Electrolux Wall Oven Parts

This is the glass panel used in the oven door window. Replace it to restore a clear view into the oven and maintain the door's proper heat barrier if the original pane is cracked, shattered, or damaged.

• Forms the viewing window and thermal barrier in the oven door
• Helps the oven retain heat for consistent cooking
• Direct replacement for a cracked, shattered, or missing pane
• Typical symptoms: visible cracks, shattered glass, rattling fragments, or reduced visibility

• Disconnect power or gas and allow the oven to cool completely before service
• Wear cut-resistant gloves and eye protection; handle broken glass with care
• Support the door; remove the door and any trim as outlined in your model's service information
• Transfer any reusable brackets/trim from the original glass and avoid overtightening fasteners

Note: Quantity is one tool (right side) 

Left side tool is part # AP3778569

Main electronic control board that manages the appliance's timing, temperature and cycle functions, restoring responsive controls and consistent operation when the original board fails or behaves erratically. What it does:

• Regulates key functions and signals between user controls, sensors, and motors to run cycles correctly.
• Controls timing and sequences for compressors, fans, defrost/heater circuits and other automatic functions.
• Replaces a failed board that causes unresponsive buttons, blank or error displays, or erratic cycling.
• Can resolve intermittent operation and failures tied to electronic control faults (diagnose before replacing).

• Disconnect power to the appliance before starting any service to avoid electric shock.
• Handle the board carefully and avoid static discharge; use ESD precautions if possible.
• Installation typically requires removal of the control panel and careful reconnection of wire harnesses; keep track of connector locations.

NOTE: The factory has removed the catalyst (honeycomb) from this tube adapter. The catalyst is no longer available.

This is a replacement screw used to secure appliance panels and components. It restores proper fastening so panels, trim, or assemblies stay tight and reduce vibration or rattling. What it does

• Fastens panels, brackets, or trim to the appliance chassis
• Helps stop loose or vibrating panels and trim pieces
• Restores proper alignment where a missing or stripped screw causes gaps or movement
• Use when the original screw is missing, damaged, or corroded

• One replacement screw as shown

• Disconnect power to the appliance before starting any repair
• Use the correct screwdriver or bit to avoid stripping the screw head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Keep removed screws in a safe place; this screw matches the original before installation

This harness assembly is the appliance wiring connector bundle that carries power and signals between controls and components, restoring proper electrical connections for normal operation. What it does:

• Routes power and control signals between the control board and key components
• Replaces damaged, burned, or loose wiring that can cause intermittent operation
• Helps resolve symptoms like unresponsive controls, failure to start, or component loss of power
• Restores factory wiring layout and connector fit for reliable connections

• Disconnect power before starting; confirm power is off at the breaker
• Compare connectors and wire colors to the old harness before removal
• Route and secure harness to avoid heat or pinch points; use existing clips/mounts

This adhesive seal tape is a replacement sealing strip used to restore a tight seal on appliance doors and panels, helping reduce air leaks and improve temperature control. It's a simple repair for worn or damaged seal edges. What it does:

• Provides a flexible, adhesive sealing surface to close gaps between door/panel and cabinet
• Helps reduce air or moisture leakage that can cause temperature loss or inefficient operation
• Restores worn or deteriorated sealing surfaces without replacing the entire gasket
• Compatible with applications where a narrow adhesive sealing strip is required

• Clean and dry the mounting surface thoroughly before applying for best adhesion
• Measure and trim the tape to fit; press firmly along the full length to ensure contact
• Allow adhesive to set per ambient conditions before closing the door or returning to service

This access panel cover secures and protects internal components behind an appliance opening, keeping parts safe from dust and preventing accidental contact. It restores the appliance's finished appearance and helps maintain proper airflow around covered areas. What it does:

• Shields wiring and components from dirt, dust and accidental contact
• Helps prevent small items from entering service areas
• Restores a clean, finished look to the appliance exterior or interior
• Supports safe airflow patterns when installed as intended

• One replacement cover

• Disconnect power before servicing; follow all safety guidelines for your appliance
• Typically secures with screws or clips—retain original fasteners or use OEM replacements
• Align cover to mounting points and fasten evenly to avoid gaps or stress

This thermal cut-out is a temperature-sensing safety device that helps protect the refrigerator's defrost/heater circuit by opening the circuit when temperatures exceed safe levels. It prevents overheating and helps maintain normal defrost cycles. What it does:

• Senses temperature in the defrost/heater area and opens the circuit to stop heating if temperatures get too high
• Prevents overheating of defrost heater or related components
• Can cause defrost failure symptoms when faulty, such as excessive frost buildup or poor cooling
• May also contribute to long run-times or irregular defrost cycles when not operating correctly

• Disconnect power to the appliance before servicing to avoid electrical shock
• Handle the part and wiring gently; ensure correct orientation and secure connections per service manual
• Use the exact replacement part number for compatibility