Electrolux Microwave Parts

This replacement power line cord restores safe electrical connection to the appliance so it powers up reliably. It replaces a damaged or worn cord to eliminate intermittent power, burning smells, or visible frays. What it does:

• Delivers mains power from the outlet to the appliance so controls and motors operate
• Replaces frayed, cut, burned or intermittently-working cords that cause power loss
• Stops arcing or burning smells caused by damaged insulation or connections
• Restores a secure connection when the original cord or strain relief is broken

• Disconnect appliance from power before inspecting or replacing the cord; follow all local electrical codes
• Route the cord through the original strain relief and secure it to prevent tugging on terminals
• Tighten terminal screws firmly and ensure wire colors match original terminal layout

This is a genuine mounting screw used to secure appliance components and panels for a safe, stable fit. It replaces a lost or damaged fastener to restore proper alignment and reduce rattles or loose trim. What it does:

• Secures panels, trim, brackets or small assemblies to the appliance frame
• Prevents vibration-related noise and loose or sagging parts
• Restores proper fit after repair or disassembly
• Useful when the original screw is stripped, missing, or broken

• One mounting screw

• Use the correct screwdriver or bit to avoid stripping the head
• Power off and unplug the appliance before servicing when applicable
• Keep removed hardware organized to ensure correct reassembly
• If threads are damaged, replace with the specified OEM screw only

Note: Quantity is one tool (right side) 

Left side tool is part # AP3778569

Control transformer that supplies the low-voltage power needed for the appliance's electronic control/console, restoring reliable operation when the original transformer fails or the display and controls lose power. What it does:

• Converts incoming line voltage to the low-voltage supply used by the control board and console.
• Keeps the display, touchpad/keys and control electronics powered and stable.
• Common symptoms of a failing transformer: unlit or blank display, unresponsive controls, intermittent operation, or control board power loss.
• Replace a visibly burned, cracked, or shorted transformer to prevent further electrical damage.

• Always disconnect power to the appliance before servicing to avoid electric shock.
• Take care with wiring: match original connector positions and secure all wire nuts/terminals.
• Inspect mounting hardware and insulation; replace any damaged fasteners or wires.

This thermal cut-out is a temperature-sensing safety device that helps protect the refrigerator's defrost/heater circuit by opening the circuit when temperatures exceed safe levels. It prevents overheating and helps maintain normal defrost cycles. What it does:

• Senses temperature in the defrost/heater area and opens the circuit to stop heating if temperatures get too high
• Prevents overheating of defrost heater or related components
• Can cause defrost failure symptoms when faulty, such as excessive frost buildup or poor cooling
• May also contribute to long run-times or irregular defrost cycles when not operating correctly

• Disconnect power to the appliance before servicing to avoid electrical shock
• Handle the part and wiring gently; ensure correct orientation and secure connections per service manual
• Use the exact replacement part number for compatibility

This replacement hook secures a cabinet or door component so it stays in position and restores normal closing and retention. It's a small but important part for keeping doors, covers, or bins from slipping. What it does:

• Acts as a mechanical retainer to hold a door, cover or bin in the proper position
• Prevents doors or compartments from falling open or shifting during use
• Restores secure engagement when the original hook is broken, bent, or missing
• Works with the existing mounting points and mating latch or catch

• One hook

• Disconnect power to the appliance before accessing internal components
• Remove any obstructing panels or shelves to reach the mounting area
• Replace the hook using the existing screw/clip fasteners; do not force or modify mounting points
• If other latch components are damaged, replace them as a set for reliable operation

This replacement cam is the small rotating actuator that engages and controls movement in compatible appliance mechanisms, restoring proper engagement and smooth operation where the original cam has worn or broken. What it does:

• Transfers rotational motion to a latch or linkage to enable proper opening, closing, or dispensing actions
• Ensures consistent engagement and timing of the associated mechanism
• Common symptoms it can fix: intermittent or failed latching, loose or sloppy movement, clicking or grinding noises during operation
• Small, precision part used where alignment and rotation are required

• Disconnect power to the appliance before servicing to avoid shock or injury
• Handle small parts carefully and keep track of fasteners and orientation for correct reassembly
• Installation may require removal of exterior panels or a control assembly; refer to the service manual or diagram for step-by-step guidance

This replacement frame restores the appliance's front cabinet trim for a finished look and secure component fit. It helps protect internal parts and keeps the control area or door edges properly aligned. What it does:

• Replaces damaged, cracked, or warped front trim that affects appearance or fit
• Secures adjacent panels and provides a mounting surface for controls or seals
• Helps stop drafts or gaps that can form around doors or control openings
• Restores proper alignment to reduce rubbing or interference with moving parts

• One replacement frame as pictured

• Disconnect power (unplug or switch off breaker) before starting any repair
• Basic hand tools (screwdriver, nut driver) are typically required; keep fasteners for reuse if intact
• Handle edges carefully to avoid scratching the finish; protect surrounding surfaces during installation