Electrolux Wall Oven Gasket & Seal

The Oven Door Seal is an OEM part for Frigidaire wall ovens and ranges. Located around the outer perimeter of the oven door, this silicone seal forms a tight insulation barrier when closed. Maintaining appropriate interior temperatures relies on an intact door seal.

Causes of a bad oven door seal can include cracking, crumbling or compression from repeated use over many years. Food debris or residue left on the seal surface may also degrade sealing ability.

Symptoms of a bad oven door seal include:

• Difficulty closing or sealing the oven door tightly
• Visible gaps around the door allowing heat escape
• Higher energy bills from the oven running excessively
• Uneven or unreliable cooking temperatures

This OEM Frigidaire oven door seal is also compatible with some Electrolux, Gibson, Kelvinator and Kenmore wall oven models.

The Dryer Seal is an OEM replacment part for Frigidaire dryers. It is located at the doorway opening where the drum rotates and helps prevent lint, moisture, and heat from escaping. The seal is a crucial component that ensures efficient drying and heat retention within the dryer drum. 

Causes of a bad seal can include wear and tear over time from continuous use or damage due to mishandling. The nylon seal experiences a lot of friction and heat stress with each drying cycle.

Symptoms of a bad seal include: 

• Increased drying time as heat escapes 
• Excess lint and moisture accumulation inside dryer components
• Visibly worn or cracked seal edges
• Cool air leakage noticed around the door when the dryer is running

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

The Oven Seal is an OEM replacement part for Frigidaire ovens. This seal is installed around the oven door to create a tight barrier, preventing heat from escaping during operation. By maintaining the internal temperature, the seal ensures efficient cooking and baking while reducing energy consumption.

Over time, the oven seal can wear out or become damaged due to exposure to high temperatures, frequent use, or accidental mishandling. A compromised seal can lead to heat loss, uneven cooking, or longer preheating times.

Symptoms of a bad oven seal include:

• Heat escaping from the oven door
• Longer cooking times or unevenly cooked food
• The oven taking longer to preheat
• Visible cracks, tears, or flattening of the seal

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Seal is an OEM part for Frigidaire ranges. This seal creates a tight barrier to prevent heat from escaping during cooking. Maintaining a proper seal ensures that the oven operates efficiently, maintains the correct temperature, and provides even cooking results.

Causes of a bad range door seal can include wear and tear from regular use, exposure to high temperatures, or damage from cleaning tools.  

Symptoms of a bad range door seal include:

• Heat escaping from around the oven door
• Uneven cooking or longer cooking times
• Visible cracks, tears, or deformation on the seal
• The oven door not closing tightly

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This replacement seal restores a tight barrier between mating parts in your appliance, helping contain air, moisture, or fluid so the unit operates efficiently and reliably over time.

• Provides a compressible barrier between components to prevent escaping air or liquids
• Helps maintain proper performance when the original seal is worn or deformed
• Common symptoms include poor sealing, seepage around a joint, or visible cracks/flattening
• Replace if cut, brittle, misshapen, or no longer seats securely

• Disconnect power; shut off water or gas supply before servicing
• Note the seal's orientation and seating depth before removal
• Clean mating surfaces and grooves; avoid sharp tools that could damage the new seal
• Seat the new seal evenly all the way around; reassemble and test for a proper seal

This oven door gasket creates a tight seal between the door and the oven frame to hold in heat and help maintain consistent cooking temperatures. Replacing a worn seal can improve preheat times and reduce heat loss and spills from escaping.

• Seals the oven door perimeter to minimize heat and moisture loss
• Helps the oven reach and maintain set temperatures more reliably
• Can address issues like longer preheat, uneven baking, or heat escaping around the door
• Replaces gaskets that are torn, flattened, frayed, or brittle

• Disconnect power and allow the oven to cool completely before service
• Open the door and carefully remove the old gasket from its clips or channel
• Clean the sealing surfaces to remove debris and residue
• Seat the new gasket evenly around the perimeter without stretching or twisting

This adhesive seal tape is a replacement sealing strip used to restore a tight seal on appliance doors and panels, helping reduce air leaks and improve temperature control. It's a simple repair for worn or damaged seal edges. What it does:

• Provides a flexible, adhesive sealing surface to close gaps between door/panel and cabinet
• Helps reduce air or moisture leakage that can cause temperature loss or inefficient operation
• Restores worn or deteriorated sealing surfaces without replacing the entire gasket
• Compatible with applications where a narrow adhesive sealing strip is required

• Clean and dry the mounting surface thoroughly before applying for best adhesion
• Measure and trim the tape to fit; press firmly along the full length to ensure contact
• Allow adhesive to set per ambient conditions before closing the door or returning to service

This burner seal fits around a cooktop burner to help keep spills and debris out of the burner housing and provide a stable, centered burner location for consistent heating. It restores a flush seal between the burner and the cooktop surface. What it does:

• Forms a protective gasket around the burner to block food, grease and liquids from entering the cooktop cavity
• Cushions and centers the burner, reducing wobble and promoting even element-to-surface contact
• Helps reduce smoke or odors caused by spills burning on exposed internal surfaces
• Restores proper fit after a cracked, torn or missing seal

• One burner seal

• Disconnect power to the appliance before servicing; if the range is gas, shut off the gas supply
• Remove the burner or lift the cooktop per your model's service instructions to access the seal area
• Clean and dry the mounting surface thoroughly before installing the new seal
• Press the seal into place; do not stretch excessively or use solvents/adhesives unless your model's instructions specify