Parts for Bosch B36CD50SNS/01: Evaporator & Heat Element Parts

This heating element is the oven/dryer-style heater assembly that provides controlled heat for drying or cooking cycles, restoring proper temperature during operation. It fits specific Bosch appliances. What it does

• Heats the appliance interior so dryers can remove moisture or ovens can reach set temperatures.
• Restores normal heating when a failed element causes no heat or weak heat.
• Works with the appliance's thermostat and controls to maintain set temperatures.
• Common symptom: no heat, insufficient heat, or longer cycles.

• Disconnect power (and gas, if applicable) before starting any repair.
• Removal typically requires access to the appliance's rear or front panel; follow the OEM service manual.
• Inspect and test related parts (thermal fuse, thermostat, wiring) if heating problems persist.

This thermal fuse is a one-time temperature safety cutoff that stops power when overheating is detected, protecting the appliance and reducing fire risk. It's a direct-replacement safety device for units that use a single thermal cutoff. What it does:

• Interrupts electrical flow to the heater or control circuit when excessive temperature is reached
• Prevents the appliance from operating while an over-temperature condition persists
• Common symptom: appliance runs but does not heat or suddenly stops heating
• Common symptom: appliance fails to start or power is cut after overheating

• Intended for service technicians or experienced DIYers only
• Disconnect power before testing or replacing the fuse to avoid shock or injury
• Do not bypass or defeat this safety device; replace with the exact type specified by the manufacturer
• Verify proper airflow and heating system operation after replacement to prevent repeat failures

The Switch is an OEM component specifically designed for Bosch refrigerators. It is an electronic control located inside refrigerator doors.  

The switch allows for contactless powering of interior LED lighting and audible alerts when doors are opened. Convenient visibility of contents is provided.

Causes of switch failure can include repeated opening and closing wear over time. Moisture exposure may corrode internal circuitry as well.

Symptoms of a bad switch include:

• Lights fail to turn on when doors are opened
• Audible chimes/alerts ceasing to sound as intended
• Visible damage or corrosion on the switch housing

This OEM Bosch replacement part is also compatible with Thermador, Gaggenau, and some Kenmore refrigerators utilizing corresponding switch technologies. Replacement ensures that intended convenience features remain operational.

This motor drives the dishwasher's circulation/pump assembly to move wash water through the spray arms for proper cleaning. Replacing a worn motor restores water flow and helps return the appliance to normal wash performance. What it does

• Powers the wash/pump assembly to circulate water during the wash and rinse cycles
• Restores normal water flow when the original motor fails or loses torque
• Common symptom fixes: dishwasher leaves dishes poorly cleaned, reduced or no water circulation, humming or stalled motor noise
• Works as the mechanical drive for the pump/impeller that routes wash water through spray arms

• One motor (assembly) as shown

• Disconnect power to the appliance before any service; follow lockout/tagout if applicable
• Turn off water supply and remove lower access panels to reach the pump/motor area
• Handle the motor carefully; confirm electrical connector and mounting orientation before removal
• Replace any gaskets, seals, or impellers separately if damaged or leaking

This replacement cover is a simple exterior access panel that protects internal components and restores a finished appearance. It keeps wiring and mechanisms shielded while keeping the appliance looking complete. What it does:

• Shields internal components from dirt, dust and accidental contact
• Helps reduce noise by covering openings where parts are mounted
• Restores the appliance's finished look if the original cover was cracked or missing
• Can prevent small objects from falling into service areas and causing damage

• Disconnect power to the appliance before beginning any work
• Remove fasteners or clips securing the old cover; keep screws for reuse if applicable
• Align cover carefully to avoid pinching wiring or misplacing mounting tabs

This locking cap secures small components in place to maintain proper alignment and operation. It's a simple replacement that helps restore fit and prevents parts from coming loose during normal use. What it does:

• Holds and secures the associated component or assembly in place
• Restores proper fit to stop shifting, rattling or misalignment
• Helps prevent damage from loose parts during appliance operation
• Commonly replaced when the original cap is cracked, broken, or missing

• One locking cap

• Disconnect power and water supply before starting any repair
• Small part; keep track of hardware and orientation during removal
• Use basic hand tools as needed and avoid forcing parts to prevent breakage