Electrolux Control Board

The Defrost Timer is an OEM replacement part for Frigidaire upright freezers. It serves as a crucial component responsible for regulating automatic defrost cycles.

Causes of a faulty defrost timer relate to 20,000+ hours of constant exposure to freezer temperatures as low as -10 degrees Fahrenheit. Such extremes can compromise electrical switching mechanisms over prolonged usage periods.

Symptoms of a failed defrost timer include:

• Inability to initiate automatic defrost modes  
• Excessive ice and frost accumulation inside cabinet
• Warm areas detected due to impaired fan circulation
• Diagnostic codes indicating defrosting problems

This genuine Frigidaire replacement part is compatible with Kelvinator and some Kenmore units as well.

The Clock is an OEM part for Frigidaire ovens and ranges. It is the central electronic component that regulates and monitors oven functions such as bake, broil, convection, temperature controls, and timers.

Causes can be failures in the integrated circuitry, damaged connectors or traces on the board, or water or other environmental damage over time.

Symptoms of a clock include:

• Failure of oven elements to heat properly
• Unresponsive or inaccurate temperature displays
• Irregular timed baking or errors flashing
• Problems with convection or baking modes
• Power issues such as the oven not turning on

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Oven Control Board is an OEM part for Frigidaire ovens. It serves as the central hub for managing the oven’s various functions, including temperature regulation, timer settings, and heating modes. This electronic component receives input from the user through the control panel and sends signals to various oven components to ensure proper operation according to the selected settings.

Causes of a bad Oven Control Board can include electrical issues such as short circuits, power surges, or component failures due to age or faulty manufacturing.

Symptoms of a bad Oven Control Board include:

• Oven failing to heat,
• Display errors or blank screen,
• Unresponsive controls or settings that do not adjust properly,
• Inconsistent heating or temperature fluctuations.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Control Board is an OEM part for Frigidaire ranges. This component manages the various functions of the range, including temperature regulation, timing, and the operation of heating elements. It is the central hub for controlling the cooking process.

Causes of a bad range control board can include power surges, which can damage the electronic components, prolonged exposure to high temperatures, and general wear and tear over time. Additionally, moisture or spills can cause short circuits or corrosion.

Symptoms of a bad range control board include:

• The range not turning on
• Inconsistent or incorrect oven temperatures
• Display or buttons not functioning properly
• Error codes appearing on the control panel

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Oven Control Board is an OEM replacement part for Frigidaire ovens. This component serves as the brain of the oven, managing and regulating various functions such as temperature control, timer settings, and heating elements. It ensures that the oven operates efficiently, providing the desired heat levels for precise cooking and baking.

Symptoms of a bad Oven Control Board include:

• The oven is not heating or overheating
• Inconsistent temperatures leading to uneven cooking
• The display showing error codes or malfunctioning
• The oven not responding to input settings

Causes for a malfunctioning Oven Control Board can include electrical surges, wear and tear from regular use, or issues with the connections or components on the board itself.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Clock is an OEM part for Frigidaire ovens and ranges. This electronic component not only serves as a time display but also plays a pivotal role in the appliance's operation, allowing users to set timers, program cooking cycles, and in some models, control oven functions. 

Causes of a malfunctioning clock can include electrical surges that damage the circuitry, normal wear and tear affecting its functionality over time, and moisture or grease infiltration from cooking that can lead to short circuits or component damage.

Symptoms of a malfunctioning Clock include:

• The display is erratic or completely blank, making it impossible to read the time or set functions.
• Inability to program the oven or use the timer, affecting cooking precision.
• Intermittent operation, where the clock might reset randomly or fail to respond to controls.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Control Board is an OEM replacement part for Frigidaire refrigerators. This component serves as the brain of the appliance, managing and coordinating various functions such as temperature control, defrost cycles, and the operation of fans and compressors. A functional control board ensures the refrigerator maintains optimal performance and energy efficiency.

Control boards can fail due to power surges, electrical issues, or normal wear over time. A malfunctioning board can disrupt the refrigerator's functionality and impact its ability to preserve food effectively.

Symptoms of a bad control board include:

• Inconsistent or incorrect temperatures in the refrigerator or freezer
• Unresponsive controls or display panel issues
• The refrigerator not cooling or running continuously
• Error codes or unusual noises during operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Control Board is an OEM part for Frigidaire ranges. This part manages and regulates the functions of the range, including the oven temperature, cooking modes, and timing, ensuring precise control and efficient operation.

Causes of a bad control board can include electrical surges, overheating, or component failures due to regular wear and tear.  

Symptoms of a bad Control Board include:

• The range or oven not powering on
• Inaccurate temperature settings
• The display showing error codes or not functioning properly
• Unresponsive or malfunctioning buttons and controls

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This is a motor control board for a washing machine. It comes with the board, tape, bracket, and screw mounted on control. In most cases, this part is located on the bottom of the appliance near the drive motor. The purpose is to control the speed of the drive motor. It also works to determine the direction of the tumble and spin actions while a cycle is in process. If the washing machine is pumping but does not spin, this is often the result of a malfunctioning motor control board.If the motor control board has gone bad, it should be replaced. To replace it, make sure the washer is unplugged or the circuit breaker has been turned off. Pull the washer away from the wall, remove the knobs from the front and screws from the back, and lift the control panel. This offers access to the motor control board, which should be removed so the new part can be installed.This motor control board is made for use with washing machines by Electrolux, Frigidaire, Crosley, and Kenmore. It is sold on an individual basis. This is an authentic OEM replacement part that is directly sourced from the manufacturer.

The Control Board is an OEM replacement part for Frigidaire dryers. It is the central processing unit that controls all functions and operations of the dryer. The board receives input from sensors, activates heating elements and motor controls, and determines dryness levels based on temperature, moisture, and time settings. 

Causes of a bad control board can include failure due to wear and tear over time, exposure to heat and electrical stresses during normal operating cycles, as well as damage due to external impact or moisture intrusion. 

Symptoms of a bad control board include: 

• The dryer not starting or powering on
• Display/touchpad malfunctions 
• Failure to progress through cycles
• Inability to achieve set heat or time settings
• Erratic programs or operation

This OEM replacement is also compatible with Electrolux and some Kenmore model dryers.

The Clock is an OEM component for Frigidaire ranges and stoves. It displays the current time and functions as a timer to assist with cooking. 

Symptoms of a bad clock include:

• Incorrect time display
• Timer not working properly such as prematurely ending or displaying an inaccurate countdown

Clocks can fail due to normal wear over extended use of the appliance's electronic components and timer functions. Water damage from accidental spills or leaks could also potentially cause circuitry issues.

Please note: You may need to replace your overlay when replacing this part. Be sure to check your model to verify if it is required.

Replace yours today with this genuine Frigidaire OEM clock to restore full functionality. Proper timer operation and time display are important when preparing meals. This replacement part is also compatible with select RCA and Kenmore models for factory-quality repair.

The Clock is an OEM part for Frigidaire ranges. This part includes the display and control board that manages the oven's timer, clock functions, and sometimes additional settings such as cooking timers and delayed start features. 

Causes of a bad clock can include electrical issues, wear and tear from regular use, or physical damage from impacts or spills.

Symptoms of a bad clock include:

• The clock display not functioning or showing incorrect time
• Inability to set or use the timer functions
• The oven not responding to control inputs
• Error codes or intermittent operation of the control panel

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This part is a replacement control kit. It is made to replace a broken or ineffective part in some models of ovens and ranges.In order to monitor the temperature and control the oven settings, the control kit needs to be in proper working order. In cases where this part is warped, corroded, worn, broken, or in any way ineffective, the control kit will need to be immediately replaced. Prior to undergoing repairs, it's critical that the oven is entirely disconnected from the power source. Always wear work gloves when attempting an appliance repair.This is a genuine OEM part that has been manufactured by Frigidaire and has been sourced directly from the manufacturer to ensure high quality. This control kit can be used with various different models of ovens and ranges that have been manufactured by brands that include Frigidaire, Electrolux, Gibson, Westinghouse, and others. This is a genuine OEM part and thus is made of high-quality, durable materials and is sold individually.

This electronic oven control board is the brain of your range or wall oven. Replacing a failed board restores the display and keypad response and allows the appliance to heat and run bake/broil cycles reliably again.

• Controls relays for bake and broil circuits
• Uses oven sensor feedback to regulate and maintain temperature
• Powers the time/temperature display and reads keypad inputs
• Common symptoms: blank or erratic display, unresponsive buttons, F-code errors, oven won't heat or shuts off mid-cycle

• Disconnect power at the breaker before servicing; allow the appliance to cool
• Static-sensitive component—handle by the edges and avoid touching circuitry
• Note/photograph wire locations; transfer connectors one at a time to the new board
• Mount the board in the control panel, secure connections, restore power, and test

This compressor inverter control board powers and regulates the variable-speed compressor in your refrigerator by converting household AC into the controlled output the compressor needs. Replacing a failed inverter can restore compressor operation and normal cooling performance.

• Receives commands from the main control to vary compressor speed for efficient, steady cooling
• Converts AC line voltage to the controlled output required by the compressor motor
• Common symptoms of failure: refrigerator warm, compressor not running while fans/lights operate
• May also present as intermittent cooling, clicking or humming near the compressor, or visible damage on the module

• Disconnect power before servicing; this is a high-voltage component mounted at the compressor
• Note wire positions and transfer connectors one at a time; ensure all connections are fully seated
• Secure the module to the original mounting to maintain proper heat dissipation and vibration control

This electronic oven control board manages the bake/broil circuits and the clock/timer display. Replacing a failed board restores accurate temperature control and responsive keypad/display operation so your range can heat and time reliably again. What it does:

• Regulates power to the bake and broil elements based on temperature sensor feedback
• Interprets keypad inputs and drives the digital clock/timer display and alerts
• Controls oven relays for preheat, maintain-temp, and timed-cook functions
• Common failure symptoms include: no heat or intermittent heating, blank or unresponsive display, beeping/error indications, or oven that won't shut off

• 1 electronic control board

• Disconnect power at the breaker before servicing; verify no voltage is present
• Handle the board by the edges and use ESD protection to avoid static damage
• Note/photograph wire locations; transfer any mounting hardware or overlay from the original as applicable
• After installation, restore power, set the clock, and test all oven modes