Electrolux Refrigerator Gasket & Seal

This seal-damper is the gasket that fits around a refrigerator's air damper to help keep compartments properly separated and maintain intended airflow. Replacing a torn or compressed seal helps reduce uneven cooling and drafts. What it does:

• Seals the air damper opening to limit unwanted air exchange between compartments
• Helps maintain stable temperatures by preventing cold or warm air leakage
• Common symptom fix: reduces uneven cooling or warm spots near the damper area
• Also helps reduce excess frost or condensation that can form from persistent air leaks

• Disconnect power to the appliance before starting any repair and remove nearby food/shelves for access
• Access the damper housing per your model's service instructions, remove the old seal, and seat the new seal onto the damper frame or mounting groove
• Clean the mounting surface of debris or old adhesive so the new seal sits flat; use gentle pressure to fully engage the seal
• If the damper housing is cracked or the seal does not seat properly, replace the damper assembly.

This refrigerator seal restores a tight barrier between internal components. Replacing a worn or damaged seal helps prevent air leaks and moisture intrusion, supporting proper airflow, stable temperatures, and reduced frost or condensation around the joint.

• Creates an air-tight barrier between mating surfaces
• Helps maintain correct airflow and temperature balance between compartments
• Reduces frost, condensation, and warm/cold spots near the sealed area
• Common signs of failure: visible gaps, loose/crumbled seal, rattling panel, moisture or frost at the joint

• Disconnect power before servicing
• Remove the related cover or housing to access the old seal
• Clean contact surfaces; install the new seal in the same orientation without stretching or pinching
• Reassemble and verify an even seal and normal airflow before returning to service

This H-shaped evaporator gasket creates a tight seal around the evaporator housing to help control airflow and reduce frost buildup in the freezer compartment. It replaces a worn or cracked gasket to restore proper cooling performance. What it does

• Seals the evaporator housing to prevent warm, moist air from entering the evaporator area.
• Helps maintain consistent airflow over the evaporator for efficient defrosting and cooling.
• Reduces frost and ice buildup caused by gaps or leaks around the evaporator.
• Commonly used when you see excessive frost, poor cooling, or visible gasket damage near the evaporator.

• One H-shaped evaporator gasket.

• Disconnect power to the appliance before starting any repair.
• Remove freezer panels and the evaporator cover to access the gasket; handle evaporator fins carefully to avoid damage.
• Clean mating surfaces and remove old adhesive or residue before installing the new gasket for a proper seal.
• If adhesive is required, use a refrigerator-safe sealant recommended by the manufacturer.

This coil cover seal is a molded gasket that fits around the evaporator/coil cover to help keep airflow directed and reduce moisture and frost buildup. It restores the cover's sealing surface for more consistent cooling performance. What it does:

• Seals the evaporator/coil cover to help maintain proper airflow through the coil
• Helps reduce frost or ice buildup by keeping moist air away from cold coil surfaces
• Can prevent water dripping or pooling inside the cabinet near the coil
• Restores a tighter seal after a cracked, torn, or compressed gasket reduces effectiveness

• Disconnect power to the appliance before starting any repair
• You may need to remove the evaporator/coil cover or access panel to reach the seal
• Clean the mating surfaces and dry thoroughly before installing the new seal
• Handle the gasket gently and press evenly to seat; avoid stretching or sharp tools that could damage the part

This replacement door seal creates a tight perimeter seal to help keep conditioned air inside and reduce moisture or frost buildup. Fits factory specifications to restore proper sealing and improve efficiency. What it does

• Forms an airtight barrier around the door to limit air exchange and energy loss
• Helps prevent frost, condensation, and water pooling inside or under the appliance
• Reduces strain on the compressor by maintaining correct internal temperature
• Common symptom fix for visible gaps, torn or flattened gasket, or excessive frost buildup

• Seal as shown

• Disconnect power or unplug the appliance before starting any service
• Clean the door frame thoroughly before installing to ensure a good seal
• Work the gasket into the channel evenly; avoid overstretching or twisting
• If clips or retainer strips are present, follow OEM guidance for proper seating

This replacement coil-cover gasket seals the refrigerator coil/cover area to help maintain proper airflow and reduce dust buildup around the condenser/evaporator cover. Restores the intended fit and helps maintain cooling efficiency. What it does:

• Seals the gap between the coil cover and cabinet to direct airflow over coils
• Helps prevent dust, debris and pet hair from collecting on coils
• Reduces vibration noise by cushioning the cover edge
• Commonly replaced when the gasket is torn, flattened, or missing, or when air leaks are noticed

• Inspect mating surfaces and remove old adhesive/residue before installing for a secure seal
• Use appropriate adhesive or clips if required by your model; follow OEM instructions
• Disconnect power to the appliance before servicing and avoid sharp edges on sheet metal

This air duct gasket seals the refrigerator's air duct to help direct cold airflow and reduce air leaks for more consistent temperatures. It replaces a worn or damaged duct seal to restore proper circulation and efficiency. What it does:

• Seals the connection between the air duct and cabinet to prevent cold air loss
• Helps maintain consistent fridge/freezer temperatures by directing airflow
• Reduces frost buildup and uneven cooling caused by gaps or leaks
• Commonly replaced when torn, compressed, or missing

• Designed for straightforward replacement; inspect surrounding duct for damage before installing
• Clean mating surfaces and remove old adhesive or residue for a proper seal
• Use appropriate hand tools; avoid sharp tools that could cut the gasket
• Disconnect power to the appliance if accessing electrical components nearby

The Freezer Door Gasket is an OEM replacement part for Frigidaire refrigerators. It creates a seal around the freezer door to maintain a consistent temperature by keeping cold air in and warm air out. This helps ensure proper freezing conditions and prevents energy loss.

Over time, gaskets can degrade due to wear, exposure to extreme temperatures, or cleaning with harsh chemicals. A damaged or worn gasket may fail to seal properly, affecting the freezer's efficiency and potentially leading to increased energy consumption.

Symptoms of a bad gasket include:

• Frost or ice buildup inside the freezer
• Difficulty keeping the freezer door fully closed
• Warm air entering the freezer, causing temperature fluctuations
• Increased energy bills due to inefficient operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This gray, magnetic freezer door gasket seals the perimeter of the door to keep cold air in and moisture out, helping maintain proper temperatures and reduce frost buildup for dependable food preservation.

• Forms an airtight magnetic seal between the freezer door and cabinet
• Helps stabilize internal temperature and humidity to limit frost and ice
• Common signs of failure: cracks or warping; condensation around the door; frost near the gasket; door not closing flush
• Restores sealing performance when the original gasket hardens or shrinks

• Unplug the refrigerator before servicing; use caution around sharp edges
• Warm the new gasket (warm water or low heat) to make it pliable
• Seat corners into the door retainer first, then work along the sides for an even fit
• Verify an even seal all around (dollar-bill test) and adjust gasket or door alignment as needed

This door gasket seals the refrigerator door to help maintain proper temperature and reduce energy loss. It replaces a worn, torn, or compressed seal to improve cooling performance and food safety. What it does:

• Creates an airtight seal between the door and cabinet to keep cold air in and warm air out
• Helps prevent frost build-up and reduces moisture inside the compartment
• Can stop visible gaps that allow warm air and odors to enter
• Restores consistent temperatures for better food preservation

• One refrigerator door gasket

• Handle gently to avoid stretching or tearing; follow the appliance manufacturer's alignment and fastening steps
• Clean the door flange and gasket channel before installation for a proper seal
• Some gaskets require heating (hair dryer) or a short break-in period to fully seat; follow your model's instructions

This replacement door gasket seals the refrigerator compartment to keep cold air in and warm air out, helping maintain consistent temperatures and reduce energy use. It fits along the cabinet opening and forms the primary seal between door and cabinet. What it does:

• Creates an airtight seal to help maintain internal cooling and reduce compressor runtime
• Prevents warm, moist air from entering and causing frost build-up or condensation
• Helps keep food fresher by maintaining stable temperatures
• Common symptom: visible cracks, gaps, or torn edges around the door perimeter
• Common symptom: warm spots inside the fridge, excessive frost, or higher energy use

• Unplug or disconnect power to the appliance before starting any repair
• Remove the old gasket and clean the sealing surface thoroughly before installing the new gasket
• Some installations require basic hand tools; check the appliance's service guide for detailed steps
• If adhesive or clips are used, follow OEM instructions