Electrolux Wall Oven Control Board

This electronic oven control board governs your range's heating functions and displays the time and timer. Replacing a failed board restores reliable bake/broil operation, accurate temperature control, and a responsive clock/timer interface. What it does:

• Controls bake/broil circuits to run selected cooking modes
• Monitors the oven temperature sensor and regulates heat to the set temperature
• Drives the time-of-day and countdown timer display
• Interprets keypad inputs for mode selection and settings
• Failure symptoms can include no heat or erratic heat, a blank or flickering display, or unresponsive buttons

• One electronic control board assembly

• Disconnect power at the breaker before servicing; verify no voltage is present
• Use anti-static precautions and handle the board by its edges
• Photograph wiring and transfer connectors one at a time to the same positions
• Reuse the existing mounting hardware and any faceplate/overlay as required; set the clock after restoring power

This electronic control board regulates the refrigerator's functions and user interface, restoring reliable operation when the original board fails. Replacing a faulty board can stop erratic behavior and restore normal temperature and display control. What it does:

• Manages compressor, fan, defrost and other timed cycles to maintain proper cooling
• Processes user inputs and controls the display/LEDs
• Can stop erratic cycling, unresponsive controls, or incorrect temperature behavior
• Helps resume normal operation when the original board is damaged by power surges or component failure

• Disconnect power to the appliance before starting any work
• Handle the board by the edges and avoid static discharge; use an anti-static wrist strap if available
• Confirm connectors match and seat fully; do not force plugs

This is a replacement refrigerator water filter cartridge that helps reduce taste and odor from your drinking water and ice for cleaner, better-tasting results. Ideal for refrigerators that use an inline/cartridge-style filter. What it does:

• Filters chlorine taste and odor to improve water and ice flavor
• Helps reduce common particulates and sediments from the water flow
• Restores normal water dispensing performance when the original filter is exhausted
• Commonly replaced when water tastes off, ice smells, or water flow is reduced

• Replace with the refrigerator powered off or water supply shut off when possible
• Follow refrigerator manufacturer instructions for proper seating, alignment, and filter reset
• Flush several gallons of water through the dispenser after installation to clear air and loose carbon fines
• Dispose of the used cartridge according to local regulations

This electronic control board regulates the appliance's functions and user interface so cycles and settings respond correctly. Replacing a faulty board restores reliable control and display operation when the original board has failed. What it does:

• Interprets user commands and sends signals to motors, valves, and other components
• Controls cycle timing, temperature, and other programmed functions
• Can cause loss of display, non-responsive buttons, or failure to start when defective
• May trigger erratic or unexpected operation if internal electronics fail

• One electronic control board as shown

• Disconnect power (unplug or switch off breaker) before beginning work
• Handle the board by its edges and avoid static discharge (use an anti-static wrist strap if available)
• Verify appliance model and part number match before installing

This electronic control board replaces the oven's primary control module to restore timing, display, and bake/broil cycle control. It fixes issues where the range won't start, displays errors, or has unresponsive touch controls. What it does:

• Manages oven temperature settings, timed bake cycles, and user interface commands
• Controls relays and sends signals to heating elements and sensors
• Helps stop incorrect displays, unresponsive buttons, or intermittent operation
• Works with safety interlocks and diagnostics to maintain normal oven functions

• One electronic control board as shown

• Disconnect power at the breaker before accessing the control panel to avoid shock
• Handle the board by edges and avoid touching components to prevent ESD damage
• Confirm connector locations match before installing; secure mounting screws and connectors

This listing is for a Frigidaire oven control board. The oven control board works in conjunction with the control board assembly and receives information regarding setting and oven temperature. Essentially the control board is the most important component in regards to the oven's function. The only way to properly ensure a control board has gone bad is through testing with a voltage meter. However, initial signs such as certain burners not working or the broil or baking functions failing can also be indicators. On this model, the board contains a faceplate that shows the time, which means the timer will also go out. On this model, the control board is housed in a protective casing behind the control assembly on a wall oven. Slide the oven from the wall and remove the anchoring screws located around the perimeter of the oven. The control assembly can be removed, exposing the protective casing. Remove the small screws that fasten the casing. Unplug the control board from the wire harness and begin the installation of the new component. This part is made exclusively for Electrolux appliances. The product is sourced directly from the manufacturer as a genuine OEM product.

Main electronic control board that manages the appliance's timing, temperature and cycle functions, restoring responsive controls and consistent operation when the original board fails or behaves erratically. What it does:

• Regulates key functions and signals between user controls, sensors, and motors to run cycles correctly.
• Controls timing and sequences for compressors, fans, defrost/heater circuits and other automatic functions.
• Replaces a failed board that causes unresponsive buttons, blank or error displays, or erratic cycling.
• Can resolve intermittent operation and failures tied to electronic control faults (diagnose before replacing).

• Disconnect power to the appliance before starting any service to avoid electric shock.
• Handle the board carefully and avoid static discharge; use ESD precautions if possible.
• Installation typically requires removal of the control panel and careful reconnection of wire harnesses; keep track of connector locations.

This electronic control board manages appliance functions and settings, restoring responsive control and reliable operation when the original board fails. It replaces a faulty or non-responsive main control to help the unit run correctly. What it does:

• Receives input from user controls and sensors and sends commands to motors, valves, and displays
• Replaces a board that causes unresponsive buttons, erratic cycles, or no power to controlled components
• Helps resolve issues like intermittent operation, incorrect cycle behavior, or loss of control functions
• Works as the main logic/control interface for appliance operation

• One control board only

• Disconnect power before accessing electrical components to avoid shock or damage
• Handle the board by edges; avoid touching circuitry or connector pins
• Verify connectors and harness orientation before reconnecting; secure mounting to prevent vibration damage

This electronic control is the main circuit board that manages oven functions, display and user inputs so your range responds correctly to temperature and bake/clean commands. Replaces a failed control to restore normal oven operation. What it does:

• Processes touchpad or selector inputs and runs oven cycles (bake, broil, timer, etc.)
• Drives the front display/clock so time and settings are visible
• Commands heating elements/relays to regulate oven temperature
• Can stop operation or show error codes when a fault is detected
• Prevents or corrects symptoms like unresponsive controls, blank or flashing display, and ovens that won't start

• One electronic control (main oven control board)

• Disconnect power at the breaker or unplug the appliance before servicing
• Handle the board carefully to avoid static damage; avoid touching circuit traces
• Some installs require removing the console or back panel and transferring mounting hardware and connectors

This replacement segment is a small OEM appliance component that secures or aligns adjacent parts inside select refrigerators and freezers, restoring proper fit and reducing noise or misalignment. What it does

• Helps hold or align panels, rails, or internal trim pieces for a snug fit
• Restores proper component spacing to prevent rubbing or vibration
• Can stop minor rattles or shifting caused by a missing or damaged segment
• Useful when interior trim or support points appear loose or misaligned

• One replacement segment as shown

• Turn off power to the appliance before accessing internal panels—unplug or shut off breaker
• Remove only the panels needed to reach the damaged segment; keep fasteners organized for reassembly
• Handle plastic segments gently to avoid cracking; use appropriate trim tools or a small screwdriver if needed

The Control Board is an OEM part for Frigidaire ranges and ovens. It is responsible for managing various functions and operations of the appliance. This crucial component receives input from the control panel and user settings, and then translates these inputs into commands for the different components of the range, such as the oven heating elements, bake and broil functions, temperature regulation, and timer operations.

Causes of a faulty Control Board can be related to electrical issues, such as power surges, short circuits, or internal component failure due to age or wear and tear.

Symptoms of a bad Control Board can include: 

• Oven not heating or maintaining temperature properly
• Oven control panel not responding or displaying erratic behavior 
• Specific oven functions not working correctly
• Error codes or warning lights illuminated on the control panel

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.