Parts for Poulan 967061501: Engine Parts

Returns the handguard to forward position on chainsaws. Replace if broken, damaged, or handguard no longer springs back when released. Restores safety.

Replace your worn, cracked, or damaged chainsaw throttle control lever. This plastic lever installs on the handle to control engine speed during operation.

Replace your broken or missing chainsaw choke knob. This control knob adjusts airflow to the carburetor. Direct replacement for worn or damaged knobs.

Pleated air filter captures debris before it reaches the carburetor and engine. Replace when dirty or clogged to maintain performance. Verify fit using your model number.

Manifold base for gas chainsaws. Mounts between the carburetor and cylinder to provide a secure connection. Replace if cracked, warped, or damaged.

Fix your chainsaw that won't start or runs poorly with a new air valve assembly. Controls airflow from filter to carburetor for proper engine operation.

The carburetor is the part of the chainsaw that mixes air from the intake valve system and gas before the fuel mixture goes to the engine. This ensures that the chainsaw is capable of continuing to run while it is in use. A bad carburetor will cause problems with how the chainsaw runs, and it may stop running during work. If the engine does not start when the tank is full of fresh fuel, test the carburetor. Start by removing the air filter and pouring a teaspoon of fuel onto the carburetor. Then, pull the starter rope to start the engine. If the engine starts but quickly dies, it means that the carburetor will likely need to be replaced. The replacement of the new carburetor is fairly simple. Remove the rear cover on the chainsaw to remove the old carburetor. Once you have removed the old carburetor, you can then install the new carburetor. Replace the cover and test the chainsaw. This is an OEM sourced part that will work with several models of chainsaws from Poulan and Craftsman.

Throttle control cable for chainsaws. Connects the throttle trigger to the carburetor. Replace if cable is frayed, broken, or binding for proper speed control.

Engine gasket kit for chainsaws. Replace when you notice oil leaks, loss of compression, or during engine rebuilds. Verify fit with your model number.

Replace missing, stripped, or damaged mounting screws on your chainsaw or trimmer. Standard hardware fastener for securing components and housings.

Loss of power or engine won't start? This chainsaw piston kit restores compression and performance. Includes cylinder components for reliable operation.

Fix excessive vibration and poor engine performance with this chainsaw cylinder kit. Houses the piston in the engine. Moderate repair skill required.

Replace a worn crankshaft assembly if your chainsaw won't start, runs rough, or has excessive vibration. This repair requires engine disassembly.

Replace your chainsaw's seal and bearing assembly to reduce friction and stabilize moving parts. Essential for smooth operation. Verify fit with your model.

M6-1.0 x 25mm bolt for chainsaws. Secures various components on the saw body. Replace if stripped, corroded, missing, or damaged during disassembly.

Secures the muffler cover to the muffler on chainsaws and small engines. Replace if screw is stripped, missing, or no longer holds the cover securely.

Spark arrestor kit for chainsaws. Installs in the muffler exhaust to prevent sparks from escaping. Replace if screen is damaged, clogged, or missing.

Replacement muffler backplate for gas chainsaws. Secures between muffler and engine block. Replace if cracked, warped, or missing to ensure proper fit.

Controls spark timing in gas chainsaws. Replace if cracked housing, corroded terminals, or damaged wiring prevents proper ignition signal transmission.

This replacement part is a screw. This part is a genuine replacement part made by Husqvarna. Screws are small but important in many different types of machinery. Screws are able to hold different parts in place and help them stay secure during use so that the machine can operate smoothly and efficiently. A new screw might be needed if the current one is missing or damaged in any way. It is possible that the screw can become stripped over time and therefore not stay in place properly. If this is the case it is recommended that it be replaced. This repair should be fairly easy and only require a screwdriver and possible pliers. This part is sold individually and is sourced directly from the manufacturer to ensure proper fit and long-lasting use. Note that This is a genuine OEM replacement part.