power (and water, if applicable) before starting any repair
• Follow OEM service instructions for removal and reinstallation to avoid damaging adjacent components
• Use appropriate hand tools; avoid overtightening fasteners

This motor start/run capacitor helps the compressor and fan motors start and run reliably, restoring normal cooling performance when a failing capacitor causes hard starts or intermittent motor operation. A direct-replacement component for affected units. What it does:

• Provides the electrical phase shift and stored energy needed for compressor and fan motor startup.
• Helps prevent slow starts, humming, or motors that won't start reliably.
• Restores stable motor operation and can reduce overheating or tripping caused by a weak capacitor.
• Works as a replacement for the same OEM-design capacitor in compatible refrigerators and freezers.

• One replacement capacitor (single unit)

• Disconnect power to the appliance before inspecting or replacing the capacitor to avoid shock.
• Verify capacitor is fully discharged before handling; use insulated tools and follow safety procedures.
• Match the capacitor's mounting and terminal type to the existing part for correct fit and connection.

Replacement screw used to secure panels, trim, and internal components in Frigidaire appliances. Restores proper fit after repairs and helps eliminate rattling or loose parts for safer, quieter operation. What it does:

• Secures panels, brackets, and trim to maintain correct alignment and fit
• Prevents vibration and rattling caused by loose or missing fasteners
• Use when original screw is missing, stripped, or damaged
• Matches common fastener locations on affected Frigidaire appliances

• Disconnect power and water before starting any repair
• Use the correct driver to avoid stripping the screw head; hand-start to ensure alignment
• Do not overtighten; tighten until snug to avoid damaging threads or plastic parts

This latch hook is the replacement hook that secures a door latch assembly so the appliance door stays closed and operates correctly. It restores proper door engagement to prevent intermittent opening during use. What it does:

• Replaces a worn or broken hook that keeps the door latch engaged
• Helps the door stay closed and maintain a tight seal during operation
• Stops intermittent or failed latching that can interrupt cycles or operation
• Works as part of the door/latch mechanism to ensure consistent engagement

• Disconnect power (and water supply for dishwashers) before starting any repair
• Inspect the latch assembly and strike for wear or damage before installing the new hook
• Test door operation and cycle the appliance to confirm proper engagement after installation

A replacement unified-thread screw used to secure appliance panels and internal components. Provides a direct fastener to restore secure attachment when original screws are missing, damaged, or corroded. What it does:

• Fastens panels, brackets, trim pieces, and other appliance components that use a unified-thread screw.
• Restores secure mounting to reduce rattling, movement, or misalignment of parts.
• Replaces stripped, rusted, or missing screws to help maintain safe operation.
• Works where the appliance's service manual or parts diagram specifies a unified-thread fastening point.

• Disconnect power and water before servicing for safety.
• Use the correct screwdriver or bit to avoid stripping the head; install by hand until started, then snug—do not overtighten.
• Replace like-for-like: match thread type and length to the removed screw to ensure proper fit and function.
• If other fasteners show corrosion or damage, inspect nearby hardware and replace as needed.

This is a replacement refrigerator water filter cartridge that helps reduce taste and odor from your drinking water and ice for cleaner, better-tasting results. Ideal for refrigerators that use an inline/cartridge-style filter. What it does:

• Filters chlorine taste and odor to improve water and ice flavor
• Helps reduce common particulates and sediments from the water flow
• Restores normal water dispensing performance when the original filter is exhausted
• Commonly replaced when water tastes off, ice smells, or water flow is reduced

• Replace with the refrigerator powered off or water supply shut off when possible
• Follow refrigerator manufacturer instructions for proper seating, alignment, and filter reset
• Flush several gallons of water through the dispenser after installation to clear air and loose carbon fines
• Dispose of the used cartridge according to local regulations