Electrolux Wall Oven Parts

This Main top is the oven's upper cabinet panel that provides the flat surface and structural support for the cooktop area, restoring proper fit and appearance. It replaces a bent, damaged, or corroded top to help the range sit and seal correctly. What it does:

• Replaces the damaged or warped top panel that supports the cooktop and front controls
• Restores a flat, even surface to prevent gaps and improve alignment with adjoining panels
• Helps prevent heat and moisture from reaching internal components through damaged metal
• Commonly replaced when the top shows dents, rust, or mounting-point damage

• One Main top (upper cabinet panel) as shown

• Basic disassembly of the cooktop and control panel is typically required; disconnect power before starting
• Handle edges carefully; metal panels can be sharp
• Keep hardware organized for reassembly; reuse original screws and brackets unless damaged

This steel-and-glass maintop is the upper cooking surface that supports burners and cookware while providing a finished appearance. Replaces a damaged or worn maintop to restore safe, level support and proper burner alignment. What it does:

• Provides the main cooking surface and mounting points for burners and grates
• Restores a flat, heat-resistant surface for pots and pans
• Helps prevent burners from shifting or tilting during use
• Improves appearance by replacing cracked, dented, or warped tops

• Verify power is disconnected and range is cool before starting work
• Use proper tools to remove burner grates, trim pieces, and mounting screws
• Handle glass surfaces carefully to avoid chipping; support the top during removal and installation

This burner seal fits around a cooktop burner to help keep spills and debris out of the burner housing and provide a stable, centered burner location for consistent heating. It restores a flush seal between the burner and the cooktop surface. What it does:

• Forms a protective gasket around the burner to block food, grease and liquids from entering the cooktop cavity
• Cushions and centers the burner, reducing wobble and promoting even element-to-surface contact
• Helps reduce smoke or odors caused by spills burning on exposed internal surfaces
• Restores proper fit after a cracked, torn or missing seal

• One burner seal

• Disconnect power to the appliance before servicing; if the range is gas, shut off the gas supply
• Remove the burner or lift the cooktop per your model's service instructions to access the seal area
• Clean and dry the mounting surface thoroughly before installing the new seal
• Press the seal into place; do not stretch excessively or use solvents/adhesives unless your model's instructions specify

This control mounting lock secures the washer control or door latch area so the machine runs safely and reliably. It replaces a worn or broken mounting lock to restore proper control-panel or latch stability during cycles. What it does:

• Holds the washer control or latch assembly firmly in place to prevent movement and intermittent connections
• Helps maintain reliable electronic or mechanical engagement during start and spin cycles
• Common symptom: control panel or door area feels loose, intermittently unseated, or causes error codes related to a loose latch/control
• Prevents excess vibration or shifting of the control/latch that can lead to premature wear

• One control mounting lock

• Disconnect power and water before servicing to avoid shock or injury
• Access may require removing the cabinet or control panel; follow for safe disassembly
• Inspect surrounding clips and connectors; replace any damaged fasteners for a secure fit

This electronic control is the main circuit board that manages oven functions, display and user inputs so your range responds correctly to temperature and bake/clean commands. Replaces a failed control to restore normal oven operation. What it does:

• Processes touchpad or selector inputs and runs oven cycles (bake, broil, timer, etc.)
• Drives the front display/clock so time and settings are visible
• Commands heating elements/relays to regulate oven temperature
• Can stop operation or show error codes when a fault is detected
• Prevents or corrects symptoms like unresponsive controls, blank or flashing display, and ovens that won't start

• One electronic control (main oven control board)

• Disconnect power at the breaker or unplug the appliance before servicing
• Handle the board carefully to avoid static damage; avoid touching circuit traces
• Some installs require removing the console or back panel and transferring mounting hardware and connectors

This element hanger support secures a cooktop surface heating element to the range and keeps the element aligned for reliable contact and stable cooking. Replaces a worn or bent bracket to restore proper element positioning. What it does:

• Holds the surface heating element in the correct position under the cooktop
• Stabilizes the element to maintain solid electrical contact and even heating
• Helps prevent element wobble, arcing, or intermittent power to the burner
• Fits where the element connects to the terminal/anchor point on the cooktop

• 1 element hanger support bracket

• Disconnect power to the appliance before attempting any service
• Remove the cooktop or element as required to access the hanger; follow OEM disassembly steps
• Inspect element terminals and surrounding parts for damage while replacing the bracket

A single replacement mounting screw used to secure appliance panels, trim, or small brackets. Restores proper fastening so parts stay aligned and eliminates loose or rattling components. What it does:

• Fastens panels, brackets, or trim pieces to the appliance frame
• Secures components that vibrate or shift during normal use
• Helps stop rattling, misalignment, or gaps caused by a missing or loose screw
• Works as a direct hardware replacement where the OEM screw is required

• One screw

• Use the correct driver and size to avoid stripping the head
• Tighten until snug; do not over-torque to prevent thread damage
• Disconnect power or follow appliance safety procedures before accessing internal components
• Replace all like fasteners for best fit

This mounting bracket secures appliance components in place to restore stable operation and alignment. It's a simple, durable replacement that helps prevent loose parts and rattling for safer, quieter performance. What it does:

• Provides structural support for internal components and assemblies
• Holds panels, modules or hardware in correct alignment to prevent movement
• Helps eliminate rattling, vibration noise, or loose-fitting parts
• Restores proper fit where a worn or broken bracket allowed misalignment

• Turn off power to the appliance and unplug before beginning work
• Remove only the panels or fasteners necessary to access the old bracket
• Reuse original fasteners or replace with equivalent-size hardware; tighten securely

This decorative trim bezel restores a clean finished look to the appliance's opening or control area and covers gaps or fasteners for a factory appearance. It's a direct-fit cosmetic replacement that helps maintain the original styling. What it does

• Covers and protects the edge of the opening or control panel for a finished appearance
• Hides mounting hardware and seals small gaps between panels
• Helps reduce dirt and grime buildup along the appliance opening edges
• Common symptom: cracked, scratched, missing, or warped trim that affects appearance

• Disconnect power to the appliance before starting work to avoid shock or injury
• Trim typically secures with clips or screws; keep and reuse original fasteners when possible
• Handle edges carefully—trim pieces may have sharp metal or plastic edges
• Check adjacent panels and mounting points for damage before forcing the trim into place